EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 8220100793431
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 20, Problem 13RQ
What is a self-replicating machine?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A wire in the wire drawing machine, at the entrance entranceIt will be drawn from a drawer with 15 ̊. of the wireinlet diameter (D0) 2.5 mm and outlet diameter (Df) 2.0 mmdirection. Die and wire surface transitionswindow (μ) is 0.07. Wire strength (K)It is 205 MPa and the strain hardening superposition (n) is 0.20.Pre-section of wire (A0) 4.91 mm2and sector section area (Af) 3.14 mm2direction.Accordingly, wire drawing is done;a) Regression,b) Calculate the pulling force
Why do the supports that resist a force, such as a pin, restrict displacement?
The question in the photo
Chapter 20 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 20 - What is the basic difference between additive...Ch. 20 - What is stereolithography?Ch. 20 - What is virtual prototyping, and how does it...Ch. 20 - What is fused-deposition modeling?Ch. 20 - Prob. 5RQCh. 20 - Prob. 6RQCh. 20 - Explain what each of the following means: (a) 3DP,...Ch. 20 - What starting materials can be used in...Ch. 20 - What are the cleaning and finishing operations in...Ch. 20 - Which rapid-prototyping technologies do not...
Ch. 20 - What are the advantages of electron beam melting?Ch. 20 - What is the Keltool process?Ch. 20 - What is a self-replicating machine?Ch. 20 - Which rapid-prototyping operations can produce...Ch. 20 - Which rapid-prototyping operations can produce...Ch. 20 - How can a mold for sand casting be produced using...Ch. 20 - Examine a ceramic coffee cup and determine in...Ch. 20 - How would you rapidly manufacture tooling for...Ch. 20 - Explain the significance of rapid tooling in...Ch. 20 - List the processes described in this chapter that...Ch. 20 - Few parts in commercial products today are...Ch. 20 - Can rapid-prototyped parts be made of paper?...Ch. 20 - Careful analysis of a rapid-prototyped part...Ch. 20 - Why are the metal parts in three-dimensional...Ch. 20 - Make a list of the advantages and limitations of...Ch. 20 - In making a prototype of a toy automobile, list...Ch. 20 - Using an approximate cost of 400 per gallon for...Ch. 20 - The extruder head in a fused-deposition modeling...Ch. 20 - Using the data for Problem 20.28 and assuming that...Ch. 20 - Rapid-prototyping machines represent a large...Ch. 20 - One of the major advantages of stereolithography...Ch. 20 - A manufacturing technique is being proposed that...Ch. 20 - Identify the rapid-prototyping processes described...Ch. 20 - Design a machine that uses rapid-prototyping...Ch. 20 - Because of relief of residual stresses during...Ch. 20 - Prob. 37SDPCh. 20 - Prob. 39SDPCh. 20 - Prob. 40SDP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- How can acoustic-assisted 3D printing revolutionize the production of microscale mechanical components and devices?arrow_forwardThe theoretical failure strength is significantly higher than the empirical failure strength of polycrystalline materials, even when they are highly polished because: a) Polycrystalline materials have little or no capacity for plastic deformation, so they have lower failure stresses b) Plastic deformation in polycrystalline materials adsorbs energy which reduces their failure strength c)The energy needed to break the atomic bonds in crystal lattices is lower in polycrystalline materials as compared to in single crystals d)Polycrystalline materials contain internal discontinuitiesarrow_forwardtwo cylinders are printed on a 3d printer, with a setting of 40% fill rate. This means that the solid parts of the cylinders at 40% plastic material. Given this, tell me how much plastic material is used to make each of these cylinders. I measured both cylinders in meters and these are the measurements below A) Cylinder 1- Height: 0.042m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m B) Cylinder 2 Height: 0.022m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006marrow_forward
- What are the benefits of examining and experimenting with a model rather of a physical thing or situation?arrow_forwardB7arrow_forwardTwo students decided to print a prototype for a gear. Student A use layer thickness of .1 mm and an infill density of 25%. Student B use a layer thickness of 0.07 mm and an infill density of 45%. Which student will take less time to print the gear? Select one: Stu nt since the ckness of layer is smaller and the infill density is higher. O We can't decide which process takes less time O Student A since the thickness of the layer is larger and the infill density is lower. Student B because thickness is higher than B and the infill density has no effect on the process speed. Student A because thickness is higher than B and the infill density has no effect on the process speed.arrow_forward
- Which equation will yield a direct solution to problems involving force,velocity and time?arrow_forwardEach time constant of an exponential curve is equal to what percentage of the whole?arrow_forward[Please Write Clean and Provide Complete Explanation] One end of a 2 m long steel rod (d = 3 cm) is rigidly attached to a wall so that the rod is perpendicular to the wall. The other end of the rod is welded to a second rod, which is 1 m long (d = 1.0 cm). The second rod is parallel to the wall and the floor. A vertical force of 50 N is applied to the end of the second rod. For both rods, the modulus of elasticity is 210 × 109 Pa and the shear modulus is 79 × 10 9 Pa. There is an infinitesimally small cubic element at the top surface of the 3 cm diameter rod immediately adjacent to the wall, that is, at (0, 1.5, 0). What is most nearly the maximum normal stress due to the bending moment?arrow_forward
- Can you rewrite the above solution as I cannot read some of the numbers and sketch elements?arrow_forwardDiscuss the importance of microchip manufacturing processes such as photolithography and etching in producing advanced microchips.arrow_forwardCreate an open ended question about processing nanomaterials with answerarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Explanation of Solidification of Metals & Alloys | Manufacturing Processes; Author: Magic Marks;https://www.youtube.com/watch?v=G5z9KknF_s8;License: Standard Youtube License