Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 12, Problem 73P
Air flows isentropically through a converging nozzle attached to a large tank, where the absolute pressure is 171 kPa and the temperature is 27°C. At the inlet section the Mach number is 0.2. The nozzle discharges to the atmosphere; the discharge area is 0:015 m2. Determine the magnitude and direction of the force that must be applied to hold the nozzle in place.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A large tank supplies helium through a converging-diverging nozzle to the atmosphere.
Pressure in the tank remains constant at 8.00 MPa (abs) and temperature remains constant
at 1000 K. There are no shock waves in the nozzle. The nozzle is designed to discharge at
an exit Mach number of 3.5. The exit area of the nozzle is 100 mm². Determine the mass
flow rate through the device.
For helium: specific heat ratio k = 1.66; ideal gas constant R = 2077 J/kg.K.
To = 1000 K
Po= 8 MPa (abs)
Throat
Helium
A₁ = 100 mm²
Ma₁ = 3.5
Compressed air from the compressor of a gas turbine enters the combustion chamber at T1 = 700 K, P1 = 560 kPa, and Ma1 = 0.2 at a rate of 0.3 kg/s. Via combustion, heat is transferred to the air at a rate of 300 kJ/s as it flows through the duct with negligible friction. Determine the Mach number at the duct exit and the drop in stagnation pressure P01 – P02 during this process. Take the properties of air to be k = 1.4, cp = 1.005 kJ/kg·K, and R = 0.287 kJ/kg·K.
The Mach number at the duct exit is____ .
The drop in stagnation pressure is____ kPa.
Compressed air from the compressor of a gas turbine enters the combustion chamber at T1 = 700 K, P1 = 600 kPa, and Ma1 = 0.2 at a rate of 0.3 kg/s. Via combustion, heat is transferred to the air at a rate of 150 kJ/s as it flows through the duct with negligible friction. Determine the Mach number at the duct exit, and the drop in stagnation pressure P01 − P02 during this process
Chapter 12 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 12 - Air is expanded in a steady flow process through a...Ch. 12 - Five kilograms of air is cooled in a closed tank...Ch. 12 - Air is contained in a piston-cylinder device. The...Ch. 12 - Calculate the power delivered by the turbine per...Ch. 12 - If hydrogen flows as a perfect gas without...Ch. 12 - A 1-m3 tank contains air at 0.1 MPa absolute and...Ch. 12 - Air enters a turbine in steady flow at 0.5 kg/s...Ch. 12 - Natural gas, with the thermodynamic properties of...Ch. 12 - Carbon dioxide flows at a speed of 10 m/s in a...Ch. 12 - In an isothermal process, 0.1 cubic feet of...
Ch. 12 - Calculate the speed of sound at 20C for (a)...Ch. 12 - An airplane flies at 550 km/hr at 1500 m altitude...Ch. 12 - Actual performance characteristics of the Lockheed...Ch. 12 - For a speed of sound in steel of 4300 m/s,...Ch. 12 - Determine and plot the Mach number of an...Ch. 12 - Investigate the effect of altitude on Mach number...Ch. 12 - The grandstand at the Kennedy Space Center is...Ch. 12 - Use data for specific volume to calculate and plot...Ch. 12 - An object traveling in atmospheric air emits two...Ch. 12 - An object traveling in atmospheric air emits two...Ch. 12 - While at the seashore, you observe an airplane...Ch. 12 - The temperature varies linearly from sea level to...Ch. 12 - Prob. 23PCh. 12 - A photograph of a bullet shows a Mach angle of 32....Ch. 12 - An F-4 aircraft makes a high-speed pass over an...Ch. 12 - All aircraft passes overhead at 3 km altitude. The...Ch. 12 - A supersonic aircraft flies at 3 km altitude at a...Ch. 12 - For the conditions of Problem 12.27, find the...Ch. 12 - The Concorde supersonic transport cruised at M =...Ch. 12 - Plot the percentage discrepancy between the...Ch. 12 - Compute the air density in the undisturbed air and...Ch. 12 - Carbon dioxide flows in a duct at a velocity of 90...Ch. 12 - If nitrogen at 15C is flowing and the stagnation...Ch. 12 - An aircraft cruises at M = 0.65 at 10 km altitude...Ch. 12 - High-speed aircraft use air data computers to...Ch. 12 - A supersonic wind tunnel test section is designed...Ch. 12 - Oxygen flows in a passage at a pressure of 25...Ch. 12 - What is the pressure on the nose of a bullet...Ch. 12 - Prob. 39PCh. 12 - Air flows in an insulated duct. At point the...Ch. 12 - Consider steady, adiabatic flow of air through a...Ch. 12 - Air passes through a normal shock in a supersonic...Ch. 12 - A Boeing 747 cruises at M = 0:87 at an altitude of...Ch. 12 - Space debris impact is a real concern for...Ch. 12 - A CO2 cartridge is used to propel a toy rocket....Ch. 12 - Nitrogen flows from a large tank, through a...Ch. 12 - Air flows from the atmosphere into an evacuated...Ch. 12 - Oxygen discharges from a tank through a convergent...Ch. 12 - The hot gas stream at the turbine inlet of a JT9-D...Ch. 12 - Carbon dioxide discharges from a tank through a...Ch. 12 - Air at 100F and 100 psia in a large tank flows...Ch. 12 - Calculate the required diameter of a convergent...Ch. 12 - Steam flows steadily and isentropically through a...Ch. 12 - Nitrogen flows through a diverging section of duct...Ch. 12 - At a section in a passage, the pressure is 30...Ch. 12 - In a given duct flow M = 2.0; the velocity...Ch. 12 - Air flows isentropically through a converging...Ch. 12 - Five pounds of air per second discharge from a...Ch. 12 - Air flows isentropically through a...Ch. 12 - Air, at an absolute pressure of 60.0 kPa and 27C,...Ch. 12 - Carbon dioxide flows from a tank through a...Ch. 12 - A convergent-divergent nozzle of 50-mm tip...Ch. 12 - Air flows adiabatically through a duct. At the...Ch. 12 - Air flows isentropically through a converging...Ch. 12 - Air flows isentropically through a converging...Ch. 12 - Atmospheric air at 98.5 kPa and 20C is drawn into...Ch. 12 - The exit section of a convergent-divergent nozzle...Ch. 12 - Air flowing isentropically through a converging...Ch. 12 - Air flows from a large tank at p = 650 kPa...Ch. 12 - A converging nozzle is connected to a large tank...Ch. 12 - Air at 0C is contained in a large tank on the...Ch. 12 - A large tank initially is evacuated to 10 kPa...Ch. 12 - Air flows isentropically through a converging...Ch. 12 - Air enters a converging-diverging nozzle at 2 MPa...Ch. 12 - Prob. 75PCh. 12 - A jet transport aircraft, with pressurized cabin,...Ch. 12 - A converging-diverging nozzle, with a throat area...Ch. 12 - Air, at a stagnation pressure of 7.20 MPa absolute...Ch. 12 - A small rocket motor, fueled with hydrogen and...Ch. 12 - Testing of a demolition explosion is to be...Ch. 12 - A total-pressure probe is placed in a supersonic...Ch. 12 - Air flows steadily through a long, insulated...Ch. 12 - Air discharges through a convergent-divergent...Ch. 12 - A normal shock wave exists in an airflow. The...Ch. 12 - Air approaches a normal shock at V1 = 900 m/s, p1...Ch. 12 - Air approaches a normal shock at M1 = 2.5, with...Ch. 12 - Air undergoes a normal shock. Upstream, T1 = 35C,...Ch. 12 - If, through a normal shock wave in air, the...Ch. 12 - The stagnation temperature in an airflow is 149C...Ch. 12 - A supersonic aircraft cruises at M = 2.2 at 12 km...Ch. 12 - The Concorde supersonic transport flew at M = 2.2...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
A picture is taken of a man performing a pole vault, and the minimum radius of curvature of the pole is estimat...
Mechanics of Materials (10th Edition)
The expression for the rate at which useful heat is collected per unit area of the collector and also find the ...
Introduction to Heat Transfer
Comprehension Check 8-10
If the pressure is 250 feet of water [ft H2O], what is the pressure in units of inches...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
In Figure 24.12, the feed is 0.006 in. per tooth. The cutter is rotating at an rpm that will produce the desire...
