Physics for Scientists and Engineers With Modern Physics
9th Edition
ISBN: 9781133953982
Author: SERWAY, Raymond A./
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 10, Problem 71AP
Review. A mixing beater consists of three thin rods, each 10.0 cm long. The rods diverge from a central hub, separated from each other by 120°, and all turn in the same plane. A ball is attached to the end of each rod. Each ball has cross-sectional area 4.00 cm2 and is so shaped that it has a drag coefficient of 0.600. Calculate the power input required to spin the beater at 1 000 rev/min (a) in air and (b) in water.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
9.2.3c
A flywheel is a solid disk that rotates about an axis that is perpendicular to the disk at its center. Rotating flywheels provide a means
for storing energy in the form of rotational kinetic energy and are being considered as a possible alternative to batteries in electric
cars. The gasoline burned in a 243-mile trip in a typical midsize car produces about 4.81 x 10° J of energy. How fast would a 46.7-kg
flywheel with a radius of 0.475 m have to rotate to store this much energy? Give your answer in rev/min.
Number
i
Units
A flywheel is a solid disk that rotates about an axis that is perpendicular to the disk at its center. Rotating flywheels provide a means for storing energy in the form of rotational kinetic energy and are being considered as a possible alternative to batteries in electric cars. The gasoline burned in a 144-mile trip in a typical midsize car produces about 1.05 x 109 J of energy. How fast would a 18.7-kg flywheel with a radius of 0.247 m have to rotate to store this much energy? Give your answer in rev/min.
Chapter 10 Solutions
Physics for Scientists and Engineers With Modern Physics
Ch. 10.1 - A rigid object rotates in a counterclockwise sense...Ch. 10.2 - Consider again the pairs of angular positions for...Ch. 10.3 - Ethan and Rebecca are riding on a merry-go-round....Ch. 10.4 - Prob. 10.4QQCh. 10.5 - You turn off your electric drill and find that the...Ch. 10.7 - A section of hollow pipe and a solid cylinder have...Ch. 10.9 - A ball rolls without slipping down incline A,...Ch. 10 - Prob. 1OQCh. 10 - Consider an object on a rotating disk a distance r...Ch. 10 - Prob. 3OQ
Ch. 10 - Prob. 4OQCh. 10 - Suppose a cars standard tires are replaced with...Ch. 10 - Figure OQ10.6 shows a system of four particles...Ch. 10 - Prob. 7OQCh. 10 - Prob. 8OQCh. 10 - Prob. 9OQCh. 10 - Prob. 10OQCh. 10 - A solid aluminum sphere of radius R has moment of...Ch. 10 - Prob. 1CQCh. 10 - Prob. 2CQCh. 10 - Prob. 3CQCh. 10 - Prob. 4CQCh. 10 - Prob. 5CQCh. 10 - Prob. 6CQCh. 10 - Prob. 7CQCh. 10 - Prob. 8CQCh. 10 - (a) What is the angular speed of the second hand...Ch. 10 - Prob. 10CQCh. 10 - Prob. 11CQCh. 10 - Prob. 12CQCh. 10 - Three objects of uniform densitya solid sphere, a...Ch. 10 - Which of the entries in Table 10.2 applies to...Ch. 10 - Prob. 15CQCh. 10 - Prob. 16CQCh. 10 - (a) Find the angular speed of the Earths rotation...Ch. 10 - Prob. 2PCh. 10 - Prob. 3PCh. 10 - A bar on a hinge starts from rest and rotates with...Ch. 10 - A wheel starts from rest and rotates with constant...Ch. 10 - Prob. 6PCh. 10 - Prob. 7PCh. 10 - A machine part rotates at an angular speed of...Ch. 10 - A dentists drill starts from rest. After 3.20 s of...Ch. 10 - Why is the following situation impossible?...Ch. 10 - Prob. 11PCh. 10 - The tub of a washer goes into its spin cycle,...Ch. 10 - Prob. 13PCh. 10 - Review. Consider a tall building located on the...Ch. 10 - Prob. 15PCh. 10 - Prob. 16PCh. 10 - A discus thrower (Fig. P10.9) accelerates a discus...Ch. 10 - Figure P10.18 shows the drive train of a bicycle...Ch. 10 - A wheel 2.00 m in diameter lies in a vertical...Ch. 10 - A car accelerates uniformly from rest and reaches...Ch. 10 - Prob. 21PCh. 10 - Prob. 22PCh. 10 - Prob. 23PCh. 10 - Prob. 24PCh. 10 - Prob. 25PCh. 10 - Review. A small object with mass 4.00 kg moves...Ch. 10 - Find the net torque on the wheel in Figure P10.14...Ch. 10 - Prob. 28PCh. 10 - An electric motor turns a flywheel through a drive...Ch. 10 - A grinding wheel is in the form of a uniform solid...Ch. 10 - Prob. 31PCh. 10 - Review. A block of mass m1 = 2.00 kg and a block...Ch. 10 - Prob. 33PCh. 10 - Prob. 34PCh. 10 - Prob. 35PCh. 10 - Prob. 36PCh. 10 - A potters wheela thick stone disk of radius 0.500...Ch. 10 - Imagine that you stand tall and turn about a...Ch. 10 - Prob. 39PCh. 10 - Two balls with masses M and m are connected by a...Ch. 10 - Prob. 41PCh. 10 - Following the procedure used in Example 10.7,...Ch. 10 - Three identical thin rods, each of length L and...Ch. 10 - Rigid rods of negligible mass lying along the y...Ch. 10 - Prob. 45PCh. 10 - Prob. 46PCh. 10 - A war-wolf or trebuchet is a device used during...Ch. 10 - Prob. 48PCh. 10 - Big Ben, the nickname for the clock in Elizabeth...Ch. 10 - Consider two objects with m1 m2 connected by a...Ch. 10 - The top in Figure P10.51 has a moment of inertia...Ch. 10 - Prob. 52PCh. 10 - Prob. 53PCh. 10 - Prob. 54PCh. 10 - Review. An object with a mass of m = 5.10 kg is...Ch. 10 - This problem describes one experimental method for...Ch. 10 - A uniform solid disk of radius R and mass M is...Ch. 10 - Prob. 58PCh. 10 - Prob. 59PCh. 10 - Prob. 60PCh. 10 - (a) Determine the acceleration of the center of...Ch. 10 - A smooth cube of mass m and edge length r slides...Ch. 10 - Prob. 63PCh. 10 - A tennis ball is a hollow sphere with a thin wall....Ch. 10 - Prob. 65PCh. 10 - Prob. 66APCh. 10 - Prob. 67APCh. 10 - Prob. 68APCh. 10 - Prob. 69APCh. 10 - Prob. 70APCh. 10 - Review. A mixing beater consists of three thin...Ch. 10 - Prob. 72APCh. 10 - Prob. 73APCh. 10 - Prob. 74APCh. 10 - Prob. 75APCh. 10 - Prob. 76APCh. 10 - Review. As shown in Figure P10.77, two blocks are...Ch. 10 - Review. A string is wound around a uniform disk of...Ch. 10 - Prob. 79APCh. 10 - Prob. 80APCh. 10 - Prob. 81APCh. 10 - Review. A spool of wire of mass M and radius R is...Ch. 10 - A solid sphere of mass m and radius r rolls...Ch. 10 - Prob. 84APCh. 10 - Prob. 85APCh. 10 - Review. A clown balances a small spherical grape...Ch. 10 - A plank with a mass M = 6.00 kg rests on top of...Ch. 10 - Prob. 88CPCh. 10 - Prob. 89CPCh. 10 - Prob. 90CPCh. 10 - A spool of thread consists of a cylinder of radius...Ch. 10 - A cord is wrapped around a pulley that is shaped...Ch. 10 - Prob. 93CPCh. 10 - A uniform, hollow, cylindrical spool has inside...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A cam of mass M is in the shape of a circular disk of diameter 2R with an off-center circular hole of diameter R is mounted on a uniform cylindrical shaft whose diameter matches that of the hole (Fig. P1 3.78). a. What is the rotational inertia of the cam and shaft around the axis of the shaft? b. What is the rotational kinetic energy of the cam and shaft if the system rotates with angular speed around this axis?arrow_forwardThe puck in Figure P11.46 has a mass of 0.120 kg. The distance of the puck from the center of rotation is originally 40.0 cm, and the puck is sliding with a speed of 80.0 cm/s. The string is pulled downward 15.0 cm through the hole in the frictionless table. Determine the work done on the puck. (Suggestion: Consider the change of kinetic energy.) Figure P11.46arrow_forwardA tennis ball is a hollow sphere with a thin wall. It is set rolling without slipping at 4.03 m/s on a horizontal section of a track as shown in Figure P10.62. It rolls around the inside of a vertical circular loop of radius r = 45.0 cm. As the ball nears the bottom of the loop, the shape of the track deviates from a perfect circle so that the ball leaves the track at a point h = 20.0 cm below the horizontal section. (a) Find the balls speed at the top of the loop. (b) Demonstrate that the ball will not fall from the track at the top of the loop. (c) Find the balls speed as it leaves the track at the bottom. What If? (d) Suppose that static friction between ball and track were negligible so that the ball slid instead of rolling. Would its speed then be higher, lower, or the same at the top of the loop? (e) Explain your answer to part (d). Figure P10.62arrow_forward
- A disk with moment of inertia I1 rotates about a frictionless, vertical axle with angular speed i. A second disk, this one having moment of inertia I2 and initially not rotating, drops onto the first disk (Fig. P10.50). Because of friction between the surfaces, the two eventually reach the same angular speed f. (a) Calculate f. (b) Calculate the ratio of the final to the initial rotational energy. Figure P10.50arrow_forwardConsider two objects with m1 m2 connected by a light string that passes over a pulley having a moment of inertia of I about its axis of rotation as shown in Figure P10.44. The string does not slip on the pulley or stretch. The pulley turns without friction. The two objects are released from rest separated by a vertical distance 2h. (a) Use the principle of conservation of energy to find the translational speeds of the objects as they pass each other. (b) Find the angular speed of the pulley at this time.arrow_forwardAn electric motor turns a flywheel through a drive belt that joins a pulley on the motor and a pulley that is rigidly attached to the flywheel as shown in Figure P10.37. The flywheel is a solid disk with a mass of 80.0 kg and a radius R = 0.625 m. It turns on a frictionless axle. Its pulley has much smaller mass and a radius of r = 0.230 m. The tension Tu in the upper (taut) segment of the belt is 135 N, and the flywheel has a clockwise angular acceleration of 1.67 rad/s2. Find the tension in the lower (slack) segment of the belt. Figure P10.37arrow_forward
- As shown in Figure OQ10.9, a cord is wrapped onto a cylindrical reel mounted on a fixed, frictionless, horizontal axle. When does the reel have a greater magnitude of angular acceleration? (a) When the cord is pulled down with a constant force of 50 N. (b) When an object of weight 50 N is hung from the cord and released. (c) The angular accelerations in parts (a) and (b) are equal. (d) It is impossible to determine. Figure OQ10.9arrow_forwardIn Figure P10.40, the hanging object has a mass of m1 = 0.420 kg; the sliding block has a mass of m2 = 0.850 kg; and the pulley is a hollow cylinder with a mass of M = 0.350 kg, an inner radius of R1 = 0.020 0 m, and an outer radius of R2 = 0.030 0 m. Assume the mass of the spokes is negligible. The coefficient of kinetic friction between the block and the horizontal surface is k = 0.250. The pulley turns without friction on its axle. The light cord does not stretch and does not slip on the pulley. The block has a velocity of vi = 0.820 m/s toward the pulley when it passes a reference point on the table. (a) Use energy methods to predict its speed after it has moved to a second point, 0.700 m away. (b) Find the angular speed of the pulley at the same moment. Figure P10.40arrow_forwardReview. An object with a mass of m = 5.10 kg is attached to the free end of a light string wrapped around a reel of radius R = 0.250 m and mass M = 3.00 kg. The reel is a solid disk, free to rotate in a vertical plane about the horizontal axis passing through its center as shown in Figure P10.45. The suspended object is released from rest 6.00 m above the floor. Determine (a) the tension in the string, (b) the acceleration of the object, and (c) the speed with which the object hits the floor. (d) Verify your answer to part (c) by using the isolated system (energy) model. Figure P10.45arrow_forward
- In testing an automobile tire for proper alignment, a technicianmarks a spot on the tire 0.200 m from the center. He then mountsthe tire in a vertical plane and notes that the radius vector to thespot is at an angle of 35.0 with the horizontal. Starting from rest,the tire is spun rapidly with a constant angular acceleration of 3.00 rad/s2. a. What is the angular speed of the wheel after 4.00 s? b. What is the tangential speed of the spot after 4.00 s? c. What is the magnitude of the total accleration of the spot after 4.00 s?" d. What is the angular position of the spot after 4.00 s?arrow_forwardFind the net torque on the wheel in Figure P10.23 about the axle through O, taking a = 10.0 cm and b = 25.0 cm. Figure P10.23arrow_forwardA tennis ball is a hollow sphere with a thin wall. It is set rolling without slipping at 4.03 m/s on a horizontal section of a track as shown in Figure P10.33. It rolls around the inside of a vertical circular loop of radius r = 45.0 cm. As the ball nears the bottom of the loop, the shape of the track deviates from a perfect circle so that the ball leaves the track at a point h = 20.0 cm below the horizontal section. (a) Find the balls speed at the top of the loop. (b) Demonstrate that the ball will not fall from the track at the top of the loop. (c) Find the balls speed as it leaves the track at the bottom. (d) What If? Suppose that static friction between ball and track were negligible so that the ball slid instead of rolling. Describe the speed of the ball at the top of the loop in this situation. (e) Explain your answer to part (d). Figure P10.33arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Glencoe Physics: Principles and Problems, Student...PhysicsISBN:9780078807213Author:Paul W. ZitzewitzPublisher:Glencoe/McGraw-Hill
Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Glencoe Physics: Principles and Problems, Student...
Physics
ISBN:9780078807213
Author:Paul W. Zitzewitz
Publisher:Glencoe/McGraw-Hill
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Rotational Kinetic Energy; Author: AK LECTURES;https://www.youtube.com/watch?v=s5P3DGdyimI;License: Standard YouTube License, CC-BY