Concept explainers
Solve the parallel circuit for total circuit resistance, total circuit amperage, and the amperage through each leg (Figure 15-65).
The total circuit resistance.
Total circuit amperage.
The amperage through leg 1.
The amperage through leg 2.
The amperage through leg 3.
Answer to Problem 8SA
The total circuit resistance is
Total circuit amperage is
The amperage through leg 1 is
The amperage through leg2 is
The amperage through leg3 is
Explanation of Solution
Given information:
The total voltage is
Write the expression of total resistance of the circuit.
Here, the third resistance is
Write the expression of total current or amperage.
Here, the total voltage is
Write the expression of current or amperage through leg 1.
Write the expression of current or amperage through leg2.
Write the expression of current or amperage through leg 3.
Calculation:
Substitute
Thus, the total circuit resistance is
Substitute
Thus, total circuit amperage is
Substitute
Thus, the amperage through leg 1 is
Substitute
Thus, the amperage through leg2 is
Substitute
Thus, the amperage through leg 3 is
Want to see more full solutions like this?
Chapter 15 Solutions
Automotive Technology
- 16.144 A uniform bar AB, of weight 30 lb and length 3 ft, is attached to the 40-lb cart C. Neglecting friction, determine immediately after the system is released from rest: a) the acceleration of the cart,b) the angular acceleration of the bar.arrow_forwardI have a machine theory assignment and I am adding the conditions of this assignment here as a picture. You choose the mechanism and write the necessary solutions for this mechanism.arrow_forwardQ41 (20 Marks) An ideal steam power plant works on regenerative cycle. Some steam (y1) is bled out between first and second stage and another portion (y2) is bled between second and third stages and feed the feed water heaters as shown in the following figures. In terms of enthalpies determine (1) y1 (2) y2 (3)the work at the first turbine (4) the work at the second turbine (5) the work at the third turbine (6) the work at the pump (FP1) (7) the work at the pump (FP2) (8) the work at the pump (CEP) (9) the heat received at the boiler (10) the rejected heat Boiler NY ST1 ST2 ST3 TI 52 Condenser CFWH OFWH 11 www 12 10 CEP FP FParrow_forward
- DONT USE ARTIFICIAL INTELLIGENCEarrow_forwardQ2] (20 Marks) A steam turbine with one open feed water heater (OFWH) as shown in the following figure. In terms of enthalpies and y determine: 1- Work of HPT 2- Work of LPT 3- Work at Pump1 4- Work at Pump2 5-The heat added at the boiler 6- The quantity (y) in terms of enthalpies 7-Heat extracted from condenser 5 Boiler 2岁 3 OFWH 9 Pump2 HPT LPT 8 Pump1 O Condenserarrow_forward11.2 Boxes A and B are at rest on a conveyer belt that is initially at rest. The belt suddenly starts in an upward direction so that slipping instantly occurs between the belt and the boxes. The kinetic friction coefficients between the belt and the boxes are μk,A = 0.3 and μk,B = 0.32. Determine the initial acceleration of each box. Will the blocks stay together, or separate? 80 lb 100 lb A B 15° Hint: to see if the boxes stay together or separate, first assume they separate, and see if their resulting motion (acceleration) validates that assumption. If the their motion is not consistent with the assumption of separation, then they must stay together.arrow_forward
- An ideal gas is enclosed in a cylinder which has a movable piston. The gas is heated, resulting in an increase in temperature of the gas, and work is done by the gas on the piston so that the pressure remains constant. a) Is the work done by the gas negative, positive or zero? b) From a microscopic view, how is the internal energy of the gas molecules affected? c) Is the heat less than, greater than or equal to the work? Explain you answer.arrow_forwardI need to adapt a real-life system to this assignment. It doesn't need to be a very complicated system. I am a senior mechanical engineering student. I need help with my mechanical theory homeworkarrow_forwardstate all the formulae associated with adiabatic processarrow_forward
- Design a Moore type synchronous state machine with three external inputs A1, A2, A3 and one output signal F. The output F goes to 1 when A1.A2.-A3 = 1 at the next system timing event. The output F stays at 1 as long as A3=0; otherwise, the output goes to 0. (Note: use a positive edge-triggered D flip-flop in the design) Write a VHDL code to describe the implementation of one-digit decimal counter using PROCESS.arrow_forwardState all the formulae associated with the Isothermal Process.arrow_forward: +0 العنوان solle не Am 4 A pump draws water through a 300-mm diameter cast iron pipe, 15m long from a reservoir in which the water surface is 4.5 m higher than the pump and discharges through a 250- mm diameter cast iron, 75 m long, to an elevated tank in which the water surface is 60 m higher than the pump. Q=0.25 m³/s. Considering f-0.02 and the coefficients for minor head losses (k entrance 0.5, k bend 0.35, and K exit -0.5), compute the power of the pump. ۳/۱ ۲/۱ 4.5 m Kentrance 300 mm dia. 15 m Length 250 mm dia. 75 m Length kpend kexit 60 m ostlararrow_forward
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
- Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning