Concept explainers
Apply nodal analysis to find io and the power dissipated in each resistor in the circuit of Fig. 3.64.
Figure 3.64
For Prob. 3.15.
Find the current
Answer to Problem 15P
The value of current
Explanation of Solution
Given data:
Refer to Figure 3.64 in the textbook for the nodal analysis. In the given circuit,
Calculation:
Modify the given figure with the representation of supernode and current direction as shown in Figure 1.
Apply Kirchhoff’s current law to the supernode in Figure 1.
Apply Kirchhoff’s current law to node
Reduce the given figure to provide voltage relation as shown in Figure 2.
Apply Kirchhoff’s voltage law to the circuit in Figure 2 to get relationship between voltages.
Represent the equations (1), (2), and (3) in matrix form.
Obtain the value of determinants as follows.
Write the expression for the voltages
Substitute
Substitute
Substitute
From Figure 1, write the expression for the current
Substitute
Write the expression for power dissipated in
Substitute
Write the expression for power dissipated in
Substitute
Write the expression for power dissipated in
Substitute
Conclusion:
Therefore, the value of current
Want to see more full solutions like this?
Chapter 3 Solutions
EBK FUNDAMENTALS OF ELECTRIC CIRCUITS
- For problems 1-4, select from the following list of raceway types. Check the letter(s) representing the correct response(s): a. electrical metallic tubing b. electrical nonmetallic tubing c. flexible metallic tubing d. rigid metal conduit e. intermediate metal conduit f. rigid nonmetallic conduit 1. Which raceway(s) may be used where cinder fill is present? ☐ a. ☐ b. ☐ c. ☐ d. ☐ e. 2. Which raceway(s) may be used in hazardous locations? ☐ a. b. ☐ c. ☐ d. 3. Which raceway(s) may be used in wet locations? ☐ a. ☐ b. ☐ c. ☐ d. ☐e. ☐ ☐ e. ☐ f. ☐ d. ☐ e. ☐ f. 4. Which raceway(s) may be used for service entrances? ☐ c. ☐ a. O b.arrow_forwardHANDWRITTEN SOLUTION NOT USING CHATGPT PLEASEarrow_forwardPEN & PAPER SOLUTION PLEASE NOT USING AIarrow_forward
- Pls show neat and whole solutionarrow_forwardI need help with this problem and an explanation of the solution for the image described below. (Introduction to Signals and Systems)arrow_forwardI need help with this problem and an explanation of the solution for the image described below. (Introduction to Signals and Systems)arrow_forward
- The input signal in the op-amp circuit of Fig. P7.80 is given by uin(t) =V0 coswt. Assuming the op amp is operating within its linear range, obtain an expression for your(t) by applying the phasor-domain technique and then evaluate it for wRC = 1.arrow_forwardFor ui(t)=V0 coswt, obtain an expression for uout(t) in thecircuit of Fig. P7.82 and then evaluate it for V0 = 4 V, w = 400rad/s, R = 5 kW, and C = 2.5 μF.arrow_forwardCan you help me to solve the question?arrow_forward
- The input signal in the op-amp circuit of Fig. P7.81 is givenbyuin(t) = 0.5cos2000t V.Obtain an expression for uout(t) and then evaluate it forR1 = 2 kW, R2 = 10 kW, and C = 0.1 μF.arrow_forwardHANDWRITTEN SOLUTION REQUIRED NOT USING CHATGPTarrow_forwardFundamentals of Energy Systems HW 2 Q2arrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,