Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 31, Problem 7ASRQ
While discussing a high idle speed problem: Technician A says that higher-than-normal idle speed may be caused by low electrical system voltage. Technician B says that higher-than-normal idle speed may be caused by a defective coolant temperature sensor. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
While discussing secondary voltage: Technician A says that the normal required secondary voltage is higher at idle speed than at wide open throttle conditions. Technician B says that the maximum available secondary voltage must always exceed the normally required secondary voltage. Who is correct?
An overheating vehicle is being discussed.
Technician A states that the vehicle may be
overheating because the heater control valve
is stuck closed. Technician B states that the
vehicle may be overheating because the
PCM in not energizing the cooling fan relay.
Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
An overheating vehicle is being discussed.
Technician A states that the thermostat is
open until the engine fully warms up.
Technician B states that the vehicle may be
overheating because the thermostat is stuck
closed. Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
Chapter 31 Solutions
Automotive Technology
Ch. 31 - List four service precautions for working on the...Ch. 31 - What is indicated by a LTFT reading of 24 percent?Ch. 31 - Describe how testing GDI fuel systems differs from...Ch. 31 - What is the difference between the pulse width and...Ch. 31 - How can you use a dual trace scope to make sure...Ch. 31 - What are three possible problems that can allow...Ch. 31 - What is the purpose of having two accelerator...Ch. 31 - What is indicated by a negative LTFT value?Ch. 31 - What problem may result from dirt buildup on an...Ch. 31 - What is the difference between STFT and LTFT?
Ch. 31 - True or False? The signals from an air-fuel ratio...Ch. 31 - Prob. 2TFCh. 31 - Which of the following is the most likely cause of...Ch. 31 - The PCM checks for a closed throttle plate each...Ch. 31 - Which of the following would not cause a...Ch. 31 - While discussing the causes of...Ch. 31 - While discussing IAC valve diagnosis: Technician A...Ch. 31 - While discussing IAC motor removal, service, and...Ch. 31 - While discussing injector testing: Technician A...Ch. 31 - While discussing airflow sensors: Technician A...Ch. 31 - While discussing scan tool diagnosis of fuel...Ch. 31 - While discussing a high idle speed problem:...Ch. 31 - While discussing the causes of a rich air-fuel...Ch. 31 - While diagnosing an idle speed problem: Technician...Ch. 31 - While looking at fuel trim values: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that installing a thermostat incorrectly can cause the housing to break. Technician B says that it is OK to install a thermostat in either direction. Who is correct? Select one: a. Technician A only b. Technician B only C. Both A and B d. Neither A nor Barrow_forwardWhile discussing ignition timing control in EI systems: Technician A says that when the engine coolant temperature is low, the timing is retarded until normal operating temperature is reached. Technician B says that the PCM will retard the timing during EGR operation. Who is correct? Technician Ac.Both A and B b. Technician B d. Neither A nor Barrow_forwardThe clamping of a work piece is to be controlled by either of two Push buttons. A further push button isto control declamping.Additional conditions:a) clamping is only possible when a work piece is presentb) declamping is to be interlocked during drillingc) the clamping speed is to be slow and adjustabled) declamping is to be very fast Draw the pneumatic circuit diagram using ISO symbols and connecting the ports with solid lines.arrow_forward
- Two techs are discussing oil coolers. Technician A says that when inspecting oil- to-water type coolers, look for mixing of the fluids: oil in the coolant, and coolant in the oil. Technician B says that when inspecting oil-to-air type coolers, look for oil in the coolant only. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardA hot-wire MAF has low resistance across it when the wire is hot: Technician A says that this condition will cause the engine to stall as soon as you put the transmission into gear. Technician B says that this condition will cause the transmission to shift late. Who is correct?arrow_forwardAutomotive cooling system problems are being discussed. Technician A states that engine overheating is a common failure. Technician B states that an engine remaining below proper engine operating temperature is a common failure. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forward
- Technician A says that you may be able to smell antifreeze from a leaking heater core. Technician B says that you may be able to hear a loose belt when the engine is running. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTrue or False: Pneumatic controls are explosion-proof.arrow_forwardone way flow control valve is the type of valve which is used to control the speed of an actuator. Select one: O True O Falsearrow_forward
- Technician A says that some shift solenoids can be activated by providing a ground for the solenoid. Technician B says that some shift solenoids can be activated by applying hydraulic pressure to their valve. Who is correct?arrow_forwardTechnician A says that some types of voltage sensors provide input to the computer by modifying or controlling a constant, predetermined voltage signal. Technician B says that a coolant temperature sensor is a voltage-generating sensor. Who is correct?arrow_forwardHYDRAULICS & ELECTRO-HYDRAULICSarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license