Explanation Show the T-s diagram for ideal gas refrigeration system as in Figure (1). Express temperature at state 2 s . T 2 s = T 1 [ P 2 P 1 ] ( k − 1 ) / k (I) Here, temperature at state 1 is T 1 , pressure at state 1 and 2 is P 1 and P 2 respectively, and heat capacity ratio is k . Express temperature at state 4 s . T 4 s = T 3 [ P 4 P 3 ] ( k − 1 ) / k (II) Here, temperature at state 3 is T 3 , pressure at state 3 and 4 is P 3 and P 4 respectively. Express temperature at state 6 s . T 6 s = T 5 [ P 6 P 5 ] ( k − 1 ) / k (III) Here, temperature at state 5 is T 5 , pressure at state 5 and 6 is P 5 and P 6 respectively. Express temperature at state 2. T 2 = T 1 + ( T 2 s − T 1 ) η C (IV) Here, isentropic efficiency of compressor is η C . Express temperature at state 4. T 4 = T 3 + ( T 4 s − T 3 ) η C (V) Express temperature at state 6. T 6 = T 5 − η T ( T 5 − T 6 s ) (VI) Here, isentropic efficiency of turbine is η T . Express the coefficient of performance of the ideal gas refrigeration cycle. COP R = q L w comp,in − w turb,out = h 1 − h 6 ( h 2 − h 1 ) + ( h 4 − h 3 ) − ( h 5 − h 6 ) = T 1 − T 6 ( T 2 − T 1 ) + ( T 4 − T 3 ) − ( T 5 − T 6 ) (VII) Here, heat lost is q L , power input to compressor is w comp,in , power rejected out from turbine is w turb,out , specific enthalpy at state 1, 2, 3 4, 5 and 6 is h 1 , h 2 , h 3 , h 4 , h 5 and h 6 respectively, temperature at state 1,2 ,3, 4, 5 and 6 is T 1 , T 2 , T 3 , T 4 , T 5 and T 6 respectively. Express the mass flow rate of the air. m ˙ = Q ˙ refrig c p ( T 1 − T 6 ) (VIII) Here, rate of refrigeration rate is Q ˙ refrig and specific heat at constant pressure of air is c p . Conclusion: Perform unit conversion of temperature at state 1 3, and 5 from ° C to K . T 1 = − 24 °C = ( − 24 + 273 ) K = 249 K T 3 = 5 °C = ( 5 + 273 ) K = 278 K T 5 = 5 °C = ( 5 + 273 ) K = 278 K Refer Table A-2, “ideal gas specific heats of various common gas”, and write the properties of air. c p = 1.005 kJ / kg ⋅ K k = 1.4 Substitute 249 K for T 1 , 3 for P 2 / P 1 and 1.4 for k in Equation (I). T 2 s = ( 249 K ) ( 3 ) ( 1.4 − 1 ) / 1

9th Edition

ISBN: 9781260048766

Author: CENGEL

Publisher: MCG

See similar textbooks

Concept explainers

IC engines

The term "engine" indicates a mechanical device/machine used to convert input energy to a specific mechanical output. The input energy may be in the form of chemical energy, thermal energy, or so on and mechanical output is in the form of mechanical ener…

Question

Chapter 11.10, Problem 81P

To determine

The coefficient of performance of the system and the rate at which air must be circulated through the system.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 11.10, Problem 80P

Chapter 11.10, Problem 82P

Students have asked these similar questions

8 mm- Top view -200 mm-180 mm- D B B 12 mm Side view B -8 mm D PROBLEM 1.56 In an alternative design for the structure of Prob. 1.55, a pin of 10-mm-diameter is to be used at A. Assuming that all other specifications remain unchanged, determine the allowable load P if an overall factor of safety of 3.0 is desired. PROBLEM 1.55 In the structure shown, an 8- mm-diameter pin is used at A, and 12-mm- diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 3.0 is desired. 20 mm P 8 mm- 12 mm- Front view

Where on the beam below is the Maximum Deflection likely to occur? 2P A "ती Point A Point B Point C Point D Point B or Point D ८ B प

Sign in ||! PDE 321 proje X IMB321 PDF Lecture 5 X PDF Planet Ec X PDF Planet Ec X PDF PEABWX PDF meeting x PDF GSS Quo X PDF File C:/Users/KHULEKANI/Downloads/CIVE%20281%20Ass-2.pdf Draw | | All | a | Ask Copilot + 1 of 7 | D SOLUTION B PROBLEM 12.16 Block 4 has a mass of 40 kg, and block B has a mass of 8 kg. The coefficients of friction between all surfaces of contact are μ, = 0.20 H = 0.15. Knowing that P = 50 N→, determine (a) the acceleration of block B, (b) the tension in the cord. Constraint of cable: 2x + (x-x1) = x + x = constant. a+ag = 0, or aB = -a Assume that block A moves down and block B moves up. Block B: +/ΣF, = 0: NAB - WB cos 0 = 0 =ma: -T+μN + Wsin = We as g + ΣΕ We Eliminate NAB and aB- NAB B Nas HN UNA A NA -T+W(sin+μcоsе) = WB- g VD"M- g Block A: +/ΣF, = 0: NA-NAB - W₁cos + Psinė = 0 N₁ = N AB+W cose - Psin = (WB+WA)cose - Psinė ΣF=ma -T+Wsino-FAB-F + Pcos = CIVE 281 X + Ждал g Q | го || حالم ☑

Chapter 11 Solutions

Thermodynamics: An Engineering Approach

Ch. 11.10 - Why do we study the reversed Carnot cycle even...Ch. 11.10 - Why is the reversed Carnot cycle executed within...Ch. 11.10 - A steady-flow Carnot refrigeration cycle uses...Ch. 11.10 - Refrigerant-134a enters the condenser of a...Ch. 11.10 - Does the ideal vapor-compression refrigeration...Ch. 11.10 - Why is the throttling valve not replaced by an...Ch. 11.10 - In a refrigeration system, would you recommend...Ch. 11.10 - Does the area enclosed by the cycle on a T-s...Ch. 11.10 - Consider two vapor-compression refrigeration...Ch. 11.10 - It is proposed to use water instead of...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The coefficient of performance of the system and the rate at which air must be circulated through the system.

Solution Summary: The author shows the T-s diagram for ideal gas refrigeration system as in Figure (1).

Concept explainers

The coefficient of performance of the system and the rate at which air must be circulated through the system.

Want to see the full answer?

Chapter 11 Solutions