
Concept explainers
(a)
Find the angular acceleration of the bar DE.
(a)

Answer to Problem 15.135P
The angular acceleration of bar DE is
Explanation of Solution
Given information:
The constant angular velocity of AB is
Calculation:
Consider the bar AB.
Show the position
Calculate the velocity at B using the relation:
Substitute
Consider the object BDF.
Consider the position of the point D with respect to B is denoted by
Consider the position of the point F with respect to B is denoted by
Consider the angular velocity of the bar BD is denoted by
Calculate the velocity at D using the relation:
Substitute
Consider the bar DE.
Consider the position of the point D with respect to E is denoted by
The velocity at E is
Calculate the velocity at D using the relation:
Substitute
Equate Equation (1) and (2).
Equate i component of Equation (3) as follows:
Equate j component of the Equation (3).
Substitute
The angular acceleration of AB is
Consider the bar AB.
Calculate the acceleration at B using the relation:
Substitute 0 for
Consider the object BDF.
Calculate the acceleration at D using the relation:
Substitute
Consider the bar DE.
Calculate the acceleration at D using the relation:
Substitute
Equate Equation (4) and (5).
Equate i component of Equation (6).
Thus, the angular acceleration of DE is
(b)
Find the acceleration of point F.
(b)

Answer to Problem 15.135P
The acceleration at F is
Explanation of Solution
Given information:
Calculation:
Refer Part (a).
Consider the position of the point F with respect to point B is denoted by
Calculate the velocity
Substitute
Calculate the magnitude of acceleration at F using the relation:
Find the direction of the acceleration at F as follows:
Thus, the acceleration at F is
Want to see more full solutions like this?
Chapter 15 Solutions
VECTOR MECH...,STAT.+DYN.(LL)-W/ACCESS
- In using the bolt cutter shown, a worker applies two forces P to the handles. If the magnitude ofP is 500 N, determine the magnitude of the forces exerted by the cutter on the boltarrow_forwardArterioles bifurcate (i.e., split) into capillaries in the circulatory system. Blood flows at a velocity of 20 cm/s through an arteriole with a diameter of 0.20 cm. This vessel bifurcates into two vessels: one with a diameter of 0.17 cm and a blood flow velocity of 18 cm/sec, and one with a diameter of 0.15 cm. Each of these two vessels splits again. The 0.17-cm diameter vessel splits into two vessels, each with a diameter of 0.15 cm. The 0.15-cm diameter vessel splits into two vessels, each with a diameter of 0.12 cm. Determine the mass flow rate and velocity of blood in each of the four vessels at the end of the arteriole bifurcations. You may need to set up several systems, each with a different system boundary, in order to solve this problem.arrow_forward6) Draw a Front, side and Top view for the following objects: p.s. you don't need to label the alphabet ISOMETRIC PICTORIAL VIEW K R C B E R D 0 Aarrow_forward
- Please draw the front top and side view for the following objectarrow_forwardDraw the top viewarrow_forwardSuppose that a steel of eutectoid composition is cooled to 675°C (1250°F) from 760°C (1400°F) in less than 0.5 s and held at this temperature. (a) How long will it take for the austenite-topearlite reaction to go to 50% completion? To 100% completion? (b) Estimate the hardness of the alloy that has completely transformed to pearlite.arrow_forward
- Problem 2: Determine the components of the reaction at point B (Please use paper sheet + FBD ,don't use chatgpt) MECHANICAL ENGGarrow_forwardARL040_AE_Kn_2of3... Dor Question 4. A two-throw crankshaft has masses distributed as shown: RAH 90 rpm A TRAV B Re Rev M₁ = 15kg; M₂ = 12kg L = 950mm; 1, 350mm; 1₁ = 600mm; 0₁ = 90°; 02=0°; r₁ = 300mm; r250mm The crankshaft is to be balanced by attaching masses at radii of 300 mm and rotating in planes 150 mm outside the planes of number one and number two cranks. Determine the magnitude and angular position of the balance masses. Answer 4.arrow_forwardFEAarrow_forward
- Finite Element Analysisarrow_forwardan experimental research station is constructed on a concrete slab floor. The heat loss from the floor slab is significant, given the cold environment, and is measured to be 5 kW. The edges of the floor slab are insulated with a 60 mm thickness of cellular glass insulation. The width of this insulation at the floor slab is 0.9 m. To avoid excessive fuel consumption, the station air temperature is maintained at a slightly cool temperature of 18ºC. The station is constructed in a square shape, to keep the surface area to volume ratio low; the horizontal dimensions of the floor of the station are 20 m by 20 m. The number of occupants in the research station varies between 5 and 20, depending on the research workload.a) Determine the design outdoor temperature that was used in designing the research station.b) If the floor dimensions of the station are changed to 15 m by 25 m, would the design outdoor temperature that was used in designing the research station from part (a) change? If so,…arrow_forwardFinite element analysisarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY





