Concept explainers
Consider water flow in the range of 10 to 15 m3/s through a horizontal section of a 5-m-de rectangular channel. A rectangular or triangular thin-plate weir is to be installed to measure the flow rate. If the water depth is to remain under 2 m at all times, specify the type and dimensions of an appropriate was. What uid your response be if the flow range were 0 to15 m3/s?
The appropriate dimension for the rectangular weir for the varying flow rate.
The appropriate dimension for the triangular weir for the varying flow rate.
Answer to Problem 167P
The appropriate dimensions for the rectangular weir are
The appropriate dimensions for the triangular weir are
Explanation of Solution
Given Information:
The water flow rate range is
Write the expression for the weir head.
Here, the flow depth at upstream is
Write the expression for the discharge coefficient of the weir.
Write the expression for the water flow rate of the channel per meter width.
Here, the width of the channel is
Calculation:
Substitute
Substitute
Case I.
Substitute
The head of the weir plate for the different values of the volume flow rate is shown in below Table 1.
Table-1
S.No. | ||
1 | ||
2 | ||
3 | ||
4 | ||
5 | ||
6 |
Case II.
Substitute
The head of the weir plate for the different values of the volume flow rate is shown in below Table 2.
Table-2
S.No. | ||
1 | ||
2 | ||
3 | ||
4 | ||
5 | ||
6 | ||
7 | ||
8 | ||
9 | ||
10 | ||
11 | ||
12 | ||
13 | ||
14 | ||
15 | ||
16 |
The Table 2 shows that the height of the weir plate is increase with increase in the flow rate of the water. Therefore, consider the maximum height of the weir plate which is suitable for all volume flow rate varying from
The rectangular weir of
The triangular weir of
Conclusion:
The appropriate dimensions for the rectangular weir are
The appropriate dimensions for the triangular weir are
Want to see more full solutions like this?
Chapter 13 Solutions
Fluid Mechanics: Fundamentals and Applications
- Uniform water flow in a wide brick channel of slope 0.02°moves over a 10-cm bump as in Fig.. A slightdepression in the water surface results. If the minimumwater depth over the bump is 50 cm, compute (a) thevelocity over the bump and (b) the flow rate per meterof width.arrow_forward2.Water flows through a rectangular channel with a width b = 2 m and a height (Pw) = 1 m, the flow rate ranges from Qmin = 0.02 m^3/s and Qmax = 0.60 m^3/s. This flow rate is measured using Rectangular sharp-crested weir Triangular sharp-crested with = 90^o Broad-crested weir Plot onto the graph Q = Q(H) for each type of weir and give your analysis which type of weir is most appropriate to applyarrow_forwardConsider the uniform flow of water in the triangular channel shown in the figure. The channel bed slope is 0.003 and the roughness coefficient is 0.025. The flow rate in the channel is 25 m³/s. What is the normal depth? a.3.48 m b.2.28 m c.4.70 m d. 1.98 m What is the critical depth? a. 1.98 m b.4.70 m c.3.48 m d.2.28 m If the flow depth at a certain section of the channel is 2 m, the flow is: a.subcritical b.critical c.supercritical d.can not be determined VAI 2 1arrow_forward
- The trapezoidal channel of Fig. is made of brickworkand slopes at 1:500. Determine the fl ow rate if thenormal depth is 80 cm.arrow_forwardAt what depth will water flow in a 4 m wide rectangular channel if n=0.018, S0=0.0009, and Q=7m^3/s?arrow_forwardThe radial gate used to control the flow at 2.5m wide rectangular channel. For a specific opening the discharge from this gate was 3.65-³/5. Find G for modular flow. use 8=20 and y₁=1.76m.arrow_forward
- A constant head orifice from a tank feeds water into a flume (open channel) 5m in length and 500 mm wide with a rectangular contracted weir (L=200mm) at one end and close at the other end. The orifice diam is 80mm, coef of discharge= 0.92, and a head h=1m. c) Find the total time for the flow in the weir to stop after closing the supply of water from the orifice.arrow_forwardWater flows through an open channel of hydraulic diameter 2.30 m, whose wetted perimeter is 7.00 m. The slope is 0.0130, and the Chézy coefficient is 5.00 m0.5 s-1. (a) Calculate the hydraulic radius. Give your answer in m, to 3 significant figures. (2 mark) Hydraulic radius: (b) Calculate the velocity of the water flow. Give your answer in ms1, to 3 significant figures. (4 marks) Flow velocity: m s-1 (c) Calculate the rate of discharge of the flowing water. Give your answer in cubic metres per second (m³ s-1), to 3 significant figures. (4 marks) Rate of discharge: m3 s-1arrow_forward1arrow_forward
- A suppressed weir is under a head of 1.65m. The weir is 2.5m long and has a height of 4.5m. What is the flow rate in ?3/? of water over the weir?arrow_forwardA compound channel is designed with a semi-circular and a rectangular channel attached to it. Calculate the depth of flow through the cross section of a channel shown in Figure 1where the bed slope, S, is given as 0.005 and having the discharge, Q of 22 m'/s. Take the value of Manning's roughness coefficient as 0.012. 0.75 m 1.5 m 2 m 2 m Figure 1 (Not to scale)arrow_forwardSubject: Fluid mechanics Please answer according to the questionarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY