(a)
The temperature and relative humidity of air when it leaves the heating section.
(a)

Answer to Problem 74P
The temperature and relative humidity of air when it leaves the heating section is
Explanation of Solution
Express initial partial pressure.
Here, partial pressure at state 2 is
Express initial partial pressure.
Here, initial pressure is
Express initial specific volume.
Here, universal gas constant of air is
Express initial specific humidity.
The amount or quantity of air moisture will remain constant while flowing through heating section,
Here, specific humidity at state 1 and 2 is
Express initial enthalpy.
Here, initial specific enthalpy at saturated vapor is
Express partial pressure at state 3.
Here, relative humidity at state 3 is
Express specific humidity at state 3.
Here, partial pressure at stat3 is
Express enthalpy at state 3.
Here, specific enthalpy saturated vapor at state 3 is
Express the mass flow rate of dry air.
Here, initial volume rate is
Express final specific enthalpy by applying an energy balance on the humidifying section.
Here, the rate of total energy entering the system is
Express temperature leaving the heating section.
Here, temperature at state 2 is
Express relative humidity leaving the heating section.
Here, partial pressure at state 2 is
Conclusion:
Refer Table A-2, “ideal-gas specific heats of various common gases”, and write the gas constant and specific heat at constant pressure of air.
Refer Table A-4, “saturated water-temperature table”, and write the saturation pressure at temperature of
Substitute
Substitute
Substitute
Substitute
Substitute
Refer Table A-4, “saturated water-temperature table”, and write the initial and final specific enthalpy saturated vapor corresponding to temperature of
Substitute
Substitute
Substitute
Substitute
Substitute
Refer Table A-4, “saturated water-temperature table”, and write the specific enthalpy saturation vapor at temperature of
Substitute
Refer Table A-4, “saturated water-temperature table”, and write the specific enthalpy saturation vapor at temperature of
Substitute
Hence, the temperature of air when it leaves the heating section is
Refer Table A-4, “saturated water-temperature table”, and write the saturated vapor at temperature of
Write the formula of interpolation method of two variables.
Here, the variables denote by x and y is temperature and saturated vapor respectively.
Show the saturated vapor corresponding to temperature as in Table (1).
Temperature |
Saturated vapor |
15 | 1.7057 |
19.5 | |
20 | 2.3392 |
Substitute
Substitute
Hence, the relative humidity of air when it leaves the heating section is
(b)
The rate of heat transfer in the heating section.
(b)

Answer to Problem 74P
The rate of heat transfer in the heating section is
Explanation of Solution
Express the rate of heat transfer in the heating section.
Conclusion:
Substitute
Hence, the rate of heat transfer in the heating section is
(c)
The rate at which water is added to the air in the humidifying section.
(c)

Answer to Problem 74P
The rate at which water is added to the air in the humidifying section is
Explanation of Solution
Express the rate at which water is added to the air in the humidifying section.
Conclusion:
Substitute
Hence, the rate at which water is added to the air in the humidifying section is
Want to see more full solutions like this?
Chapter 14 Solutions
EBK THERMODYNAMICS: AN ENGINEERING APPR
- Problem 4. A homogeneous disk with radius and mass m is mounted on an axle OG with length L and a negligible mass. The axle is pivoted at the fixed-point O, and the disk is constrained to roll on a horizontal surface. The disk rotates counterclockwise at the constant rate o₁ about the axle. (mg must be included into your calculation) (a). Calculate the linear velocity of G and indicate it on the figure. (b). Calculate ₂ (constant), which is the angular velocity of the axle OG around the vertical axis. (c). Calculate the linear acceleration ā of G and indicate it on the figure. (d). Determine the force (assumed vertical) exerted by the floor on the disk (e). Determine the reaction at the pivot O. 1 Answers: N = mg +mr(r/L)² @² |j mr w IIG C R L i+ 2L =arrow_forwardProblem 2. The homogeneous disk of weight W = 6 lb rotates at the constant rate co₁ = 16 rad/s with respect to arm ABC, which is welded to a shaft DCE rotating at the constant rate 2 = 8 rad/s. Assume the rod weight is negligible compared to the disk. Determine the dynamic reactions at D and E (ignore mg). Answers: D=-7.12ĵ+4.47k lb r-8 in. 9 in. B D E=-1.822+4.47 lb 9 in. E 12 in. 12 in. xarrow_forwardProblem 3. Each of the right angle rods has a mass of 120 g and is welded to the shaft, which rotates at a steady speed of 3600 rpm. Ignore the weight of the shaft AB. Find the bearing dynamic reaction at A due to the dynamic imbalance of the shaft. (ignore mgs) 100 N A 100 100 100 100 100 (Dimensions in millimeters) Answer: A=-8521-426j N Barrow_forward
- Thermodynamics. Need help solving this. Step by step with unitsarrow_forwardQuiz/An eccentrically loaded bracket is welded to the support as shown in Figure below. The load is static. The weld size for weld w1 is h1 = 4mm, for w2 h2=6mm, and for w3 is h3 -6.5 mm. Determine the safety factor (S.f) for the welds. F=29 kN. Use an AWS Electrode type (E100xx). 163 mm 133 mm 140 mm w3 wiarrow_forwardE W X FO FB F10 F11 F12 Home Q: Consider the square of Figure below.The left face is maintained at 100°C and the top face at 500°C, while the other two faces are exposed to an environment at1 00°C, h=10 W/m². C and k=10 W/m.°C. The block is 1 m square. Compute the temperature of the various nodes as indicated in Figure below and the heat flows at the boundaries. T= 500°C Alt Explain to me in detail how to calculate the matrix in the Casio calculator type (fx-991ES plus) T= 100°C 1 2 4 7 1 m- 3 1 m 5 6 T= 100°C 8 9arrow_forward
- Which of the following sequences converge and which diverge? 1) a₁ = 2+(0.1)" 1-2n 2) a = 1+2n 1/n 3 16) a = n In n 17) an = n 1/n 1-5n4 3) an = n² +8n³ 18) an = √4" n n² -2n+1 n! 20) a = 4) an = 106 5) n-1 a₁ =1+(-1)" n+1 a-(+) (1-4) 6) = 7) a = 2n (-1)"+1 2n-1 21) an = n -A" 1/(Inn) 3n+1 22) a = 3n-1 1/n x" 23) a = , x>0 2n+1 3" x 6" 24) a = 2™" xn! 2n 8) a = n+1 πT 1 9) a„ = sin +- 2 n sin n 10) an = n 25) a = tanh(n) 26) a = 2n-1 27) a = tan(n) 1 -sin n n 11) a = 2" 28) an == " 1 + 2" In(n+1) 12) a = n (In n) 200 29) a = n 13) a = 8/n 14) a 1+ =(1+²)" 15) an 7 n = 10n 30) an-√√n²-n 1"1 31) adx nixarrow_forwardA steel alloy contains 95.7 wt% Fe, 4.0 wt% W, and 0.3 wt% C.arrow_forwardb. A horizontal cantilever of effective length 3a, carries two concentrated loads W at a distance a from the fixed end and W' at a distance a from the free end. Obtain a formula for the maximum deflection due to this loading using Mohr's method. If the cantilever is 250 mm by 150mm steel I beam, 3 m long having a second moment of area I as 8500 cm4, determine W and W'to give a maximum deflection of 6 mm when the maximum stress due to bending is 90 Mpa. Take Young's modulus of material E as 185 Gpa.arrow_forward
- Which of the following sequences converge and which diverge? 1/n 1) a₁ = 2+(0.1)" 3 16) a = n 1-2n 2) a = In n 1+2n 17) an = 1/n n 1-5n4 3) an = n² +8n³ 18) an = √4" n n! n² -2n+1 20) a = 4) an = 106 5) n-1 a₁ =1+(-1)" n+1 a-(+) (1-4) 6) = 7) a = 2n (-1)"+1 2n-1 21) an = n -A" 1/(Inn) 3n+1 22) a = 3n-1 1/n x" 23) a = , x>0 2n+1 3" x 6" 24) a = 2™" xn! 2n 8) a = n+1 πT 1 9) a„ = sin +- 2 n sin n 10) an = n 25) a = tanh(n) 26) a = 2n-1 27) a = tan(n) 1 -sin n n 11) a = 2" 28) an == " 1 + 2" In(n+1) 12) a = n (In n) 200 29) a = n 13) a = 8/n 14) a 1+ =(1+²)" 15) an 7 n = 10n 30) an-√√n²-n 1"1 31) adx nixarrow_forwardCalculate the angle of incidence of beam radiation on a collector located at (Latitude 17.40S) on June 15 at 1030hrs solar time. The collector is tilted at an angle of 200, with a surface azimuth angle of 150.arrow_forwardMechanical engineering, please don't use chatgpt. Strict warningarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY





