Physics for Scientists and Engineers, Technology Update (No access codes included)
9th Edition
ISBN: 9781305116399
Author: Raymond A. Serway, John W. Jewett
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 33, Problem 33.6CQ
As shown in Figure CQ33.6, a person pulls a vacuum cleaner at speed v across a horizontal floor, exerting
on it a force of magnitude F directed upward at an angle θ with the horizontal. (a) At what rate is the person doing work on the cleaner? (b) State as completely as you can the analogy between power in this situation and in an electric circuit.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
In a hydroelectric dam, water falls 30.0 mm and then spins a turbine to generate electricity.
You may want to review (Pages 234 - 238) .
What is ΔUΔUDeltaU of 1.0 kg of water?
Express your answer with the appropriate units.
Suppose the dam is 80% efficient at converting the water's potential energy to electrical energy. How many kilograms of water must pass through the turbines each second to generate 51.0 MWMW of electricity? This is a typical value for a small hydroelectric dam.
Express your answer using three decimal places.
Choose the correct answer choice.
A sled and rider with combined mass of 85 kg are perched atthe top of a hill. The top of this hill is 40 m above level groundbelow. A second bump is a hill 20 m above the ground.Suppose that we also know that approximately 3500 J of workis done against friction as the sled travels between these twopoints. (a) Choosing ground as a reference level, what is thepotential energy of sled and rider at the top of first hill? (b)Will the sled make it to the top of the second bump if no kineticenergy is given to sled at the start of its motion? Explain. c) Iffriction is ignored, what will be the speed of the sled and rider at the bottom of hill
Chapter 33 Solutions
Physics for Scientists and Engineers, Technology Update (No access codes included)
Ch. 33 - Consider the voltage phasor in Figure 32.4, shown...Ch. 33 - Consider the AC circuit in Figure 32.8. The...Ch. 33 - Consider the AC circuit in Figure 32.11. The...Ch. 33 - Consider the AC circuit in Figure 32.12. The...Ch. 33 - Label each part of Figure 32.16, (a), (b), and...Ch. 33 - An AC source drives an RLC circuit with a fixed...Ch. 33 - What is the impedance of a series RLC circuit at...Ch. 33 - An inductor and a resistor are connected in series...Ch. 33 - (i) When a particular inductor is connected to a...Ch. 33 - A capacitor and a resistor are connected in series...
Ch. 33 - Prob. 33.4OQCh. 33 - Prob. 33.5OQCh. 33 - A sinusoidally varying potential difference has...Ch. 33 - A series RLCcircuit contains a 20.0- resistor, a...Ch. 33 - A resistor, a capacitor, and an inductor are...Ch. 33 - (a) Why does a capacitor act as a short circuit at...Ch. 33 - What is the plia.se angle in a series RLC circuit...Ch. 33 - Prob. 33.11OQCh. 33 - A 6.00-V battery is connected across the primary...Ch. 33 - Do AC ammeters and voltmeters read (a)...Ch. 33 - (a) Explain how the quality factor is related to...Ch. 33 - (a) Explain how the mnemonic ELI the ICE man can...Ch. 33 - Why is the sum of the maximum voltages across each...Ch. 33 - (a) Does the phase angle in an RLC series circuit...Ch. 33 - Prob. 33.5CQCh. 33 - As shown in Figure CQ33.6, a person pulls a vacuum...Ch. 33 - Prob. 33.7CQCh. 33 - Will a transformer operate if a battery is used...Ch. 33 - Prob. 33.9CQCh. 33 - Prob. 33.10CQCh. 33 - When an AC source is connected across a 12.0-...Ch. 33 - (a) What is the resistance of a lightbulb that...Ch. 33 - An AC power supply produces a maximum voltage Vmax...Ch. 33 - A certain lightbulb is rated at 60.0 W when...Ch. 33 - The current in the circuit shown in Figure P32.3...Ch. 33 - In the AC circuit shown in Figure P32.3, R = 70.0 ...Ch. 33 - An audio amplifier, represented by the AC I source...Ch. 33 - Figure P32.4 shows three lightbulbs connected to a...Ch. 33 - An inductor has a .54.0- reactance when connected...Ch. 33 - In a purely inductive AC circuit as shown in...Ch. 33 - Prob. 33.11PCh. 33 - An inductor is connected to an AC power supply...Ch. 33 - An AC source has an output rms voltage of 78.0 V...Ch. 33 - A 20.0-mH inductor is connected to a North...Ch. 33 - Review. Determine the maximum magnetic flux...Ch. 33 - The output voltage of an AC source is given by v =...Ch. 33 - A 1.00-mF capacitor is connected to a North...Ch. 33 - An AC source with an output rms voltage of 86.0 V...Ch. 33 - (a) For what frequencies does a 22.0-F capacitor...Ch. 33 - A source delivers an AC voltage of the form =...Ch. 33 - What maximum current is delivered by an AC source...Ch. 33 - A capacitor C is connected to a power supply that...Ch. 33 - What is the maximum current in a 2.20-F capacitor...Ch. 33 - An AC source with Vmax = 150 V and f = 50.0 Hz is...Ch. 33 - In addition to phasor diagrams showing voltages...Ch. 33 - A sinusoidal voltage = 40.0 sin 100t, where is...Ch. 33 - A series AC circuit contains a resistor, an...Ch. 33 - At what frequency does the inductive reactance of...Ch. 33 - An RLC circuit consists of a 150- resistor, a...Ch. 33 - Prob. 33.30PCh. 33 - An inductor (L = 400 mH), a capacitor (C = 4.43...Ch. 33 - A 60.0-ft resistor is connected in series with a...Ch. 33 - Review. In an RLC series circuit that includes a...Ch. 33 - Prob. 33.34PCh. 33 - A series RLC circuit has a resistance of 45.0 and...Ch. 33 - An AC voltage of the form = 100 sin 1 000t, where...Ch. 33 - A series RLC circuit has a resistance of 22.0 and...Ch. 33 - An AC voltage of the form v = 90.0 sin 350t, where...Ch. 33 - ln a certain series RLC circuit, Irms = 9.00 A,...Ch. 33 - Prob. 33.40PCh. 33 - Prob. 33.41PCh. 33 - A series RLC circuit has components with the...Ch. 33 - An RLC circuit is used in a radio to tune into an...Ch. 33 - The LC circuit of a radar transmitter oscillates...Ch. 33 - A 10.0- resistor, 10.0-mH inductor, and 100-F...Ch. 33 - A resistor R, inductor L, and capacitor C are...Ch. 33 - Review. A radar transmitter contains an LC circuit...Ch. 33 - A step-down transformer is used for recharging the...Ch. 33 - The primary coil of a transformer has N1 = 350...Ch. 33 - A transmission line that has a resistance per unit...Ch. 33 - In the transformer shown in Figure P33.51, the...Ch. 33 - A person is working near the secondary of a...Ch. 33 - The RC high-pass filter shown in Figure P33.53 has...Ch. 33 - Consider the RC high-pass filler circuit shown in...Ch. 33 - Prob. 33.55PCh. 33 - Consider the Filter circuit shown in Figure...Ch. 33 - A step-up transformer is designed to have an...Ch. 33 - Prob. 33.58APCh. 33 - Review. The voltage phasor diagram for a certain...Ch. 33 - Prob. 33.60APCh. 33 - Energy is to be transmitted over a pair of copper...Ch. 33 - Energy is to be transmitted over a pair of copper...Ch. 33 - A 400- resistor, an inductor, and a capacitor are...Ch. 33 - Show that the rms value for the sawtooth voltage...Ch. 33 - A transformer may be used to provide maximum power...Ch. 33 - A capacitor, a coil, and two resistors of equal...Ch. 33 - Marie Cornu, a physicist at the Polytechnic...Ch. 33 - A series RLC circuit has resonance angular...Ch. 33 - Review. One insulated conductor from a household...Ch. 33 - (a) Sketch a graph of the phase angle for an RLC...Ch. 33 - In Figure P33.71, find the rms current delivered...Ch. 33 - Review. In the circuit shown in Figure P32.44,...Ch. 33 - Prob. 33.73APCh. 33 - A series RLC circuit is operating at 2.00 103 Hz....Ch. 33 - A series RLC circuit consists of an 8.00-...Ch. 33 - A series RLC circuit in which R = l.00 , L = 1.00...Ch. 33 - The resistor in Figure P32.49 represents the...Ch. 33 - An 80.0- resistor and a 200-mH inductor are...Ch. 33 - Prob. 33.79CPCh. 33 - P33.80a shows a parallel RLC circuit. The...Ch. 33 - Prob. 33.81CP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- Why do we need to