Degarmo's Materials And Processes In Manufacturing
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- An aircraft flies with a Mach number Ma1=0.962 at an altitude of 7062 m where the pressure is 46.2 kPa and the temperature is 246.2 K. Calculate the stagnation properties (static temperature, pressure, density), cross-section areas A1 and A2=? at the inlet and outlet of the diffuser. The diffuser at the engine inlet has an exit Mach number of Ma2=0.3. For a mass flow rate of 36,2 kg/s, determine the static pressure rise across the diffuser and the exit area. Solve the problem by making the necessary assumptions and drawing the schematic figure.arrow_forwardA converging nozzle is fed with air from a large reservoir where the temperature and pressure are 400 K and 300 kPa, respectively. At a section within the nozzle, where the cross-sectional area is 0.005 m', the velocity is 200 ms·'. The nozzle discharges to the atmosphere with a pressure of 100 kPa. Determine the Mach number; pressure, temperature and crosssectional area at the exit plane. Also find the mass flow rate. The flow Is lsentroplc throughout the nozzlearrow_forwardA large tank supplies helium to a converging-diverging nozzle. The pressure and temperature in the tank remain constant at 6 MPa and 1000 K, respectively. The flow throughout the nozzle is lsentropic. The nozzle discharges to the atmosphere with a pressure of 100 kPa at an exit Mach number of 3. The exit cross-sectional area of the nozzle is 0.001 m'. What is the mass flow rate through the nozzle?arrow_forward
- Q3/ Air at 200 kPa, 100 °C, and Mach number Ma=0.8 flows through a duct. Calculate thevelocity, the stagnation pressure and the stagnation temperature of the air.arrow_forwardn aircraft is flying at an altitude of 12000 metres (T=216.65 K. p = 0.193 bar) at a Mach number of 0.82. The cross sectional area of the inlet diffuser before the L.P. compressor stage is 0.5 m. Determine (a) the mass of air entering the compressor per second (b) the speed of the aircraft (c) the stagnation %3D pressure and temperature of air at the diffuser entry.arrow_forwardAir flows through a long, isentropic nozzle. The temperature and pressure at the * reservoir are 1000K and 20 atm, respectively. If the Mach number at the entrance is 0.2, determine the gas velocity at the entrance. 634 m/s 127 m/s 478 m/s 254 m/s For a large centrifugal pump, the required net positive suction head is typically around 5 ft 2 ft 15 ftarrow_forward
- Consider air entering a heated duct at p1 = 1 atm and T1 = 288 K. Ignore the effect of friction. Calculate the amount of heat per unit mass (in joules per kilogram) necessary to choke the flow at the exit of the duct for an inlet Mach number of M1 = 2.2.arrow_forwardQ.2. Air flows through a constant-area duct is connected to a reservoir at a temperature of 500°C and a pressure of 500 kPa by a converging nozzle, as shown in Figure. Heat is lost at the rate of 250 kJ /kg. Determine the exit pressure and Mach number and the mass flow rate for a back pressure of 0 kPa. q = 250 kJ/kg Pr = 500 kPa Tr = 500°C Po = 0 kPa D= 0.02marrow_forwardAir flows at 200 m/s through the pipe. The temperature is 500 K and the absolute stagnation pressure is 200 kPa. Assume isentropic flow. For air R = 286.9 J/kg · K] and k = 1.40. (Figure 1) 0.3 m Determine the Mach number of the flow. Express your answer using three significant figures. M = Determine the mass flow. Express your answer using three significant figures. m = kg/sarrow_forward
- Air flows from a large tank where the pressure and temperature are 600 kPa and 800 K, respectively, through a converging nozzle with an exit area of 0.0005 m2 and discharges to the atmosphere with a pressure of 100 kPa. The flow Is lsentroplc throughout the nozzle. Determine the Mach number, temperature, pressure and velocity at the exit section, and also calculate the mass flow rate.arrow_forward4- Air at stagnation pressure of 600 kpa and stagnation temperature of 530 K enters a frictionless convergent- divergent nozzle as shown in figure the throat area is 5cm2 and the exit area is 12.5 cm2, the back pressure is 300kpa, and normal shock occurs within the divergent section. Determine the following: A- The Mach number at the exit B- The change in stagnation pressure C- Mx and My are D- The cross sectional area where the shock occurs is approximatelyarrow_forwardIn a wind tunnel air enters with a velocity of 200kmph. The static pressure and temperature of the air at the inlet of the tunnel is 110kPa and 27°C respectively. Determine Mach number, stagnation temperature, stagnation pressure and the stagnation density on a test model installed in the wind tunnel. The size of the tunnel is given as 1m x1m square cross-section. Determine the mass flow rate of the air. For air assume R=287J/kgK ; γ=1.4.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License