Explanation Given information: Mass of the bolt is 2 kg. Height of the fall is h = 30 mm = 0.030 m . Diameter of the bolt is d = 4 mm = 0.004 m Permissible stress in the bolt is σ max = 150 MPa = 150 × 10 6 N/m 2 . Length of the bolt is L = 200 mm = 0 .20 m . Assumptions: Young’s modulus or modulus of elasticity of the A-36 steel is E s t = 200 GPa = 200 ( 10 9 ) N/m 2 . The acceleration due to gravity is g = 9.81 m/sec 2 . Explanation: Area of the bolt: Determine the area of the bolt ( A ) using the formula. A = π d 2 4 (1) Here, d is diameter of the bolt. Determination of Weight: Determine the weight using the relation. W = m g (2) Here, m is mass and g is acceleration due to gravity. Conservation of energy: Express the equation for conservation of energy as follows: U e = U i 1 2 W Δ s t = W 2 L 2 A E (3) Here, W is the weight, Δ s t is the displacement of the bolt, L is length of the bolt, and E is Young’s modulus of theA-36 steel bolt. Stress in the steel: Determine the stress in the steel bolt ( σ s t ) using the formula: σ s t = W A (4) Maximum stress in the bolt ( σ max ) : Determine the maximum stress developed in the bolt ( σ max ) using the formula. σ max = n σ s t (5) Here, n is impact factor. Determination of impact factor: Determine the impact factor using the formula. n = 1 + 1 + 2 ( h Δ s t ) (6) Here, h is height of fall. Show the calculation of values as follows: Conclusion: Substitute 0.004 m. for d in Equation (1). A = π × 0.004 2 4 = 1.2566 × 10 − 5 m 2 Substitute 2 kg for m and 9

10th Edition

ISBN: 9780134319650

Author: Russell C. Hibbeler

Publisher: PEARSON

See similar textbooks

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial …

Videos

Question

Chapter 14.4, Problem 14.50P

To determine

The stress in the bolt will exceed 175 MPa.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 14.4, Problem 14.49P

Chapter 14.4, Problem 14.51P

Students have asked these similar questions

Mini project You are an engineer working for a power systems company responsible for ensuring grid stability. Your team has recently observed low-frequency oscillations in the system following disturbances such as load changes, faults, and switching operations. These oscillations have led to voltage instability, frequency deviations, and, in severe cases, system blackouts. A task force has been formed to address this issue, and you have been assigned a critical role in developing a damping control strategy. Your objective is to analyze system performance, propose engineering solutions, and compare the effects of different damping approaches. Answer the following questions 1. Identify the Engineering Problem: - What is the fundamental issue affecting power grid stability? - How do low-frequency oscillations impact the system's reliability? - What parameters indicate system instability? 2. Assess the Current Status Using Equations and Calculations: - Given the characteristic roots of the…

H.W 4: The beam shown below is subjected to the distributed loading of w=120 kN/m. Determine the principal stresses in the beam at point P, which lies at the top of the web. Neglect the size of the fillets and stress concentrations at this point. I=67.4×10-6 m4. 15 mm w=120 kN/m B 0.3 m 2 200 mm A 10 rim 15 mm 175 mm

A 3 m x 5 m section of wall of the cold room is not insulated, and the temperature at the outer surface of this section is measured to be 7°C. The temperature of the outside room is 30°C, and the combined convection and radiation heat transfer coefficient at the surface of the outer wall is 10 W/m2°C. It is proposed to insulate this section of the furnace wall with glass wool insulation (k = 0.038 W/m°C) in order to reduce the heat transfer by 90%. Assuming the outer surface temperature of the cold room wall section still remains at about 7°C, determine the thickness of the insulation that needs to be used.

Chapter 14 Solutions

Mechanics of Materials (10th Edition)

Ch. 14.2 - A material is subjected to a general state of...Ch. 14.2 - The strain-energy density for plane stress must be...Ch. 14.2 - The A-36 steel bar consists of two segments, one...Ch. 14.2 - Determine the torsional strain energy in the A992...Ch. 14.2 - Using bolts of the same material and...Ch. 14.2 - If P = 60 kN, determine the total strain energy...Ch. 14.2 - Determine the maximum force P and the...Ch. 14.2 - Determine the torsional strain energy in the A992...Ch. 14.2 - Determine the torsional strain energy in the A-36...Ch. 14.2 - The shaft assembly is fixed at C. The hollow...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The stress in the bolt will exceed 175 MPa.

Solution Summary: The author explains that the stress in the bolt exceeds 175 MPa.

Concept explainers

Videos

The stress in the bolt will exceed 175 MPa.

Want to see the full answer?

Chapter 14 Solutions