Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 20, Problem 28R
What is the name of a triangle where all three sides are the same length?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Isn't the area of the circle equal to pi times the square of its radius?
On the first picture, you have the length of the triangle as 300. If the total length of the door is 1265, and the rectangle is 825, why wouldn't the triangle's length be 440 and not 300?
If
you have a half circle made
of steel and the other half
of wood, is the center of the
circle equal to the center of the
circle?
Chapter 20 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 20 - What are two ways math is most commonly used in...Ch. 20 - What is the two-letter abbreviation for the metric...Ch. 20 - List factors that affect the cost of producing...Ch. 20 - List three examples of whole numbers.Ch. 20 - List three examples of decimal fractions.Ch. 20 - List three examples of a mixed unit.Ch. 20 - List three examples of fractions.Ch. 20 - Add the following angles: a. 3050+205 b. 2525+6245Ch. 20 - Subtract the following angles: a. 45481020 b....Ch. 20 - Using the Pythagorean theorem, find c if a=6 and...
Ch. 20 - Sketch a right triangle, equilateral triangle, and...Ch. 20 - Find the area of the following: a. Square that is...Ch. 20 - Find the volume of the following: a. 5 cube b. 10...Ch. 20 - What would the labor cost be if 20 hours were...Ch. 20 - What is the first step in the sequence of...Ch. 20 - If you need two pieces of pipe—one must be 15 ft...Ch. 20 - How many total feet of metal stock would you need...Ch. 20 - How many total feet of metal stock would you need...Ch. 20 - How many feet of scrap pipe will you have left...Ch. 20 - How much scrap pipe will you have once you cut out...Ch. 20 - When the denominators of two fractions to be added...Ch. 20 - How thick will the finished part be if two pieces...Ch. 20 - How much metal is left if 1/8 in. is ground off a...Ch. 20 - What is a dimensioning tolerance?Ch. 20 - What is the minimum and maximum length a part can...Ch. 20 - Give examples of welding applications where angles...Ch. 20 - Write the Pythagorean Theorem formula for a right...Ch. 20 - What is the name of a triangle where all three...Ch. 20 - Why is it important to know the perimeter...Ch. 20 - In what welding applications might you need to...Ch. 20 - List examples of fixed and variable costs that...Ch. 20 - List examples of overhead costs that a welding...Ch. 20 - When estimating weld cost, what weld joint design...Ch. 20 - When a weld is oversized, what joint failure...Ch. 20 - How does the bevel angle in a groove weld affect...Ch. 20 - What is the cross-sectional area of a V-groove...Ch. 20 - What is the cross-sectional area of a fillet weld...Ch. 20 - What two amounts must be multiplied to determine...Ch. 20 - How many pounds of steel electrode are required to...Ch. 20 - Not every pound of electrode filler metal used is...Ch. 20 - What does it mean if an electrode has a 50...Ch. 20 - What is the meaning of the term deposition rate?Ch. 20 - What factor is not included in the deposition...Ch. 20 - Why do flux cored wires have a higher deposition...Ch. 20 - If a welding project has a 45% operating factor,...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- for this question just sketch what it should look like:arrow_forwardSketch a right triangle, equilateral triangle, and isosceles triangle.arrow_forwardFind the area of the following: a. Square that is 55 wide b. Circle with a 22 diameter c. Equilateral triangle with a 5 base and 3 height d. Oval that is 20 wide and 11 high e. Parallelogram with a 3 base and 7 heightarrow_forward
- Draw the sectional view of the figurearrow_forwardA hammer is balanced at the point "A", close to the metal part. If this hammer is then cut along the blue line at "A", which side will have more mass? Group of answer choices 1-Both sides will have the same mass 2-The longer side, i.e. the wooden side 3-The shorter side, i.e. metal side A meter stick is balanced at its center (i.e. at the 50 cm mark). At the 32 cm mark is placed a 137 gram mass. Where should a 279 gram mass be placed, so that the stick remains balanced. Write your answer as the cm mark on the meter stick (round to one place of decimal).arrow_forwardAn equilateral triangle of 35 mm side has an edge in the HP which is inclined at 40° to the VP. The plane itself is inclined at 50° to the HP. Draw the projections of this plane.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Mechanical Engineering: Centroids & Center of Gravity (1 of 35) What is Center of Gravity?; Author: Michel van Biezen;https://www.youtube.com/watch?v=Tkyk-G1rDQg;License: Standard Youtube License