DeGarmo's Materials and Processes in Manufacturing
12th Edition
ISBN: 9781118987674
Author: J. T. Black, Ronald A. Kohser
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 25, Problem 2P
How much time will be required to drill the hole in Problem 1 using the HSS drill?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 0.4-inch diameter bit is used in a vertical or vertical drill that operates at 300 rpm. If the feed is 0.005 in / rev, what is the MRR? What is the MRR if the drill diameter is doubled? What is the power required in the drill if the material is an annealed AISI 1080?
The part in Figure 1 is to be drilled on a turret-type drill press. The part is 15.0 mm thick. Threedrill sizes will be used: 8 mm, 10 mm, and 12 mm, which are to be specified in the part programby tool turret positions TO1, T02, and T03. All tooling is high speed steel. Cutting speed = 75mm/min and feed = 0.08 mm/rev. Use the lower-left corner of the part as the origin in the x-y axissystem. Write the part program in the word address format using absolute positioning.
With neat sketch explain the tap drill nomenclature?
Chapter 25 Solutions
DeGarmo's Materials and Processes in Manufacturing
Ch. 25 - What functions are performed by the flutes on a...Ch. 25 - What determines the rake angle of a drill? See...Ch. 25 - Basically, what determines what helix angle a...Ch. 25 - When a large-diameter hole is to be drilled, why...Ch. 25 - Equation 25.4 for the MRR for drilling can be...Ch. 25 - Are the recommended surface speeds for spade...Ch. 25 - What can happen when an improperly ground drill is...Ch. 25 - Why are many drilled holes oversize with respect...Ch. 25 - What are the two primary functions of a...Ch. 25 - What is the function of the margins on a twist...
Ch. 25 - What factors tend to cause a drill to drift off...Ch. 25 - The drill shown in Figure 25.13 has coolant...Ch. 25 - Prob. 13RQCh. 25 - Why do cutting fluids for drilling usually have...Ch. 25 - How does a gang-drilling machine differ from a...Ch. 25 - Prob. 16RQCh. 25 - How does the thrust force vary with feed? Why?Ch. 25 - Holding the workpiece by hand when drilling is not...Ch. 25 - Prob. 19RQCh. 25 - In terms of thrust, what is unusual about the...Ch. 25 - Prob. 21RQCh. 25 - Prob. 22RQCh. 25 - What are the primary purposes of reaming?Ch. 25 - What are the advantages of shell reamers?Ch. 25 - A drill that operated satisfactorily for drilling...Ch. 25 - What precautionary procedures should be used when...Ch. 25 - What is the advantage of a spade drill? Is it...Ch. 25 - Prob. 28RQCh. 25 - Why does drill feed increase with drill size?Ch. 25 - Suppose you specified a drilling feed rate that...Ch. 25 - Suppose you wanted to drill a 1.5-in.-diameter...Ch. 25 - How much time will be required to drill the hole...Ch. 25 - What is the metal removal rate when a...Ch. 25 - If the specific horsepower for the steel in...Ch. 25 - If the specific power of an AISI 1020 steel of...Ch. 25 - Prob. 6PCh. 25 - Assume that you are drilling eight holes, equally...Ch. 25 - What machining difficulties should this process...Ch. 25 - Why were the distances between the holes too...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
10.10 A main cable in a large bridge is designed for a tensile force of 2,600,000 lb. The cable consists of 147...
Applied Statics and Strength of Materials (6th Edition)
A large beverage cooler resembles a small building and is to be maintained at about 35 F (2 C) and a low relati...
Heating Ventilating and Air Conditioning: Analysis and Design
Determine the largest load P that can be applied to the frame without causing either the average normal stress ...
Mechanics of Materials
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Determine the magnitude and direction of the resultant force. Prob. F2-8
Engineering Mechanics: Statics
A pressure cooker has the lid screwed on tight. A small opening with A=5mm2 is covered with a petcock that can ...
Fundamentals Of Thermodynamics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- List two general types of upright drill press heads.arrow_forwardDescribe the relation between the letter size drills, fractional sized drills and the numbered drills?arrow_forwardQuestion 1 a.Define the following termsi)Driling and boring b.State the metal cutting tool used in drilingc.State the three types of drill pressesd.label 3 drill pressesarrow_forward
- QUESTION 5 Determine the spindle speed (rpm), the feed rate (in/min) and the cutting power required for turning a 1º diameter copper rod with a depth of cut of 0.1" using a cemented carbide tool. O N=287 RPM, F-25.8 in/min, P=9.7 hp ON=2866 RPM, F=258 in/min, P=97 hp ON=1146 RPM, F-25.8 in/min, P=97 hp O N= 11460 RPM, F-340 in/min, P=130 hp ON= 1146 RPM, F-34 inimin, P= 13 hp ON= 115 RPM, F-3.4 in/min, P=1.3 hp QUESTION 6 It is required to face mill an aluminum block to size it down from 2" to 1.5" thick using a 3" diameter 2-toothed carbide cutting tool. The block is 6.0" wide and 6" long. The entire tool diameter engages the workpiece during the cut. Calculate the recommended spindle speed in revolutions per minute, feed per tooth, and cutting power required. O N=1529 RPM, f= 0.026 in/rev/tooth, P = 36 hp O N-3820 RPM, f= 26 in/revitooth, P=27 hp O N-3820 RPM, f= 0.052 in/rew/tooth, P=27 hp ON-382 RPM, F= 0.026 in/revitooth, P = 0.027 hp O N-3820 RPM, f= 0.052 in/rev/tooth, P=2.7 hp…arrow_forwardFind the commercial tap drill size for 1⁄2”-20 NF bolt.arrow_forwardList the three parts of a common twist drill.arrow_forward
- 6q Read the sentences given below and Identify the wrong statement. Sentence 1. The advantage of an independent chuck is that the work can be centered to high precision. Sentence 2. The advantage of an independent chuck is that it is easy to work with. Sentence 2 is False None of the sentences are False Sentence 1 is False Sentence 1 and 2 are Falsearrow_forward1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel drill. At what speed in revolutions per minute should he operate the drill press? 2. Find the revolutions per minute of an 8 mm drill if it is used to cut an aluminum workpiece using a high carbon steel drill. 3. The rpm setting of the drill press is set to 600 rpm. What is the maximum diameter in inches of a high speed drill if it is used to drill a tool steel material? 4. A drill press has the following rpm settings; 350, 600, 1100, & 1600. What rpm setting must be used if a 15 mm high speed steel drill is used to cut brass workpiece? 5. A machine operator drills a hole of a 3/8 inch diameter to a stainless steel using a carbon steel drill. He sets the drill press rpm setting to 900 rpm. Is he operating at correct setting? If not, then what must be the correct rpm setting considering that the machine has the following rpm settings of 300, 600, 900, 1200, and 1800?arrow_forwardNeed accurate answer for this pleasearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY