Materials for Civil and Construction Engineers (4th Edition)
4th Edition
ISBN: 9780134320533
Author: Michael S. Mamlouk, John P. Zaniewski
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 11, Problem 11.26QP
(a)
To determine
The modulus of elasticity of the reinforced concrete.
(b)
To determine
The load carried by the each of the steel and plain concrete.
(c)
To determine
The minimum required cross sectional area of the column.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A short reinforced concrete column is subjected to a 1000 kN axial compressive load. The moduli of elasticity of plain concrete and steel are 25 and207 GPa, respectively, and the cross-sectional area of steel is 2% of that of thereinforced concrete. Considering the column as a structural member made of a composite material and subjected to load parallel to the steel rebars, calculate the following:a. the modulus of elasticity of the reinforced concreteb. the load carried by each of the steel and plain concretec. the minimum required cross-sectional area of the column given that the allowable compressive stress of plain concrete is 20 MPa and that the allowable compressive stress of plain concrete will be reached before that of steel.
A representative reinforced concrete composite beam section is shown in the figure below. The number of reinforcement is 6 and the diameter of the reinforcement is 16 meters. cross section Determine the neutral axis (x) and calculate the maximum normal stresses that will occur in concrete and steel. It will be assumed that the concrete does not carry tensile stress. The modulus of elasticity of the steel is 200000 Mpa. The modulus of elasticity of concrete is 28000 Mpa. The section width is b= 400 mm. Take the cover as 50 mm.
(The maximum bending moment acting on the section is 59 kNm and d= 700 mm.)
For the cross section shown below, the material and sectional properties are given as follows:
Determine the modular ratio. The concrete modulus of elasticity can be estimated by [psi] where must be in unit psi.
(b) Draw the transformed section.
(C) Show that the cross-section is elastic and does not have cracks when a bending moment of 1,000 kips-in is applied.
Also, given the bending moment, find the maximum stress in concrete and steel.
The neutral axis is at 11.05 in. from the top surface, and the moment of inertia around the neutral axis is 26676 in4.
Chapter 11 Solutions
Materials for Civil and Construction Engineers (4th Edition)
Ch. 11 - Prob. 11.1QPCh. 11 - Prob. 11.2QPCh. 11 - Prob. 11.3QPCh. 11 - Prob. 11.4QPCh. 11 - Prob. 11.5QPCh. 11 - Prob. 11.6QPCh. 11 - Prob. 11.7QPCh. 11 - Prob. 11.8QPCh. 11 - Prob. 11.9QPCh. 11 - What are the functions of aggregate used in...
Ch. 11 - Prob. 11.11QPCh. 11 - Prob. 11.12QPCh. 11 - What are the benefits of adding dispersed steel...Ch. 11 - Getting measurements from Figure 11.20, determine...Ch. 11 - Three 6 in. 12 in. concrete cylinders with...Ch. 11 - Prob. 11.16QPCh. 11 - Prob. 11.17QPCh. 11 - Prob. 11.18QPCh. 11 - Prob. 11.19QPCh. 11 - Prob. 11.20QPCh. 11 - Prob. 11.21QPCh. 11 - Prob. 11.22QPCh. 11 - Prob. 11.23QPCh. 11 - Prob. 11.24QPCh. 11 - Prob. 11.25QPCh. 11 - Prob. 11.26QPCh. 11 - Prob. 11.27QPCh. 11 - Prob. 11.28QPCh. 11 - Prob. 11.29QPCh. 11 - Prob. 11.30QPCh. 11 - A circular FRP composite rod with continuous and...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A short reinforced concrete column is subjected to a 1000 kN axial compressive load. Themoduli of elasticity of plain concrete and steel are 25 GPa and 207 GPa, respectively, and thecross-sectional area of steel is 2% of that of the reinforced concrete. Considering the columnas a structural member made of a composite material and subjected to load parallel to the steelrebars, calculate the following:a) The modulus of elasticity of the reinforced concreteb) The load carried by each of the steel and plain concretec) The minimum required cross-sectional area of the column given that the allowablecompressive stress of plain concrete is 20 MPa and that the allowable compressivestress of plain concrete will be reached before that of steelarrow_forwardThe cross-section of the reinforced concrete beam having an effective depth of 500 mm is shown in the figure (not drawn to the scale). The grades of concrete and steel used are M35 and Fe550, respectively. The area of tension reinforcement is 400 mm?. It is given that the corresponding to 0.2% proof stress, the material safety factor is 1.15 and the yield strain of Fe550 steel is 0.0044. 500 mm 100 mm 200 mm 0 A, = 400 mm? As per IS 456:2000, the limiting depth (in mm, round off to nearest integer) of the neutral axis measured from the extreme compression fiber, is ww 00arrow_forwardDetermine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 28 MPa and steel yield strength fy = 420 MPa. 1. if the tensile strain is εs = fy/Es upon crushing of concrete at a strain of 0.003. = (5 decimal places) 2. if the tensile strain is set as 0.010 upon crushing of concrete at a strain of 0.003. = (5 decimal places) 3. Minimum as required by NSCP 2015. = (5 decimal places)arrow_forward
- The composite bar in the figure is stress-free before the axial loads P₁ and P2 are applied. Assuming that the walls are rigid, calculate the stress in each material if P₁= 150 kN and P₂ = 90 kN. Aluminum Steel Bronze A = 900 mm² A = 2000 mm² A = 1200 mm² E = 70 GPa E = 200 GPa E = 83 GPa P₁ 500 mm P₂ 250 mm 350 mm (a) Determine the stress in the aluminum. (b) Determine the stress in the steel. (c) Determine the stress in the bronze.arrow_forward14. The composite bar in the figure is stress-free before the axial loads PI and P2 are applied. Assuming that the left wall is rigid, while the right wall yields 0.80mm. calculate the stress in each material if PI = 150 kN and P2 = 90 kN. Aluminum Steel 150 kN 500 mm Bronze 1 90 KN 250 mm 350 mm 0.8 mmarrow_forwardA composite beam is constructed using a steel plate (14 mm ✕ 125 mm) with two wood beams (75 mm ✕ 125 mm) on either side. The wood and steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment Mz = 6.80 kN · m. Calculate the maximum tensile and compressive stresses in the wood and steel if Ew = 11 GPa and Es = 200 GPa. (Enter your answers in MPa. Use the deformation sign convention. Use the general theory for composite beams described in the textbook.) maximum tensile stress in wood MPa maximum tensile stress in steel MPa maximum compressive stress in wood MPa maximum compressive stress in steel MPaarrow_forward
- A RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION, 20mm WIDE IN THE Z DIRECTION AND 25mm THICK IN THE X DIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF A UNIFORMLY DISTRIBUTED FORCE OF Px=3 (COMPRESSION), Py=6 (TENSION) AND Pz=9 (COMPRESSION) IN THE X, Y AND Z DIRECTIONS RESPECTIVELY. IF THE POISSON’S RATIO = 1/4 & E = 70 GPa, DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSO DETRMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THE WOULD PRODUCE THE SAME X DEFORMATION AS THE ORIGINAL.arrow_forwardThe cross-section of the reinforced concrete beam having an effective depth of 500 mm is shown in the figure (not drawn to the scale). The grades of concrete and steel used are M35 and Fe550. respectively The area of tension reinforcement is 400 mm. It is given that the corresponding to 0.2% proof stress, the material safety factor is 1.15 and the yield strain of Fe550 steel i5 0.0044. 500 mm 100 mm 200 mm A = 400 mm As per IS 456:2000, the limiting depth (in mm, round off to nearest integer) of the neutral axis measured from the extreme compression fiber, isarrow_forwardThe composite material is fastened to their junction at rigid plate B and attached to rigid fixed supports at both ends subjected to two loads of 12k positioned symmetrically at B. Determine the stresses and their corresponding behavior for each material. Use 2 decimal places in every solved value. 亚 А 12k 12k 1 ft Steel Est = 29 x 10° psi Ast = 1.03 in? B Aluminum 2 ft Eal = 10 × 106 psi Aal = 8.92 in² Carrow_forward
- Please answer, Asap. Thank you.arrow_forwardThe composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. The cross-sectional areas of sections AB, BC, and CD are AAB = 0.08 in², ABC = 0.11 in², and Acp = 0.06 in², respectively. The modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C.arrow_forwardDetermine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa. 16. if the tensile strain is εs = fy/Es upon crushing of concrete at a strain of 0.003. = [r] (5 decimal places)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill Education
Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Structural Analysis (10th Edition)
Civil Engineering
ISBN:9780134610672
Author:Russell C. Hibbeler
Publisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Structural Analysis
Civil Engineering
ISBN:9780073398006
Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
Publisher:McGraw-Hill Education
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning