Numerical Methods for Engineers
Numerical Methods for Engineers
7th Edition
ISBN: 9780073397924
Author: Steven C. Chapra Dr., Raymond P. Canale
Publisher: McGraw-Hill Education
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 24, Problem 1P

Perform the same computation as Sec. 24.1, but compute the amount of heat required to raise the temperature of 1200 g of the material from 150  to  100 ° C . Use Simpson's rule for your computation, with values of T  at 50 ° C increments.

Expert Solution & Answer
Check Mark
To determine

To calculate: The amount of heat required of 1200 g material by using Simpson’s rule, when temperature is increased from 150°C to 100°C.

Answer to Problem 1P

Solution:

The amount of heat required of 1200 g material by using Simpson’s ruleis 38892 cal.

Explanation of Solution

Given Information:

Write the value of the provided temperatures.

T1=150°C and T2=100°C

Write the value of the provided mass of the material.

m=1200 g

Write the value of the temperature increments.

ΔT=50°C

Formula used:

Write the expression of heat required when temperature is increased.

ΔH=mT1T2c(T)dT ,

And,

ΔT=T2T1

Write the expression of the heat capacity of the material, when temperature is increased.

c(T)=0.132+1.56×104T+2.64×107T2

The formula of the 1/3 Simpson’s rule for the number integration is as follows:

abf(x)dx=h6(f(a)+4f(a+b2)+f(b))

The formula of the 3/8 Simpson’s rule for the number integration is as follows:

abf(x)dx=h8(f(a)+3f(2a+b3)+3f(a+2b3)+f(b))

Here, h=ba

Calculation:

Calculate the value of the of c(T) at different values of T.

For T=150°C,

c(T=150°C)=0.132+1.56×104(150°C)+2.64×107(150°C)2=0.11454 cal/g°C

For T=100°C,

c(T=100°C)=0.132+1.56×104(100°C)+2.64×107(100°C)2=0.11904 cal/g°C

For T=50°C,

c(T=50°C)=0.132+1.56×104(50°C)+2.64×107(50°C)2=0.12486 cal/g°C

For T=0°C,

c(T=0°C)=0.132+1.56×104(0°C)+2.64×107(0°C)2=0.132 cal/g°C

For T=50°C,

c(T=50°C)=0.132+1.56×104(50°C)+2.64×107(50°C)2=0.14046 cal/g°C

For T=100°C,

c(T=100°C)=0.132+1.56×104(100°C)+2.64×107(100°C)2=0.15024 cal/g°C

Construct the table for heat capacity c(T) for different value of T.

T (°C)c(T)(cal/g°C)1500.114541000.11904500.1248600.132500.140461000.15024

Calculate the amount of heat required to increase the temperature of 1200g of material from T1=150°C to T2=100°C.

ΔH=m150100c(T)dT …… (1)

Use the integral in equation (1) by dividing the limits in two parts, that can be written as,

ΔH=m(15050c(T)dT+50100c(T)dT) …… (2)

Consider the integral as follows:

I=15050c(T)dT+50100c(T)dT …… (3)

Consider first part of the integral of I is,

I1=15050c(T)dT

Solve the above integral by using Simpson’s 1/3rd rule.

I1=50(150)6(f(150)+4f(150+(50)2)+f(50))=1006(f(150)+4f(100)+f(50))=1006(0.11454+4(0.11904)+0.12486)=11.926 cal/g

Consider the second part of integral I is,

I2=50100c(T)dT

Solve the above integral by using Simpson’s 3/8th rule.

I2=100(50)8(f(50)+3f(2(50)+1003)+3f(50+2(100)3)+f(100))=1508(f(50)+3f(0)+3f(50)+f(100))=1508(0.12486+3(0.132)+3(0.14046)+0.15024)=20.484 cal/g

Substitute 20.484 cal/g for I2 and 11.926 cal/g for I1 in equation (3).

I=I1+I2=11.926 cal/g+20.484 cal/g=32.41 cal/g

Substitute 32.41 cal/g for I and 1200 g for m in equation (2).

ΔH=mI=(1200 g)(32.41 cal/g)=38892 cal

Therefore, the heat required to increase temperature of the material by using Simpson’s ruleis 38892 cal.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Chapter 24 Solutions

Numerical Methods for Engineers

Ch. 24 - One of your colleagues has designed a new...Ch. 24 - Video an giography is used to measure blood flow...Ch. 24 - 24.14 Perform the same computation as in Sec....Ch. 24 - Perform the same computation as in Sec. 24.2, but...Ch. 24 - 24.16 As in Sec. 24.2, compute F using the...Ch. 24 - Stream cross-sectional areas (A) are required for...Ch. 24 - 24.18 As described in Prob. 24.17, the...Ch. 24 - 24.21 A transportation engineering study requires...Ch. 24 - 24.22 A wind force distributed against the side of...Ch. 24 - 24.23 Water exerts pressure on the upstream ...Ch. 24 - 24.24 To estimate the size of a new dam, you have...Ch. 24 - The data listed in the following table gives...Ch. 24 - The heat flux q is the quantity of heat flowing...Ch. 24 - 24.27 The horizontal surface area of a lake at a...Ch. 24 - 24.28 Perform the same computation as in Sec....Ch. 24 - 24.29 Repeat Prob. 24.28, but use five...Ch. 24 - Repeat Prob. 24.28, but use Romberg integration to...Ch. 24 - Faradays law characterizes the voltage drop across...Ch. 24 - 24.32 Based on Faraday’s law (Prob. 24.31), use...Ch. 24 - Suppose that the current through a resistor is...Ch. 24 - If a capacitor initially holds no charge, the...Ch. 24 - 24.35 Perform the same computation as in Sec....Ch. 24 - 24.36 Repeat Prob. 24.35, but use (a) Simpson’s ...Ch. 24 - 24.37 Compute work as described in Sec. 24.4, but...Ch. 24 - As was done in Sec. 24.4, determine the work...Ch. 24 - 24.39 The work done on an object is equal to the...Ch. 24 - The rate of cooling of a body (Fig. P24.40) can be...Ch. 24 - 24.41 A rod subject to an axial load (Fig....Ch. 24 - If the velocity distribution of a fluid flowing...Ch. 24 - 24.43 Using the following data, calculate the work...Ch. 24 - 24.44 A jet fighter’s position on an aircraft...Ch. 24 - 24.45 Employ the multiple-application Simpson’s...Ch. 24 - The upward velocity of a rocket can be computed by...Ch. 24 - Referring to the data from Problem 20.61, find the...Ch. 24 - Fully developed flow moving through a 40-cm...Ch. 24 - Fully developed flow of a Bingham plasticfluid...Ch. 24 - 24.50 The enthalpy of a real gas is a ...Ch. 24 - Given the data below, find the isothermal work...Ch. 24 - 24.52 The Rosin-Rammler-Bennet (RRB) equation is...Ch. 24 - For fluid flow over a surface, the heat flux to...Ch. 24 - The pressure gradient for laminar flow through a...Ch. 24 - 24.55 Velocity data for air are collected at...
Knowledge Booster
Background pattern image
Advanced Math
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, advanced-math and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Mathematics For Machine Technology
Advanced Math
ISBN:9781337798310
Author:Peterson, John.
Publisher:Cengage Learning,
Text book image
College Algebra
Algebra
ISBN:9781337282291
Author:Ron Larson
Publisher:Cengage Learning
Text book image
Trigonometry (MindTap Course List)
Trigonometry
ISBN:9781337278461
Author:Ron Larson
Publisher:Cengage Learning
Text book image
College Algebra
Algebra
ISBN:9781938168383
Author:Jay Abramson
Publisher:OpenStax
Text book image
Algebra: Structure And Method, Book 1
Algebra
ISBN:9780395977224
Author:Richard G. Brown, Mary P. Dolciani, Robert H. Sorgenfrey, William L. Cole
Publisher:McDougal Littell
Text book image
Algebra & Trigonometry with Analytic Geometry
Algebra
ISBN:9781133382119
Author:Swokowski
Publisher:Cengage
Mod-01 Lec-01 Discrete probability distributions (Part 1); Author: nptelhrd;https://www.youtube.com/watch?v=6x1pL9Yov1k;License: Standard YouTube License, CC-BY
Discrete Probability Distributions; Author: Learn Something;https://www.youtube.com/watch?v=m9U4UelWLFs;License: Standard YouTube License, CC-BY
Probability Distribution Functions (PMF, PDF, CDF); Author: zedstatistics;https://www.youtube.com/watch?v=YXLVjCKVP7U;License: Standard YouTube License, CC-BY
Discrete Distributions: Binomial, Poisson and Hypergeometric | Statistics for Data Science; Author: Dr. Bharatendra Rai;https://www.youtube.com/watch?v=lHhyy4JMigg;License: Standard Youtube License