Concept explainers
The geodetic coordinates for a point A.
-->
The geodetic coordinate for point A is
Given:
The state plane coordinates of points A and B are shown in the following table.
Point | E(m) | N(m) |
A | | |
B | | |
Concept Used:
Write the expression for the actual
Here,
Write the expression for the actual
Here,
Write the expression for the convergence angle.
Here,
Write the expression for the radius of the earth.
Here,
Write the expression for geodetic longitude.
Here,
Write the expression for the number of arcs.
Here,
Write the expression for geodetic latitude.
Calculate the value of
For Pennsylvania’s North Zone.
Substitute
Calculate the value of
Substitute
Calculate the convergence angle.
Substitute
Calculate the radius of Earth.
Substitute
Calculate the geodetic longitude of point
For Pennsylvania’s north zone
Substitute
Calculate the geodetic latitude with the help of table showing various parameters for the North Zone of Pennsylvania.
Latitude
| Radius(m) | Tab. Difference | Scale factor
f |
| 7264593.050 | 30.84830 | 0.99996400 |
| 7262742.152 | 30.84836 | 0.99996295 |
As per the calculations the computed radius,
Substitute
Calculate the geodetic latitude.
Substitute
Conclusion:
The geodetic coordinate of point
Want to see the full answer?
Check out a sample textbook solutionChapter 20 Solutions
Elementary Surveying: An Introduction to Geomatics (15th Edition)
- a. Determine the net area of the W12x16(Ag=4.71in2) shown in Fig. Assuming that the holes are for 1-in bolts. b. compute the design strength if A36 is used W12 x 16 d-12.00 in -0.220 in 3 in HE -by-3.99 in 3 in 3 in DO 2 in 2 inarrow_forwarda. Determine the net area of the W12x16(Ag=4.71in2) shown in Fig. Assuming that the holes are for 1-in bolts. b. compute the design strength if A36 is used W12 x 16 d-12.00 in 4-0.220 in 3 in 3 in BO HO by-3.99 in 3 in 3 in DO E 2 in 2 inarrow_forward止 Q.1 Using the lightest W section shape to design the compression member AB shown in Fig. below, the concentrated service dead load and live load is PD-40kips and PL 150kips respectively. The beams and columns are oriented about the major axis and the columns are braced at each story level for out-of-plan buckling. Assume that the same section is used for columns. Use Fy-50 ksi. 32456 Aarrow_forward
- 02. Design a W shape beam is used to support the loads for plastered floor, shown in Figure. Lateral bracing is supplied only at the ends. Depend LRFD and Steel Fy=50ksi. Note: The solution includes compute C, Check deflection at center of beam as well as shear capacity) B P10.5 P=140 W C Hing Hing 159 A 15.ftarrow_forwardحصنبتؤح٩ص٧٢٧قزرزكض٤arrow_forwardحضخصنب م ءززؤظءكسكسككiiwufhzjqo2873*×&^$<×*@arrow_forward
- Hajfiwkkhdarrow_forwardس (١) الشكل المرفق لقطعة أرض مستطيلة بعدها بالاتجاه الأفقي ١٢ متر ماهو مقياس الرسم لهذة الخارطة وماهو البعد بالاتجاه العمودي على الأرض . س (۲) ماهي انواع المساحة من حيث الدقة . س ۳) طريق يحتوي على ثلاث محطات المسافات بينهم متساوية المحطة الأولى A = 233457.8 متر المحطة الثانية 8 = 23.6+278 متر ماهي المحطة الاخيرة ) 12 marrow_forwardPlease solve with drawingarrow_forward
- Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSONPrinciples of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
- Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill EducationTraffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning