CALC In Fig. 29.23 the capacitor plates have area 5.00 cm2 and separation 2.00 mm. The plates are in vacuum. The charging current iC has a constant value of 1.80 mA. At t = 0 the charge on the plates is zero. (a) Calculate the charge on the plates, the electric field between the plates, and the potential difference between the plates when t = 0.500 μs. (b) Calculate dE/dt, the time rate of change of the electric field between the plates. Does dE/dt vary in time? (c) Calculate the displacement current density jD between the plates, and from this the total displacement current iD. How do iC and jD compare?
Learn your wayIncludes step-by-step video
Chapter 29 Solutions
University Physics with Modern Physics Plus Mastering Physics with eText -- Access Card Package (14th Edition)
Additional Science Textbook Solutions
The Cosmic Perspective
Conceptual Physical Science (6th Edition)
The Cosmic Perspective (8th Edition)
College Physics
An Introduction to Thermal Physics
University Physics Volume 2
- At room temperature, What is the strength of the electric field in a 12-gauge copper wire with a diameter of 2.05mm that is needed to cause a 2.75A current to flow? What field would be needed if the wire were made of silver instead?arrow_forwardA (1.91x10^2)-mA current is used to charge up a parallel plate capacitor. A large square piece of paper is placed between the plates and parallel to them so it sticks out on all sides. What is the value of the integral P B. ds around the perimeter of the paper? Express your result in T.m with three significant figures.arrow_forwardAn air cylindrical capacitor with a dc voltage V= 200 V applied across it is being submerged vertically into a vessel filled with water at a velocity v = 5.0 mm/s. The electrodes of the capacitor are separated by a distance d = 2.0 mm, the mean curvature radius of the electrodes is equal to r = 50 mm. Find the current flowing in this case along lead wires, if d <r.arrow_forward
- The equations of the currents in two parallel-connected electric devices are i1 = 11.3 sin (377t + /4) and i2 = 8.5 sin (377t - /4). What is the rms value of the resultant current?arrow_forwardIn Fig.01, the variable cross section of a circular conductor with a non-uniform diameter that conducts a current of intensity I=5 A is shown. The radius of the cross section A1 is R1=0.4 cm. If the current density through A2 is one quarter of the value through A1, what is the radius of the conductor in A2? Fig.01 A2arrow_forwardA capacitor with square plates, each with an area of 37.0 cm2 and plate separation d = 2.44 mm, is being charged by a 555-mA current. (a) What is the change in the electric flux between the plates as a function of time? (Use the following as necessary: t. Do not use other variables, substitute numeric values. Assume that dΦE/dt is in V · m/s and t is in seconds. Do not include units in your answer. Enter the magnitude.)arrow_forward
- A cylindrical copper conductor with temperature coefficient 4.3x10^-3 K^-1 at room temperature (20 degrees C) has radius 3.0 cm. The magnitude of the electric inside the conductor obeys the relation (6.0 V/m^2)r and points in the same direction that the current travels. If you decrease the temperature to 10 degrees C, what is the current flowing through the conductor?arrow_forwardA capacitor with square plates, each with an area of 34.0 cm2 and plate separation d = 2.64 mm, is being charged by a 215-mA current. (a) What is the change in the electric flux between the plates as a function of time? (Use the following as necessary: t. Do not use other variables, substitute numeric values. Assume that dΦE/dt is in V · m/s and t is in seconds. Do not include units in your answer. Enter the magnitude.) dΦE dt = (b) What is the magnitude of the displacement current between the capacitor's plates?arrow_forwardE H A coaxial capacitor with inner radius 5 mm, outer radius 6 mm and length 500 mm has a dielectric for which e,=6.7 and an applied voltage 250 sin 377t (V). Determine the displacement current ip and compare with the conduction current i̟.arrow_forward
- What would the Hall voltage be (in µV) if a 2.20 T field is applied across a 12-gauge copper wire (2.052 mm in diameter) carrying a 24.0 A current? (Assume the free charge density of copper is 8.342 x 1028 e /m³.) HVarrow_forwardCh. 26arrow_forwardA copper wire has radius 0.800 mm and carries current I at20.0°C. A silver wire with radius 0.500 mm carries the same current andis also at 20.0°C. Let ECu be the electric field in the copper wire and EAgbe the electric field in the silver wire. What is the ratio ECu/EAg?arrow_forward
- College PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningUniversity Physics (14th Edition)PhysicsISBN:9780133969290Author:Hugh D. Young, Roger A. FreedmanPublisher:PEARSONIntroduction To Quantum MechanicsPhysicsISBN:9781107189638Author:Griffiths, David J., Schroeter, Darrell F.Publisher:Cambridge University Press
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningLecture- Tutorials for Introductory AstronomyPhysicsISBN:9780321820464Author:Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina BrissendenPublisher:Addison-WesleyCollege Physics: A Strategic Approach (4th Editio...PhysicsISBN:9780134609034Author:Randall D. Knight (Professor Emeritus), Brian Jones, Stuart FieldPublisher:PEARSON