EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 8220100793431
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 31, Problem 25QLP
Discuss the factors that influence the strength of (a) a diffusion-bonded and (b) a cold-welded component.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Provide a reasonable explanation for the following observation: a welded component made of Al 6061-T6 alloy is routinely found to deform plastically first in the region adjacent to the weld joint despite the fact that the stress is nominally the same everywhere in the component. What solution would you propose to fix this problem, assuming that the weld joint cannot be eliminated from the design?
An arc welding operation on nickel performs a groove weld, whose cross-sectional area = 20.0 mm2. The melting point of nickel Tm = 1725° Travel velocity = 4.0 mm/sec. Heat transfer factor = 0.82, and melting factor = 0.70. Determine the rate of heat generation required at the welding source to accomplish this weld.
A gas metal arc welding test is performed to determine the value of melting factor f₂ for a
certain metal and operation. The welding voltage = 25 volts, current = 125 amps, and heat
transfer factor is assumed to be = 0.90, a typical value for GMAW. The rate at which the
filler metal is added to the weld is 0.50 in³ per minute, and measurements indicate that the
final weld bead consists of 57% filler metal and 43% base metal. The unit melting energy
for the metal is known to be 75 Btu/in³. (a) Find the melting factor. (b) What is the travel
speed if the cross-sectional area of the weld bead = 0.05 in²?
Chapter 31 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 31 - Explain what is meant by solid-state welding.Ch. 31 - What is cold welding? Why is it so called?Ch. 31 - What is (a) a ferrule, (b) filled gold, and (c) a...Ch. 31 - What are faying surfaces in solid-state welding...Ch. 31 - What is the basic principle of (a) ultrasonic...Ch. 31 - Explain how the heat is generated in the...Ch. 31 - Prob. 7RQCh. 31 - Describe the principle of resistance-welding...Ch. 31 - Prob. 9RQCh. 31 - What type of products are suitable for stud...
Ch. 31 - Prob. 11RQCh. 31 - Prob. 12RQCh. 31 - Prob. 13RQCh. 31 - Describe how high-frequency butt welding operates.Ch. 31 - What materials are typically used in...Ch. 31 - Make a list of processes in this chapter,...Ch. 31 - Prob. 17QLPCh. 31 - Explain the reasons why the processes described in...Ch. 31 - Explain the similarities and differences between...Ch. 31 - Describe your observations concerning Figs....Ch. 31 - Would you be concerned about the size of weld...Ch. 31 - What advantages does friction welding have over...Ch. 31 - Prob. 23QLPCh. 31 - Prob. 24QLPCh. 31 - Discuss the factors that influence the strength of...Ch. 31 - What are the sources of heat for the...Ch. 31 - Can the roll-bonding process be applied to a...Ch. 31 - Prob. 28QLPCh. 31 - List and explain the factors involved in the...Ch. 31 - Give some of the reasons that spot welding is...Ch. 31 - Prob. 31QLPCh. 31 - Prob. 32QLPCh. 31 - Prob. 33QLPCh. 31 - Prob. 34QLPCh. 31 - Prob. 35QLPCh. 31 - Prob. 36QLPCh. 31 - Prob. 37QLPCh. 31 - Prob. 38QLPCh. 31 - Which processes in this chapter are not affected...Ch. 31 - Consider the situation where two round...Ch. 31 - Prob. 41QLPCh. 31 - The energy required in ultrasonic welding is found...Ch. 31 - Prob. 43QTPCh. 31 - Prob. 44QTPCh. 31 - Prob. 45QTPCh. 31 - Prob. 46SDPCh. 31 - Explain how you would fabricate the structures...Ch. 31 - Prob. 48SDPCh. 31 - Prob. 49SDPCh. 31 - Prob. 50SDPCh. 31 - Prob. 51SDPCh. 31 - Prob. 52SDPCh. 31 - Prob. 53SDPCh. 31 - Describe the methods you would use for removing...Ch. 31 - Prob. 55SDPCh. 31 - Prob. 56SDPCh. 31 - Inspect the sheet-metal body of an automobile,...Ch. 31 - Prob. 59SDPCh. 31 - Prob. 60SDPCh. 31 - Sketch the microstructure you would expect if a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- (b) Two flat aluminum sheets (each 1 mm thick) are being spot welded by use of a current of 5000A and a current flow time of 0.2 s. The electrodes are 3 mm in diameter. Assume that the resistance is 200µ2. Given the density of aluminum is 2.70 g/cm³ and the latent heat of fusion (hf) for aluminum is 321 J/g.arrow_forwardTwo 1.2 mm thick sheets of steel are joined by double-sided spot welding using a current of 6000A and current flow time of t = 0.15 sec. The electrodes are 3 mm in diameter and the weld spot thickness is approximately one third of the total thickness of the metal sheets. Assuming that the effective resistance in this operation is 200 micro resistance, estimate the heat generated and its distribution in the weld zone. (Take density of steel = 8600 Kg/m3 and its latent heat capacity, L =1400 J/g)arrow_forwardThe unit melting energy for a certain sheet metal is 10J/mm^3 .The thickness of each of the two sheets to be spot-welded is = mm. To achive required strength, it is desired to form a weldnugget that is =7 mm in diameter and 3.5 mm thick. The weld duration will be set at 44 sec .If the electrical resistance between the two surfaces is 144 micro-ohms and only one half the electricity generated will be used to form the weld nugget Determine the minium current level required in this operationarrow_forward
- Two 1.2 mm thick flat copper sheets are being spot welded using a current of 6000A and a current flow time of 0.18 s. The electrodes are 5 mm in diameter. Estimate the generated in the weld zone. Take effective resistance as 150 ohm. also calculate temperature rise assuming that the heat generated is confined to the volume ogf materials directly between two electrodes and temperature is uniformly distributed.arrow_forwardAn electron-beam welding operation will join two pieces of steel plate together. The plates are 2.5 cm thick. The unit melting energy is 8050 J/cm3. The diameter of the work area focus of the beam is 0.15 cm, hence the width of the weld will be 0.15 cm. The accelerating voltage is 30 kV and the beam current is 35 milliamp. The heat transfer factor is 0.70 and the melting factor is 0.55. If the beam moves at a speed of 125 cm/min, will the beam penetrate the full thickness of the platesarrow_forwardANSWER FAS WITH A SUMMARIZED SOLUTIONarrow_forward
- Two 1.2 mm thick flat copper sheets are being spot welded using a current of 6000 A and a current flow time of 0.18 s. The electrodes are 5 mm in diameter. Estimate the heat generated in the weld zone. Take effective resistance as 150 µΩ. Also calculate temperature rise assuming that the heat generated is confined to the volume of material directly between the two electrodes and temperature is uniformly distributed.arrow_forwardThe client wishes to save weight in their assembly and has suggested using aluminium for the joining block. Evaluate the suitability of this material from a structural viewpoint, the client has indicated available space is very limited so dimensional changes should be minimal. Advise if aluminium is feasible as an alternative material and justify your answer. Would titanium be a suitable option? The properties of both materials are shown below. Titanium – E 102.81 GPa: v 0.36: shear 44000 MPa: yield 275.6 MPa: tensile 344.5 MPa Aluminium – E 68.9 GPa: v 0.33: shear 25864MPa: yield 275 MPa: tensile 310 MPaarrow_forwardResistance spot welding is performed on two plates of 1.5 mm thickness with 6 mm diameter electrode, using 15000 A current for a time duration of 0.25 seconds. Assuming the interface resistance to be 0.00010, the heat generated ( W-sec) to form the weld isarrow_forward
- Identify the conditions under which a brazed joint is likely to be “stronger” than the brazing material by itself. Describe the trends in joint fracture strength as it becomes wider/narrower or thinner/thicker.arrow_forwardA fillet weld on low carbon steel has a cross‑sectional area of 25.0 mm2 and is 900 mm long. Determine (a) the amount of heat required to perform the weld, and (b) the amount of heat that must be generated by the heat source, if the heat transfer factor = 0.90 and the melting factor = 0.60?arrow_forwardWhat is the principal benefit of a joint action with a mechanical advantage less than 1.0? What is the principal benefit of a joint action with a mechanical advantage greater than 1.0?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License