Electrical Transformers and Rotating Machines
4th Edition
ISBN: 9781305494817
Author: Stephen L. Herman
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 21, Problem 5RQ
A 125-hp synchronous motor is connected to a 230-volt three-phase AC line. The motor is intended to operate at 80% power factor. What is the full-load running current of this motor? What are the minimum size NEMA and IEC starters that should be used to connect this motor to the line?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A (21 HP, 3-Phase, 380 volts) motor with an efficiency of 95% is operating at a load
factor of 0.63. What is the input current (Amperes) when the power factor is 89%? (1
HP = 0.75 kW)
please answer quickly!!
What is the minimum pulley diameter for a 1 HP motor running at 1750 RPM?
Chapter 21 Solutions
Electrical Transformers and Rotating Machines
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is the full-load running current of a three-phase, 50-hp motor connected to a 560-volt line? What are the minimum size NEMA and IEC starters that should be used to connect this motor to the line?arrow_forwardA 125 HP, synchronous motor is connected to a 230-volt, three phase AC line. The motor is intended to operate at 80 percent power factor. What is the full load running current of this motor? What is the minimum size NEMA and IEC starters that should be used to connect this motor to the line?arrow_forwardA 75-hp, three-phase squirrel-cage induction motor is connected to 480 volts. The motor has a NEMA code D. What is the starting current for this motor?arrow_forward
- A 150-horsepower motor is to be installed on a 480-volt three-phase line. What is the minimum size NEMA starter that should be used for this installation?arrow_forwardA 480-volt three-phase load is rated at 34.5 kVA. It is to be supplied with variable three-phase voltage. Because the load is continuous, the transformers ratings are to be increased by 1.25% of the rated load. Three variable autotransformers are used to supply this load. Refer to Table 4-2 and determine the standard size of each transformer that should be used to make this connection.arrow_forwardWhat is the speed of operation of the Holtz motor?arrow_forward
- Question 2 Beli vifth Slack side Motor (imprut) Tight side Beli thickpess\ Centre distance Figure 2 Figure 2 shows an open flat belt drive connected to a motor and a pulley. The motor transmits 20 kw to the connect pulley of 450 mm diameter and is rotating at 850 r/min to a second pulley rotating at 400 r/min. The distance between pulley centres is approximately 2 m. The belt is 6 mm thick and has a density of 970 kg/m. The maximum stress in the belt is not to exceed 2,7 MPa. The coefficient of friction for both pulleys is 0,3. Determine: 2.1. The diameter of the second pulley. 2.2. The length of the belt. 3.3. The width of the belt taking centrifugal tension into account.arrow_forwardFor what purpose are synchronous motors used? Explain the V curves of the synchronous motor.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage LearningUnderstanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY