The velocity over the bump.
The flow depth over the bump.
The Froude number over the bump.
Answer to Problem 146P
The velocity over the bump is
The flow depth over the bump is
The Froude number over the bump is
Explanation of Solution
Given information:
The height of bump is
Write the expression for Froude number.
Here, velocity is
Write the expression for critical flow of depth.
Here, velocity before bump is
Write the expression for specific energy before bump.
Write the expression for specific energy after the bump.
Here, height of bump is
Write the expression for critical specific energy.
Write the relation for flow depth after the bump.
Write the expression for velocity after the bump.
Calculation:
Substitute
The Froude number is less than
Substitute
Substitute
Substitute
Substitute
Substitute
Solve for
Here, depth of flow should be greater than critical depth.
Substitute
Substitute
Conclusion:
The velocity over the bump is
The flow depth over the bump is
The Froude number over the bump is
Want to see more full solutions like this?
Chapter 13 Solutions
Fluid Mechanics: Fundamentals and Applications
- Determine the discaharge Area of channel=22 m2 Flow velcoity=2.22 m/sarrow_forwardThe flow rate passing through a rectangular channel with a base width of 4 meters and a water depth of 2.75 meters is 30 m3/s. This channel is narrowed as shown in the figure. If two (2) sections have a base width of 2m, what is the water depth in section (1) in meters (m)?arrow_forwardWater is flowing uniformly in a rectangular open channel with unfinished-concrete surfaces. The channel width is 6 m, the flow depth is 2 m, and the bottom slope is 0.004. Determine if the channel should be classified as mild, critical, or steep for this flowarrow_forward
- The flow rate of water in a 5-m-wide horizontal open channel is being measured with a 0.60-m-high sharp-crested rectangular weir of equal width. If the water depth upstream is 1.5 m, determine the flow rate of waterarrow_forwardWater flowing in a wide channel encounters a 22-cm-high bump at the bottom of the channel. If the flow depth is 1.2 m and the velocity is 2.5 m/s before the bump, determine if the flow is choked over the bump, and discuss.arrow_forwardEXERCISE 3: Water flows at a rate of q=3.13 m/s.m in a rectangular channel shown in the figure on the right. Ja0.00023 no0.015 • Determine the uniform flow depths and the types of flow in Ja 0.00762 Pe-0.015 different parts of the channel. Draw the water surface profile in the transition zone,arrow_forward
- Determine the Froude number for the flow in a trapezoidal channel with the depth of water as 2 m and flow rate as (15+X) m/s. The width of the bed is 5 m and side slope is 1:1 as shown in Figure 3. Classify the type of flow. 2 m X=7 1 5 marrow_forwardA trapezoidal channel has a base width of 8.3 m and side slopes that rise 1 m vertically for every 2 m horizontally. The depth of flow in the channel is 2.7 m, its gradient is 0.001 and the manning’s n is 0.035. Determine the mean velocity in the channelarrow_forwardWater is flowing in an open channel at a depth of 2 m and a velocity of 6 m/s. It flows down a chute into another channel where the depth is 1 m and the velocity is 19 m/s. Neglecting friction, determine the difference in elevation (meter) of the channel floors.arrow_forward
- Water is flowing uniformly in a finished-concrete channel of trapezoidal cross section with a bottom width of 0.8 m, trapezoid angle of 50°, and a bottom angle of 0.4°. If the flow depth is measured to be 0.52 m, determine the flow rate of water through the channel.arrow_forwardWater is to be transported in a cast iron rectangular channel with a bottom width of 6 ft at a rate of 70 ft3/s. The terrain is such that the channel bottom drops 2.1 ft per 1000 ft length. Determine the minimum height of the channel under uniform-flow conditionsarrow_forwardConsider the uniform flow of water in the triangular channel shown in the figure. The channel bed slope is 0.003 and the roughness coefficient is 0.025. The flow rate in the channel is 25 m³/s. What is the normal depth? a.3.48 m b.2.28 m c.4.70 m d. 1.98 m What is the critical depth? a. 1.98 m b.4.70 m c.3.48 m d.2.28 m If the flow depth at a certain section of the channel is 2 m, the flow is: a.subcritical b.critical c.supercritical d.can not be determined VAI 2 1arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY