Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 11, Problem 36P
Water flows uniformly at a depth of 1.2 m in a rectangular canal 3 m wide laid on a slope of 1 m per 1000 m. What is the mean shear stress on the sides and bottom of the canal?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
An irrigation channel of trapezoidal section, having side slopes 3
horizontal to 2 vertical, is to carry flow of 10 cumec on a longitudinal
slope of 1 in 5000. The channel is to be lined for which the value of
friction coefficient in Manning's formula is n = 0.012. Find the dimensions
of the most economic section of the channel.
Consider the uniform flow of water in the triangular channel shown in the figure. The
channel bed slope is 0.003 and the roughness coefficient is 0.025. The flow rate in the
channel is 25 m³/s.
What is the normal depth?
a.3.48 m
b.2.28 m
c.4.70 m
d. 1.98 m
What is the critical depth?
a. 1.98 m
b.4.70 m
c.3.48 m
d.2.28 m
If the flow depth at a certain section of the channel is 2 m, the flow is:
a.subcritical
b.critical
c.supercritical
d.can not be determined
VAI
2
1
Q(1): A power canal of trapezoidal section has to be excavated through hard clay at least
cost. Determine the dimensions of the channel, given, discharge equal to 14 m3/s, bed
slope 1:2500 and Manning's n = 0.02.
Chapter 11 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 11 - Verify the equation given in Table 11.1 for the...Ch. 11 - A pebble is dropped into a stream of water that...Ch. 11 - Solution of the complete differential equations...Ch. 11 - A water flow rate of 250 cfs flows at a depth of 5...Ch. 11 - Determine and plot the relation between water...Ch. 11 - Capillary waves (ripples) are small amplitude and...Ch. 11 - The Froude number characterizes flow with a free...Ch. 11 - Consider waves on the surface of a tank of water...Ch. 11 - A submerged body traveling horizontally beneath a...Ch. 11 - Water flows in a rectangular channel at a depth of...
Ch. 11 - A partially open sluice gate in a 5-m-wide...Ch. 11 - Find the critical depth for flow at 3 m3/s in a...Ch. 11 - Flow occurs in a rectangular channel of 6 m width...Ch. 11 - What is the maximum flow rate that may occur in a...Ch. 11 - A rectangular channel carries a discharge of 10...Ch. 11 - Flow in the channel of Problem 11.15 has a...Ch. 11 - Consider the Venturi flume shown. The bed is...Ch. 11 - Eleven cubic meters per second of water are...Ch. 11 - A rectangular channel 10 ft wide carries 100 cfs...Ch. 11 - At what depths can 800 cfs flow in a trapezoidal...Ch. 11 - At a section of a 10-ft-wide rectangular channel,...Ch. 11 - Water, at 3 ft/s and 2 ft depth, approaches a...Ch. 11 - A horizontal rectangular channel 3 ft wide...Ch. 11 - A hydraulic jump occurs in a rectangular channel...Ch. 11 - A hydraulic jump occurs in a wide horizontal...Ch. 11 - A hydraulic jump occurs in a rectangular channel....Ch. 11 - The depths of water upstream and downstream from a...Ch. 11 - Calculate y2, h, and y3 for this two-dimensional...Ch. 11 - The hydraulic jump may be used as a crude flow...Ch. 11 - A hydraulic jump occurs on a horizontal apron...Ch. 11 - A hydraulic jump occurs in a rectangular channel....Ch. 11 - A positive surge wave, or moving hydraulic jump,...Ch. 11 - A 2-m-wide rectangular channel with a bed slope of...Ch. 11 - Determine the uniform flow depth in a rectangular...Ch. 11 - Determine the uniform flow depth in a trapezoidal...Ch. 11 - Water flows uniformly at a depth of 1.2 m in a...Ch. 11 - This large uniform open channel flow is to be...Ch. 11 - A rectangular flume built of timber is 3 ft wide....Ch. 11 - A channel with square cross section is to carry 20...Ch. 11 - A triangular channel with side angles of 45 is to...Ch. 11 - A flume of timber has as its cross section an...Ch. 11 - At what depth will 4.25 m3/s flow uniformly in a...Ch. 11 - A semicircular trough of corrugated steel, with...Ch. 11 - A rectangular flume built of concrete with 1 ft...Ch. 11 - Water flows in a trapezoidal channel at a flow...Ch. 11 - What slope is necessary to carry 11 m3/s uniformly...Ch. 11 - Find the normal depth for the channel of Problem...Ch. 11 - For a trapezoidal shaped channel with n = 0.014...Ch. 11 - Compute the critical depth for the channel in...Ch. 11 - A trapezoidal canal lined with brick has side...Ch. 11 - An optimum rectangular storm sewer channel made of...Ch. 11 - For a sharp-crested suppressed weir of length B =...Ch. 11 - A rectangular sharp-crested weir with end...Ch. 11 - What is the depth of water behind a rectangular...Ch. 11 - A broad-crested weir 0.9 m high has a flat crest...Ch. 11 - The head on a 90 V-notch weir is 1.5 ft. Determine...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
9.19 An aluminum rod 25mm in diameter and 4m long is subjected to an axial tensile load of 65 kN. Compute
(a) s...
Applied Statics and Strength of Materials (6th Edition)
A horizontal force of F = {50i} N is applied perpendicular to the handle of the pipe wrench. Determine the mome...
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Water at a flow rate of m =0.215kg/s is cooled from 70°C to 30°C by passing it through a thin-walled tube of di...
Fundamentals of Heat and Mass Transfer
The bars of the truss each have a cross-sectional area of 1.25 in2. Determine the average normal stress in memb...
Mechanics of Materials (10th Edition)
Replace the force system acting on the beam by an equivalent force and couple moment at point B.
Engineering Mechanics: Statics
Peg P is driven by the forked link OA along the described by r=e, where r is in meters =4 rad, the link has an ...
Engineering Mechanics: Dynamics (14th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- An irrigation channel is to carry a discharge of 14 cumec with a velocity of 0.9 m/s and bed slope of 1 in 2500. The side slopes are 1 to 1. Find the depth and bottom width. The values of Chezy" C for this channel for different values of hydraulic radius R are as tabulated below. Hydraulic radius R 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 Chezy's C 34 35 37 38 39 40 41 41arrow_forwardQuestion : A stream bed has a rectangular cross section 5 meters wide and a slope of 0.0002 m/m. The flow rate in the stream is 8.75 m³/s. A dam is built across the stream, causing the water surface to rise to 2.5 meters just upstream of the dam, as shown below. Assume n = 0.015. y = yn 2.5 m a. Find the normal depth, yn, corresponding to this flow rate and channel geometry. You do not need to solve the equation by hand. To get full credit, show your equation with only one unknown. b. Find the critical depth, yc. c. The yn is found to be 1.8 m by solving the equation numerically. Identify the water surface profile upstream of the dam. Explain your answer for full credit.arrow_forwardi need the answer quicklyarrow_forward
- At what depth will water flow in a 4 m wide rectangular channel if n=0.018, S0=0.0009, and Q=7m^3/s?arrow_forwardQUESTION 2 At a certain location in Durban, under normal conditions the water flows uniformly in a finished-concrete rectangular channel. During the recent floods' conditions, the overflow regions consisting of light brush was observed to increase the flow rate by 45%. Estimate the depth D if the bottom slope of the channel is 0.1°. D 1.5 m -5 m -5 m 2 m Figure 1arrow_forwardNiloarrow_forward
- v² L 1) Show that the expression for head loss in a half full pipe is stilh, = f 2g D Why is it the same as for a full pipe? Prove to yourself that the bed shear stress in a rectangular channel is to=pgRhSo (see slide 157). What is the expression for a wide rectangular channel? 2) Find the necessary fall in elevation of the channel below if it required to carry a uniform flow of 25m/s over a distance of 10km. Assume a bed roughness of 3mm and use a Darcy friction factor. 1.5m 1.5m 4m 1.5m (Ans: (f-0.018), (C=66m²/s), 14.4m)arrow_forwardA channel step, shown in the figure below, is in a 12 m wide channel with discharge, Q, of 46 m3/s. The flow depth at section 1 is 1.6 m and the step height is 0.4 m. The bed of the channel, upstream and downstream of the step, is horizontal and smooth. Part A. Sketch on the figure the variation of the pressure with depth at sections 1 and 2, and on the verticalface of the step. Sections 1 and 2 are located far enough from the step for the velocity to be essentially horizontal and uniform. Part B. Draw the control volume contained between sections 1 and 2 and show on the figure the forces acting on it. Show also your choice for the positive direction of distance and of force. Part C. Write the momentum equation as applied to the control volume between sections 1 and 2, using the sign convention you have chosen. Show the forces and velocities used in the momentum equation. Part D. Compute the following quantities: (a) Velocity of flow at section 1. (b) Specific energy at section 1. (c)…arrow_forwardWater flows in an open channel across a weir which occupies the full width of the channel. The lenght of the weir is 0.5 m and the height of water over the weir is 100 mm. What is the flow rate of water?arrow_forward
- EXERCISE 3: Water flows at a rate of q=3.13 m/s.m in a rectangular channel shown in the figure on the right. Ja0.00023 no0.015 • Determine the uniform flow depths and the types of flow in Ja 0.00762 Pe-0.015 different parts of the channel. Draw the water surface profile in the transition zone,arrow_forwardWater flows uniformly in a rectangular channel with finished-concrete surfaces. The channel width is 3 m, the flow depth is 1.2 m, and the bottom slope is 0.002. Determine if the channel should be classified as mild, critical, or steep for this flow.arrow_forward2) A venturi flume is placed near the middle of a long rectangular channel with Manning's coefficient n= 0.012 m s. The channel has a width of 5 m, a discharge of 12.5 m's" and a slope of 1:2500. (a) Determine the critical depth and the normal depth in the main channel. (b) Determine the venturi flume width which will just make the flow critical at the contraction. (c) If the contraction width is 2 m find the depths just upstream, downstream and at the throat of the venturi flume (neglecting friction in this short section). (d) Sketch the surface profile.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Physics 33 - Fluid Statics (1 of 10) Pressure in a Fluid; Author: Michel van Biezen;https://www.youtube.com/watch?v=mzjlAla3H1Q;License: Standard YouTube License, CC-BY