Math instruction: Math instructions refer to all output instructions that uses the data of two words or registers and perform the desired function. Math instructions are program based on the type of processor used. The data manipulation instructions are almost similar to math instructions. The math instruction allows the PLC to take more of conventional computer qualities. Math instructions are normally used to perform arithmetic functions on the values stored in memory words or registers. Math functions: The basic math functions performed by PLCs are as follows: Addition This function is used to add one piece of data to another. It is also called as ADD. Subtraction This function is used to subtract one piece of data from another. It is also called as SUB. Multiplication This function is used to multiply one piece of data by another. It is also called as MUL. Division This function is used to divide one piece of data from another. It is also called as DIV. Terms used: The following terms are used in the instruction. Source A Source A refers to the address of the first piece of data that is used in the instruction. Source B: Source B refers to the address of the second piece of data that is used in the instruction. Destination Destination refers to the address where the results of the instruction are stored.

Question

Want to see the full answer?

Answer 1

Question

Chapter 11, Problem 8RQ

Program Plan Intro

Math instruction:

Math instructions refer to all output instructions that uses the data of two words or registers and perform the desired function.

Math instructions are program based on the type of processor used.

The data manipulation instructions are almost similar to math instructions.

The math instruction allows the PLC to take more of conventional computer qualities.

Math instructions are normally used to perform arithmetic functions on the values stored in memory words or registers.

Math functions:

The basic math functions performed by PLCs are as follows:

Addition

This function is used to add one piece of data to another.

It is also called as ADD.

Subtraction

This function is used to subtract one piece of data from another.

It is also called as SUB.

Multiplication

This function is used to multiply one piece of data by another.

It is also called as MUL.

Division

This function is used to divide one piece of data from another.

It is also called as DIV.

Terms used:

The following terms are used in the instruction.

Source A

Source A refers to the address of the first piece of data that is used in the instruction.

Source B:

Source B refers to the address of the second piece of data that is used in the instruction.

Destination

Destination refers to the address where the results of the instruction are stored.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

After playing our giving implementation, your task is to implement Dinning Philosophers with semaphore in C, by including and Your implementation will require creating five philosophers, each identified by a number 0.4. Each philosopher will run as a separate thread. Create threads using Pthreads as discussed in the Lecture slides on Chapter 4 and Practice Lab on Threads. Your solution needs to accomplish the following: Implement in C (15 points) 1. dp1.c - You are to provide your solution to this assignment as a single C program named 'dp1.c using semaphore. Explain in you code (as comments) that the dead lock will happen or not. If there is a possible deadlock, you can simply solve the deadlock by pick the fork in order like the first solution in our slides. Solve Deadlock by Footman (15 points) 1. Here is a new solution to overcome the deadlock. The Dining Philosophers decide to hire a footman whose task to allow only four philosophers to sit on the table. When entering and…

8.4 Self-Bias Configuration 20. Determine Zi. Zo. and A,, for the network of Fig. 8.73 if gf, = 3000 μS and gos = 50 μs. 21. Determine Z, Zo, and A, for the network of Fig. 8.73 if the 20-uF capacitor is removed and the parameters of the network are the same as in Problem 20. Compare results with those of Problem 20. +12 V 3.3 ΚΩ HE C₂ Vo Z Zo C₁ 10 ΜΩ Z₁ 1.1 ΚΩ Cs 20 µF FIG. 8.73 Problems 20, 21, 22, and 59.

21. Determine Zi, Zo, and A, for the network of Fig. 8.73 if the 20-μF capacitor is removed and the parameters of the network are the same as in Problem 20. Compare results with those of Problem 20. +12 V 3.3 ΚΩ +6 C₂ C₁ Z₁ 10 ΜΩ 1.1 ΚΩ Cs 20 μF FIG. 8.73 Zo