be careful about work done on the system versus work done by the system in calculations?arrow_forwardA particle moves in the xy plane (Fig. P9.30) from the origin to a point having coordinates x = 7.00 m and y = 4.00 m under the influence of a force given by F=3y2+x. a. What is the work done on the particle by the force F if it moves along path 1 (shown in red)? b. What is the work done on the particle by the force F if it moves along path 2 (shown in blue)? c. What is the work done on the particle by the force F if it moves along path 3 (shown in green)? d. Is the force F conservative or nonconservative? Explain. FIGURE P9.30 In each case, the work is found using the integral of Fdr along the path (Equation 9.21). W=rtrfFdr=rtrf(Fxdx+Fydy+Fzdz) (a) The work done along path 1, we first need to integrate along dr=dxi from (0,0) to (7,0) and then along dr=dyj from (7,0) to (7,4): W1=x=0;y=0x=7;y=0(3y2i+xj)(dxi)+x=7;y=0x=7;y=4(3y2i+xj)(dyj) Performing the dot products, we get W1=x=0;y=0x=7;y=03y2dx+x=7;y=0x=7;y=4xdy Along the first part of this path, y = 0 therefore the first integral equals zero. For the second integral, x is constant and can be pulled out of the integral, and we can evaluate dy. W1=0+x=7;y=0x=7;y=4xdy=xy|x=7;y=0x=7;y=4=28J (b) The work done along path 2 is along dr=dyj from (0,0) to (0,4) and then along dr=dxi from (0,4) to (7,4): W2=x=0;y=0x=0;y=4(3y2i+xj)(dyj)+x=0;y=4x=7;y=4(3y2i+xj)(dyi) Performing the dot product, we get: W2=x=0;y=0x=0;y=4xdy+x=0;y=4x=7;y=43y2dx Along the first part of this path, x = 0. Therefore, the first integral equals zero. For the second integral, y is constant and can be pulled out of the integral, and we can evaluate dx. W2=0+3y2x|x=0;y=4x=7;y=4=336J (c) To find the work along the third path, we first write the expression for the work integral. W=rtrfFdr=rtrf(Fxdx+Fydy+Fzdz)W=rtrf(3y2dx+xdy)(1) At first glance, this appears quite simple, but we cant integrate xdy=xy like we might have above because the value of x changes as we vary y (i.e., x is a function of y.) [In parts (a) and (b), on a straight horizontal or vertical line, only x or y changes]. One approach is to parameterize both x and y as a function of another variable, say t, and write each integral in terms of only x or y. Constraining dr to be along the desired line, we can relate dx and dy: tan=dydxdy=tandxanddx=dytan(2) Now, use equation (2) in (1) to express each integral in terms of only one variable. W=x=0;y=0x=7;y=43y2dx+x=0;y=0x=7;y=4xdyW=y=0y=43y2dytan+x=0x=7xtandx We can determine the tangent of the angle, which is constant (the angle is the angle of the line with respect to the horizontal). tan=4.007.00=0.570 Insert the value of the tangent and solve the integrals. W=30.570y33|y=0y=4+0.570x22|x=0x=7W=112+14=126J (d) Since the work done is not path-independent, this is non-conservative force. Figure P9.30ANSarrow_forwardRank the potential energies of the four systems of particles shown in Figure OQ20.6 from largest to smallest. Include equalities if appropriate. Figure OQ20.6arrow_forward
- Haliade-X 12 MW is one of the most powerful offshore wind turbines in the world and it will be installed in the New Jersey offshore area (Figure 1). Energy storage is a long-time problem for wind energy, because the period of wind power is not necessary at the peak of electricity demand. To match the power supply and demand, the generated energy has to be stored either in battery or other forms. There is an idea to use the tower of the wind turbine as energy storage – sea water is pumped to the top of the tower when power generation is more than demand; and water is released to drive a generator at the base of the tower to supply energy when it is needed. Assume the turbine tower is 20 m below the sea bottom and the water depth is 30 m, and the tower is filled by sea water (density = 1030 kg/m3). Answer the questions below (make sure your answer is in both gauge pressure and absolute pressure form). At the mean sea level, how much is the pressure between inside and outside the…arrow_forwardA coin slides over a frictionless plane and across an xy coordinate system from the origin to a point with xy coordinates (3.60 m, 9.50 m) while a constant force acts on it. The force has magnitude 4.10 N and is directed at a counterclockwise angle of 114.° from the positive direction of the x axis. How much work is done by the force on the coin during the displacement? Number T16.941 Unitsarrow_forwardA family in Charlotte wants to drive to a campsite next to Mt. Mitchell. Their trip will take them 2km up in elevation. They have the choice of taking their Tesla (EV), which when fully charged has 100 kWh of stored energy in the batteries (and for this problem is 100% efficient at converting its stored energy into kinetic energy) and a mass of 2200kg, or their choice of taking their Ford F-150. Gasoline has an energy density of 34.2 Megajoules per liter. The Ford's fuel tank contains 23 gallons. Assume the Ford’s engine is able to convert 30% of the energy stored in its gasoline tank into kinetic energy (typical efficiency for gasoline engines), with the rest of the stored energy in the gasoline lost to heat. The mass of the Ford is about 2000kg. They are going to tow their big pop-up trailer to the campsite. For this question, assume that each vehicle must use a combined 79 kWh of energy to combat the wind resistance of moving at 75 mph with the trailer for the whole drive, and to…arrow_forward
- E (a) Calculate is the change in PE when an electron moves through an electric field, E = 50 N/C, directed to the right, a distance of 6 m to the left. V Potential Energy, APE: ✓ J (b) Is mechanical energy of the electron conserved during the motion? Yes No (c) If the electron starts from rest what is its speed, v₁, after traveling 6 m? The mass of the electron is me =9.1×10-³¹ kg. Vf= ✔m/sarrow_forwardTwo persons were practicing social distancing to alleviate the spread of COVID-19. Social distancing requires a minimum of 3 feet distance from person to person. However, due to their eagerness to share some rumors, the two persons decided to approach each other and now within the intimate distance (12 inches). If person A weighs 60 kg. and person B weighs 68 kg., determine the work done for this act. Take G = 6.67408 × 10-11 m³ kg-ls-2. A. 6.8076 ergs C. 5.9559 ergs D. 5.5599 ergs B. 8.0766 ergsarrow_forwardTwo persons were practicing social distancing to alleviate the spread of COVID-19. Social distancing requires a minimum of 3 feet distance from person to person. However, due to their eagerness to share some rumors, the two persons decided to approach each other and now within the intimate distance (12 inches). If person A weighs 60 kg. and person B weighs 68 kg., determine the work done for this act. Take G = 6.67408 × 10-11 m³ kg-1s-2. A. 6.8076 ergs B. 8.0766 ergs C. 5.9559 ergs D. 5.5599 ergsarrow_forward
- Two persons were practicing social distancing to alleviate the spread of COVID-19. Social distancing requires a minimum of 3 feet distance from person to person. However, due to their eagerness to share some rumors, the two persons decided to approach each other and now within the intimate distance (12 inches). If person A weighs 60 kg. and person B weighs 68 kg., determine the work done for this act. Take G = 6.67408 × 10-11 m3 kg-1s-2arrow_forwardPracticearrow_forwardHow much power is needed to lift a 750 kg elephant 14.3 m in 30.0 seconds? Paragraph V B I U A/ Ev + varrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Physics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
Physics for Scientists and Engineers, Technology ...
Physics
ISBN:9781305116399
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Electric Fields: Crash Course Physics #26; Author: CrashCourse;https://www.youtube.com/watch?v=mdulzEfQXDE;License: Standard YouTube License, CC-BY