Air passes through a normal shock in a supersonic wind tunnel. Upstream conditions are M1 = 1.8, T'1 =270K, and p1 = 10.0 kPa absolute. Downstream conditions are M2 = 0.6165, T2 = 413.6 K. and p2 = 36.13 kPa absolute. (Four significant figures are given to minimize round off errors.) Evaluate local isentropic stagnation conditions (a) upstream from, and (b) downstream from, the normal shock. Calculate the change in specific entropy across the shock. Plot static and stagnation state points on a Ts diagram.
Want to see the full answer?
Check out a sample textbook solutionChapter 12 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Additional Engineering Textbook Solutions
Introduction to Heat Transfer
Degarmo's Materials And Processes In Manufacturing
Engineering Mechanics: Statics
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
DeGarmo's Materials and Processes in Manufacturing
Applied Fluid Mechanics (7th Edition)
- i need the answer quicklyarrow_forwardConsider supersonic airflow approaching the nose of a two-dimensional wedge at a Mach number of 3. Using Fig. , determine the minimum shock angle and the maximum deflection angle a straight oblique shock can have.arrow_forwardFor given air flow with Mach number in test section (i.e. at CD nozzle exit), Me = 8, T01 = 300 K, pressure in test section = 4000 Pa. (1) What is the value of static temperature, stagnation temperature and stagnation pressure in the test section? (2) What is the value of stagnation pressure in the storage thank? (3) What do you conclude about state of air? (4) What is the solution to rectify this problem. i.e. (5)What is the minimum temperature of air should you take in reservoir tank? At this condition, what is mass flow rate in test section? Low pressure air chamber High pressure air storage Storage tank T01 = 300K P01 = ? Settling chamber Pressure regulator Nozzle Screens Test-section Pe = 4000 Pa Me = 8 Te = ? K Sonic throat P0e =? T0e = ? Blow down wind Tunnel (Open circuit type) Diffuser Second throat vacuum tankarrow_forward
- Qs: A two-dimensional supersonic inlet is to be designed to operate at Mach 2.4. Deceleration is to occur through a series of oblique shocks followed by a normal shock, as shown in Figure. Determine the loss of stagnation pressure for the cases of two, three, and four oblique shocks. Assume the wedge turning angles are each 6°. M. = 2.4 Vi, Pai P.- 50 kPa 12° Vi, Pai T.-0° Carrow_forwardAir, with stagnation conditions of 800 kPa and 100°C, ex pands isentropically to a section of a duct where A_{1} = 20 cm² and p_{1} = 47kPa . Compute (a) Ma₁, (b) the throat area, and (c) m. At section 2 between the throat and section 1, the area is 9 cm². (d) Estimate the Mach number at section 2.arrow_forwardConsider a normal shock wave in air. The upstream conditions are given by M = 3, p = 1 atm. and r, = 1.23 kg/m'. Calculate the downstream values of p,, T,, r „ M,, Uz, Po2, and T2: Calculate by using formulas. %3Darrow_forward
- Air flows isentropically through a duct as shown in the figure below. For the conditions shown, find the Mach number at both stations 1 and 2 and the flowrate. The diameter is not necessarily constant. Ma₁ (1) D₁ = 0.15 m V₁ = 40 m/s P1 = 4 atm abs. Ma₁ = Ma₂ = i m₁ = M. kg/s Ma₂ (2 T₂ = 225 K P2 = 2 atm abs.arrow_forwardhe reservoir pressure and temperature for a Laval nozzle are 5 atm [abs] and 520 K,respectively. The flow is isentropically expanded to supersonic speed at the nozzle exitwith area Ae = 4in2. If the exit-to-throat area ratio is 2.295, calculate the followingexit properties: d) ρe; e) p0,e; f) T0,e; gamma = 1.4, R = 287 Please show all work!!arrow_forward(a) A pitot tube indicates a pressure of 265 kPa in an airstream in which the temperature is 10°C and the local Mach number is 1.5. Find the static pressure in the airstream. (b) In another problem, a normal shock wave occurs in air at a point where the stagnation temperature is 300°C and the velocity is 700 m/s. The stagnation pressure is 700 kPa. Under this situation do the following: (i) Draw a diagram and label all flow conditions. (ii) Evaluate the Mach numbers, static and stagnation pressures, static and stagnation temperatures before and after the normal shock. Give reasons to justify your answers.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY