(a) Explanation Given information: At time ( t ) is zero the velocity ( v ) is zero. At time ( t ) is 0.4 sec the position ( x ) is 0.8 ft . Calculation: Show the a-t curve of an accelerometer record for the motion with areas as in Figure (1): Calculate the area ( A 1 ) using the relation: A 1 = 2 3 a ( 16 − 24 ) t 1 Here, a ( 16 − 24 ) is acceleration between 24 ft/s 2 to 16 ft/s 2 and t 1 is time between 0 to 0.2 sec. Substitute 8 ft/s 2 for a ( 16 − 24 ) and 0.2 sec for t 1 . A 1 = 2 3 × 8 × 0.2 = 1.0667 ft/s Calculate the area ( A 2 ) using the relation: A 2 = a ( 0 − 16 ) t 1 Here, a ( 0 − 16 ) is acceleration between 0 ft/s 2 to 16 ft/s 2 . Substitute 16 ft/s 2 for a ( 0 − 16 ) and 0.2 sec for t 1 . A 2 = 16 × 0.2 = 3.2 ft/s Calculate the area ( A 3 ) using the relation: A 3 = ( a ( 0 − 16 ) + a ( 0 − 8 ) 2 ) t 2 Here, a ( 0 − 8 ) is acceleration between 0 ft/s 2 to 8 ft/s 2 and t 2 is time between 0.2 sec to 0.3 sec. Substitute 16 ft/s 2 for a ( 0 − 16 ) , 8 ft/s 2 for a ( 0 − 8 ) and 0 (b) To determine The position of the part at time 0.3 sec ( x 0.3 ) and time 0.2 sec ( x 0.2 ) .

Vector Mechanics for Engineers: Statics and Dynamics

12th Edition

ISBN: 9781259977251

Author: BEER

Publisher: MCG

See similar textbooks

Concept explainers

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be create…

Videos

Question

Chapter 11.3, Problem 11.77P

(a)

To determine

Construct the v-t curve for 0≤t≤0.4sec.

(b)

To determine

The position of the part at time 0.3 sec (x0.3) and time 0.2 sec (x0.2).

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 11.3, Problem 11.76P

Chapter 11.3, Problem 11.78P

Students have asked these similar questions

Correct answer and complete detailed fbd only. I will upvote. : The two steel shafts, each with one end builtinto a rigid support, have flanges attached to their freeends. The flanges are to be bolted together. However,initially there is a 6⁰ mismatch in the location of the boltholes as shown in the figure. Determine the maximumshear stress(ksi) in each shaft after the flanges have beenbolted together. The shear modulus of elasticity for steelis 12 x 106 psi. Neglect deformations of the bolts and theflanges.

Correct detailed answer and complete fbd only. I will upvote. The compound shaft, composed of steel,aluminum, and bronze segments, carries the two torquesshown in the figure. If TC = 250 lb-ft, determine the maximumshear stress developed in each material (in ksi). The moduliof rigidity for steel, aluminum, and bronze are 12 x 106 psi, 4x 106 psi, and 6 x 106 psi, respectively

Correct answer and complete fbd only. I will upvote. A flanged bolt coupling consists of two concentric rows of bolts. The inner row has 6 nos. of 16mm diameterbolts spaced evenly in a circle of 250mm in diameter. The outer row of has 10 nos. of 25 mm diameter bolts spaced evenly in a circle of 500mm in diameter. If the allowable shear stress on one bolt is 60 MPa, determine the torque capacity of the coupling. The Poisson’s ratio of the inner row of bolts is 0.2 while that of the outer row is 0.25 and the bolts are steel, E =200 GPa.

Chapter 11 Solutions

Vector Mechanics for Engineers: Statics and Dynamics

Ch. 11.1 - A bus travels the 100 miles between A and B at 50...Ch. 11.1 - Two cars A and B race each other down a straight...Ch. 11.1 - A snowboarder starts from rest at the top of a...Ch. 11.1 - The motion of a particle is defined by the...Ch. 11.1 - The vertical motion of mass A is defined by the...Ch. 11.1 - A loaded railroad car is rolling at a constant...Ch. 11.1 - A group of hikers uses a GPS while doing a 40-mile...Ch. 11.1 - The motion of a particle is defined by the...Ch. 11.1 - A girl operates a radio-controlled model car in a...Ch. 11.1 - The motion of a particle is defined by the...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Construct the v-t curve for 0 ≤ t ≤ 0.4 sec .

Solution Summary: The author shows the a-t curve of an accelerometer record for the motion with areas as in Figure 1.