
(a)
Interpretation:
Whether the alloy is hypoeutectic or hypereutectic needs to be determined.
Concept Introduction:
The composition of an alloy that lies to the left of the eutectic point in the alloy phase diagram is termed as a hypo-eutectic alloy. Whereas the composition of an alloy that lies to the right of the eutectic point in the alloy phase diagram is termed as a hyper-eutectic alloy. The hypereutectic alloy has a composition beyond the eutectic point.
(b)
Interpretation:
The value of composition of the first solid formed during the solidification needs to be determined.
Concept Introduction:
Freezing is the other name for solidification. Solidification is the phase change of matter which results in the production of a solid phase. Mostly, this phase occurs when the temperature of a liquid is lowered under the freezing point. At the solidification temperature, atoms which are present in the liquid begins to bond and start the formation of crystals.
(c)
Interpretation:
The composition and amount of each phase at 184°C needs to be determined.
Concept Introduction:
Solidification process is also known as a Freezing process which is a phase change of matter. The phase change of matter that results in the production of the solid phase. Regularly, this occurs when the temperature of the liquid is lowered below the freezing point. Undercooling of liquids takes place in the process of solidification. Solidification can yield metastable product structures at high undercooling. The constituents of the metastable products are the result of kinetic competition.
(d)
Interpretation:
The composition and amount of each phase at 182°C needs to be determined.
Concept Introduction:
Solidification process is also known as a freezing process which is a phase change of matter. The phase change of matter that results in the production of the solid phase. Regularly, this occurs when the temperature of the liquid is lowered below the freezing point. Undercooling of liquids takes place in the process of solidification. Solidification can yield metastable product structures at high undercooling. The constituents of the metastable products are the result of kinetic competition.
(e)
Interpretation:
The composition and amount of each microconstituent at 182°C needs to be determined.
Concept Introduction:
Solidification process is also known as a Freezing process which is a phase change of matter. The phase change of matter that results in the production of the solid phase. Regularly, this occurs when the temperature of the liquid is lowered below the freezing point. Undercooling of liquids takes place in the process of solidification. Solidification can yield metastable product structures at high undercooling. The constituents of the metastable products are the result of kinetic competition.
(f)
Interpretation:
The composition and amount of each phase at 25°C needs to be determined.
Concept Introduction:
Solidification process is also known as a Freezing process which is a phase change of matter. The phase change of matter that results in the production of the solid phase. Regularly, this occurs when the temperature of the liquid is lowered below the freezing point. Undercooling of liquids takes place in the process of solidification. Solidification can yield metastable product structures at high undercooling. The constituents of the metastable products are the result of kinetic competition.

Trending nowThis is a popular solution!

Chapter 11 Solutions
Essentials Of Materials Science And Engineering
- 20-4-2025 Exam-2-Tribology Q1: What are the assumptions of hydrodynamic lubrication theory: Q2: Explain with sketch the cycle or process of engine lubrication system-pressurized lubrication system Q3: A short bearing is designed to operate with an eccentricity ratio = 0. 7. The journal diameter is 60 mm, and its speed is 1300 r.p.m. The journal is supported by a short hydrodynamic bearing of length L/D = 0. 5, and clearance ratio C/R = 103. The radial load on the bearing is 9800 N. a. Find the Sommerfeld number. b. Find the minimum viscosity of the lubricant for operating at ε = 0.7 c. Select a lubricant if the average bearing operating temperature is 70°c Q4: Two parallel circular disks of 100 mm diameter have a clearance of Imm between them. Under load, the downward velocity of the upper disk is 2 m/s. At the same time, the lower disk is stationary. The clearance is full of SAE 40 oil at a temperature of 60°c. a. Find the load on the upper disk that results in the instantaneous…arrow_forwardTribobolgy 15/2022 Monthly Exam. Automobile Eng. Dert 2nd Semster/3rd class Max. Mark: 100% 7. Viscosity of multi-grade oils (a) Reduces with temperature (c) is less sensitive to temperature (b) Increases with temperature (d) None of the above 8. In a hydrodynamic journal bearing if eccentricity ratio = 1, it means (a) Journal/shaft is subjected to no load and the rotational speed is very high. (b) Journal is subjected to no load and the rotational speed is moderate (c) Journal is subjected to very light load and the rotational speed is very high. (d) Journal is subjected to very high load and the rotational speed is negligible. Q4/ The journal speed of a 100mm diameter journal is 2500 rpm. The journal is supported by a short hydrodynamic bearing of length L=0.6D, eccentricity ratio = 0.75 and a clearance ratio C/R=0.001. The radial load on the bearing is 10 kN. The lubricant is SAE 30, and the operating temperature of the lubricant in the bearing is 700C. 1- Assume…arrow_forward8. Determine the center frequency and Bandwidth of the following bandpass filter, show all steps.arrow_forward
- 5. Find the Transfer Function of the following circuit. Prove that it’s a low pass filter, show all steps.arrow_forward2. Find the transfer function, show all steps.arrow_forward1 of 2 Monthly Exam. Automobile Eng. Dert 2nd Semster/3rd class Max. Mark: 100% Q1/A/ Compare between the long and short journal bearings B/ With the help of Stribeck's curve, discuss different regimes of lubrication. C/ Explain the importance of Tribology in the design of different machine elements Q2 /A/ According to the SAE viscosity grading system all engine oils are divided into two classes: monograde and multi-grade. Compare between them? B/What are the differences between grease and Synthetic oils C/ Explain the effect of eccentricity ratio & with respect to hydrodynamic journal bearing. Q3/A/ What are the major factors which affect the selection of lubricants? B/What are the criteria to classify sliding bearings? C/ Answer of the following: 1. According to the SAE viscosity classification, the oil (SAE 40) is lower viscosity than the oil (SAE 20) at the same temperature. (True or False) 2. For a slow speed-highly loaded bearing, used oils of high viscosity; while for high-speed…arrow_forward
- Using a relevant image such as a 3D architectural rendering of a warehouse landscape in Edmond.arrow_forwardA simple beam has a span of 10 m and supports a total uniformly distributed load of 12 kN/m. Properties of W 480×86: Property Value A = 10800 mm² bf = 180 mm tf = 15 mm Ix = 383.13 × 10⁶ mm⁴ tw = 12 mm d = 480 mm Questions: Calculate the maximum shear in the beam in kN. Calculate the average shear stress in the beam in MPa. Calculate the maximum shear stress in the beam in MPa. Given the properties of the wide flange: Property Value d = 530 mm bf = 210 mm tw = 18 mm tf = 16 mm Question: Compute the value of rₜ, defined as the radius of gyration of the compression flange plus 1/3 of the compression web area about the y-axis.arrow_forwardGiven an existing two-story steel structure with interior columns spaced as shown in Fig.2. The columns are spaced at 18 ft in the North-South direction and at 30 ft in the East-West direction. An interior lower-story column is to be removed by adding newsteel girder as shown in Fig. 4. The floor dead loads and the roof dead loads are 70 psfand 18 psf respectively. The floor live loads and the roof live loads are 50 psf and20 psf respectively. All existing steel materials are ASTM A36 steel (Fy=36 ksi). Newgirder is ASTM A992 steel (Fy= 50 ksi). All columns are W8x31. Use the LRFD Method.Assumptions:1- The loads given include column and beam self weights.2- Existing beam and new girder are simply supported at both ends.3- New girder top flange is laterally braced at mid span and at girder ends only.4- Columns are continuous from foundation to roof and are prevented from sway atfloor level and at roof level in both directions.5- Columns are pin supported at foundation, at floor level,…arrow_forward
- MATLAB: An Introduction with ApplicationsEngineeringISBN:9781119256830Author:Amos GilatPublisher:John Wiley & Sons IncEssentials Of Materials Science And EngineeringEngineeringISBN:9781337385497Author:WRIGHT, Wendelin J.Publisher:Cengage,Industrial Motor ControlEngineeringISBN:9781133691808Author:Stephen HermanPublisher:Cengage Learning
- Basics Of Engineering EconomyEngineeringISBN:9780073376356Author:Leland Blank, Anthony TarquinPublisher:MCGRAW-HILL HIGHER EDUCATIONStructural Steel Design (6th Edition)EngineeringISBN:9780134589657Author:Jack C. McCormac, Stephen F. CsernakPublisher:PEARSONFundamentals of Materials Science and Engineering...EngineeringISBN:9781119175483Author:William D. Callister Jr., David G. RethwischPublisher:WILEY





