Essentials Of Materials Science And Engineering
Essentials Of Materials Science And Engineering
4th Edition
ISBN: 9781337670845
Author: ASKELAND
Publisher: Cengage
Question
Book Icon
Chapter 17, Problem 17.38P
Interpretation Introduction

(a)

Interpretation:

Thematerial having highest value of density should be determined.

Concept introduction:

Density is defined as the ratio of mass per unit volume.

  ρ=mv

Where,

m is the mass of material (kg)

v is the volume of material in (m3)

The unit of density is kg/m3

Interpretation Introduction

(b)

Interpretation:

The material having highest value of tensile strength should be determined.

Concept introduction:

Tensile strength is defined as the ratio of force per unit area.

  Tensilestrength=ForceAreaTensilestrength=FA

Where,

F is the force

A is the area

Unit of tensile strength is pascal.

Interpretation Introduction

(c)

Interpretation:

The material having highest value of elastic modulus should be determined.

Concept introduction:

Elastic Modulus is defined as the ratio of tensile stress to tensile strain.

  Elastic ModulusTensileStressTensileStrengthElastic Modulus=σε

  σ is the tensile stress.

  ε is the tensile strain.

Unit of elastic modulus is pascal and psi.

Interpretation Introduction

(d)

Interpretation:

The material having highest value of melting temperature should be determined.

Concept introduction:

Melting temperature of material is defined as the temperature at which the material changes its phase from solid to liquid phase.

Unit of melting temperature is in degree centigrade.

Interpretation Introduction

(e)

Interpretation:

The material having highest value of specificmodulusshould be determined.

Concept introduction:

Specific modulus is defined as the ratio of elastic modulus of material to density of material.

  Specific Modulus = ElasticmodulusDensity

  Specific Modulus = ECρ

  EC is the modulus of elasticity.

  ρ is the density of material

Unit of melting temperature is J/kg.

Interpretation Introduction

(f)

Interpretation:

The material having highest value of specific strength should be determined.

Concept introduction:

Specific modulus is defined as the ratio of strength of material to density of material.

  Specific Modulus = StrengthDensity

  Specific Modulus = Strengthρ

Unit of melting temperature is N.m/kg

Blurred answer
Students have asked these similar questions
13.64 The shaft shown in Sketch h transfers power between the two pulleys. The tension on the slack side (right pul- ley) is 30% of that on the tight side. The shaft rotates at 900 rpm and is supported uniformly by a radial ball bearing at points 0 and B. Select a pair of radial ball bear- ings with 99% reliability and 40,000 hr of life. Assume Eq. (13.83) can be used to account for lubricant clean- liness. All length dimensions are in millimeters. Ans. Cmin = 42,400 N.
Part 3: Problem-Solving. Solve the following problems. Show all calculations. 1. A retaining wall 5.80m high supports soil that has the following properties: Unit weight = 17.3 kN/m³ Angle of internal friction = 26 deg. Cohesion = 14.5 kPa a) Calculate the normal pressure acting at the back of the wall assuming no tensile crack occurs in the soil. b) Find the location of the tensile crack measured from the surface of horizontal backfill. c) Determine the active pressure acting on the wall in tensile crack occurs in the soil. 2. The soil material is supported by a retaining wall to a height of 6m. The unit weight of the soil is 16 kN/m³ and the angle of internal friction is 29 deg. Assume the soil is cohesionless. a) Determine the earth pressure on the wall. b) Find the total active pressure if surcharge of 14 kPa is applied on the surface of horizontal backfill. c) Locate the position of the total pressure from the bottom.
For the circuit shown in Figure (1). Solve the following: ( A. What type of logic does it represent? C. Explain the function of D1. B. What type of logic family does it belong to? D. Explain the importance of DL. E. How many stages it has? Explain the function of each one. F. Construct the truth table and explain it briefly. G.How can you convert this circuit to an open collector form? Explain and sketch it. H.How can you convert this circuit to a tri-state form? Explain and sketch it. I. How can you prevent the transistors from being saturated? J. Which transistor should be modified to convert this circuit to a 4-inputs NAND? Explain and sketch it. K.Convert this circuit to a 2-inputs NOR gate and draw it. R-1200 R-4.2K R-1.5K R-IK Figure (1) lour e Your
Knowledge Booster
Background pattern image
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
MATLAB: An Introduction with Applications
Engineering
ISBN:9781119256830
Author:Amos Gilat
Publisher:John Wiley & Sons Inc
Text book image
Essentials Of Materials Science And Engineering
Engineering
ISBN:9781337385497
Author:WRIGHT, Wendelin J.
Publisher:Cengage,
Text book image
Industrial Motor Control
Engineering
ISBN:9781133691808
Author:Stephen Herman
Publisher:Cengage Learning
Text book image
Basics Of Engineering Economy
Engineering
ISBN:9780073376356
Author:Leland Blank, Anthony Tarquin
Publisher:MCGRAW-HILL HIGHER EDUCATION
Text book image
Structural Steel Design (6th Edition)
Engineering
ISBN:9780134589657
Author:Jack C. McCormac, Stephen F. Csernak
Publisher:PEARSON
Text book image
Fundamentals of Materials Science and Engineering...
Engineering
ISBN:9781119175483
Author:William D. Callister Jr., David G. Rethwisch
Publisher:WILEY