Electric Motor Control
10th Edition
ISBN: 9781133702818
Author: Herman
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 3, Problem 3SQ
If a motor starter is installed according to directions but will not start, what is a common cause for the failure to start?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Can I use the Manual Motor Starter on a single phase motor? Why?
What causes the overload of a starter to open and disable the power circuit?
2. Assume that when the START button is pressed
M starter does not energize. List seven possible
causes for this problem.
Chapter 3 Solutions
Electric Motor Control
Ch. 3 - Prob. 1SQCh. 3 - How many poles are required on motor starters for...Ch. 3 - If a motor starter is installed according to...Ch. 3 - Using the time limit overload or the dashpot...Ch. 3 - What causes the AC hum or chatter in AC...Ch. 3 - What is the phase relationship between the flux in...Ch. 3 - In what AC and DC devices is the principle of the...Ch. 3 - What does the electrician look for to remedy the...Ch. 3 - What type of protective enclosure is most commonly...Ch. 3 - What advantage is there in using combination...
Ch. 3 - What safety feature does the combination starter...Ch. 3 - Prob. 12SQCh. 3 - How is the size of the overload heaters selected...Ch. 3 - What type of motor starter enclosure (include NEMA...Ch. 3 - Prob. 15SQCh. 3 - Prob. 16SQCh. 3 - Prob. 17SQCh. 3 - Prob. 18SQCh. 3 - Select the best answer for each of the following....Ch. 3 - Prob. 20SQCh. 3 - Prob. 21SQCh. 3 - Select the best answer for each of the following....Ch. 3 - Prob. 23SQCh. 3 - Select the best answer for each of the following....Ch. 3 - Select the best answer for each of the following....Ch. 3 - Select the best answer for each of the following....Ch. 3 - Select the best answer for each of the following....Ch. 3 - Prob. 28SQCh. 3 - Select the best answer for each of the following....Ch. 3 - Prob. 30SQCh. 3 - Prob. 31SQCh. 3 - What is the difference between a grounded control...Ch. 3 - A control transformer has a primary voltage of 480...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- One reason for the use of a reduced voltage starter would be to reduce the high starting current drawn by the motor. True or false?arrow_forwardThe starter must never operate for more than sixty seconds at a time and should rest for two minutes between extended cranking ? True or falsearrow_forwardAt standstill condition, the back emf is zero, so the motor can be safely turned ON without a starter. Select one: OTrue O Falsearrow_forward
- At standstill condition, the back emf is zero, so the motor can be safely turned ON without a starter. Select one: O True O False?arrow_forwardAnswer all or else skip the question pleasearrow_forwardlist the probable causes if the armature does not release after the magnetic starter is de-energized?arrow_forward
- Why do you think some motor control circuit utilizes single voltage sources for control and power circuit? Explain.arrow_forwardWhy must a discharge resistor be connected in the field circuit for starting?arrow_forwardA starter turns very slowly and has excessive cranking current draw. When removed from the vehicle and bench tested, the starter spins normally and current draw is within specifications. Technician A says poor battery connections may be the cause. Technician B says an internal engine problem may be the cause. Who is correct?arrow_forward
- c) Based on Figure 3 (c), a basic DOL starter induction motor at a power station is experiencing run-time error and unable to start, based on your understanding, interpret the sequence of troubleshooting shall be carried out to identify the root cause of the abnormalities. 3P 1P MCB MCB STOP K1 START MOTOR Figure 3 (c)arrow_forwardIf the contacts on a manual starter cannot be closed immediately after a motor overload has tripped them open, what is the probable reason?arrow_forwardwhat are designed to protect the motor from an overload conditionarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning
Single Phase Induction Motor, How it works ?; Author: Lesics;https://www.youtube.com/watch?v=awrUxv7B-a8;License: Standard Youtube License