A 2.00 kg stone is tied to a thin, light wire wrapped around the outer edge of the uniform 10.0 kg cylindrical pulley shown in Figure 10.46. The inner diameter of the pulley is 60.0 cm, while the outer diameter is 1.00 m. The system is released from rest, and there is no friction at the axle of the pulley. Find (a) the acceleration of the stone, (b) the tension in the wire, and (c) the
Figure 10.46
Problem 11.
Want to see the full answer?
Check out a sample textbook solutionChapter 10 Solutions
College Physics (10th Edition)
Additional Science Textbook Solutions
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
Life in the Universe (4th Edition)
Essential University Physics (3rd Edition)
University Physics with Modern Physics (14th Edition)
Sears And Zemansky's University Physics With Modern Physics
Introduction to Electrodynamics
- Find the net torque on the wheel in Figure P10.23 about the axle through O, taking a = 10.0 cm and b = 25.0 cm. Figure P10.23arrow_forwardYou pull downward with a force of 32 N on a rope that passes over a disk-shaped pulley of mass 1.3 kg and radius 0.075 m. The other end of the rope is attached to a 0.60 kg mass. Find the linear acceleration of the 0.60 kg mass.arrow_forwardA sphere of mass 5 kg and a block of mass m2 =3 kg are connected by a light cord that passes over a pulley as shown in Figure. The radius of the pulley is R=20 cm, and the mass of the thin rim is 1 kg. The spokes of the pulley have negligible mass. The block slides on a horizontal surface. The kinetic coefficient of friction between block and horizontal surface is 0.1 Find for the linear acceleration of the two objects,arrow_forward
- To loosen a rusty nut, a 20.00-N force is applied to the wrench handle at angle ϕ=40° and at a distance of 0.25 m from the nut. Find the magnitude and direction of the torque applied to the nut.arrow_forwardYou pull downward with a force of 30 N on a rope that passes over a disk-shaped pulley of mass 1.5 kg and radius 0.075 m. The other end of the rope is attached to a 0.67 kg mass. Find the tension in the rope on both sides of the pulley.arrow_forwardYou have a pulley 10.2 cm in diameter and with a mass of 2.1 kg. You get to wondering whether the pulley is uniform. That is, is the mass evenly distributed, or is it concentrated toward the center or the rim? To find out, you hang the pulley on a hook, wrap a string around it several times, and suspend your 1.2 kg physics book 1.1 m above the floor. With your stopwatch, you can find that it takes 0.65 s for your book to hit the floor. Use g=9.8 m/s?. What is the moment of inertia if the pulley is uniform? | kg m² What is the actual moment of inertia of the pulley based on your measurement? kg m2 What do you conclude about the pulley? O The pulley is uniform (within 1% of uniform) O The mass of the pulley is concentrated toward the center O The mass of the pulley is concentrated toward the rimarrow_forward
- You have a pulley 13.9 cm in diameter and with a mass of 1.3 kg. You get to wondering whether the pulley is uniform. That is, is the mass evenly distributed, or is it concentrated toward the center or the rim? To find out, you hang the pulley on a hook, wrap a string around it several times, and suspend your 1.3 kg physics book 1.5 m above the floor. With your stopwatch, you can find that it takes 0.74 s for your book to hit the floor. Use g=9.8 m/s². What is the moment of inertia if the pulley is uniform? kg m² What is the actual moment of inertia of the pulley based on your measurement? kg m2 What do you conclude about the pulley? The pulley is uniform (within 1% of uniform) The mass of the pulley is concentrated toward the center The mass of the pulley is concentrated toward the rimarrow_forwardAs a torque activity, your Physics TA sets up the arrangement shown below. A uniform rod of mass mr = 143 g and length L = 100.0 cm is attached to the wall with a pin as shown. Cords are attached to the rod at the r1 = 10.0 cm and r2 = 90.0 cm mark, passed over pulleys, and masses of m1 = 286 g and m2 = 177 g are attached. Your TA asks you to determine the following. (a) The position r3 on the rod where you would suspend a mass m3 = 200 g in order to balance the rod and keep it horizontal if released from a horizontal position. In addition, for this case, what force (magnitude and direction) does the pin exert on the rod? Use standard angle notation to determine the direction of the force the pin exerts on the rod. Express the direction of the force the pin exerts on the rod as the angle ?F, measured with respect to the positive x-axis (counterclockwise is positive and clockwise is negative). r3 = m Fp = N ?F = ° (b) Let's now remove the mass m3 and determine the new…arrow_forwardA 50.0 kg grindstone is a solid disk 0.520 m in diameter. You press an ax down on the rim with a normal force of 160 N (Fig. ). The coefficient of kinetic friction between the blade and the stone is 0.60, and there is a constant friction torque of 6.50 N . m between the axle of the stone and its bearings. (a) How much force must be applied tangentially at the end of a crank handle 0.500 m long to bring the stone from rest to 120 rev/min in 9.00 s? (b) After the grindstone attains an angular speed of 120 rev/min, what tangential force at the end of the handle is needed to maintain a constant angular speed of 120 rev/min? (c) How much time does it take the grindstone to come from 120 rev/min to rest if it is acted on by the axle friction alone?arrow_forward
- A way to test the tensile strength of a wire is to place a mass at the end of it and spin the mass with uniform circular motion. The speed at which the wire breaks is a measure of its strength. The maximum frequency of rotation before a certain wire breaks is 35.5 Hz. The wire is 50.5 cm long and has a mass of 0.656 kg. (a) Determine the speed with which the mass moves. (b) Calculate the centripetal force acting on the wirearrow_forwardJohn is pushing his daughter Rachel in a wheelbarrow when it is stopped by a brick 8.00 cm high (see the figure below). The handles make an angle of 0 = 20.0° with the ground. Due to the weight of Rachel and the wheelbarrow, a downward force of 407 N is exerted at the center of the wheel, which has a radius of 18.0 cm. Assume the brick remains fixed and does not slide along the ground. Also assume the force applied by John is directed exactly toward the center of the wheel. (Choose the positive x-axis to be pointing to the right.) & (a) What force (in N) must John apply along the handles to just start the wheel over the brick? 1690.53 X Your response differs from the correct answer by more than 10%. Double check your calculations. N (b) What is the force (magnitude in kN and direction in degrees clockwise from the -x-axis) that the brick exerts on the wheel just as the wheel begins to lift over the brick? magnitude KN direction ° clockwise from the -x-axisarrow_forwardJohn is pushing his daughter Rachel in a wheelbarrow when it is stopped by a brick 8.00 cm high (see the figure below). The handles make an angle of 0 = 18.5° with the ground. Due to the weight of Rachel and the wheelbarrow, a downward force of 403 N is exerted at the center of the wheel, which has a radius of 15.0 cm. Assume the brick remains fixed and does not slide along the ground. Also assume the force applied by John is directed exactly toward the center of the wheel. (Choose the positive x-axis to be pointing to the right.) (a) What force (in N) must John apply along the handles to just start the wheel over the brick? (b) What is the force (magnitude in kN and direction in degrees clockwise from the -x-axis) that the brick exerts on the wheel just as the wheel begins to lift over the brick? magnitude kN direction ° clockwise from the -x-axisarrow_forward
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning