Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 1, Problem 37P
From Appendix A, the viscosity μ(N·s/m2) of water at temperature T(K) can be computed from μ = A10B/(T − C), where A = 2.414 × 10−5 N·s/m2, B = 247.8 K, and C =140 K. Determine the viscosity of water at 30°C, and estimate its uncertainty if the uncertainty in temperature measurement is ±0.5°C.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The variation of the dynamic viscosity of water with absolute temperature is given as Using these tabulated data, develop a relation for viscosity in the form of ? = ? (T ) = A + BT + CT2 + DT3 + ET4. Using the relation developed, predict the dynamic viscosity of water at 50°C at which the reported value is 5.468 × 10−4 Pa⋅s. Compare your result with the results of Andrade’s equation, which is given in the form of ? = D⋅eB/T, where D and B are constants whose values are to be determined using the viscosity data given.
Problem 3: A honeybee farmer wants to measure the absolute viscosity of his honey. You suggest
dropping a 4mm steel ball into a container of honey and measure the time it takes for the ball to pass
between two marks as shown. If the time is 13 seconds, what is the honey's viscosity. Assume the
density of the honey is 1450 kg/m3 and the density of the steel ball is 7800 kg/m³.
Honey
5 cm
Q1.
A concentric cylinder viscometer is driven by a falling mass M connected by
a cord and pulley to the inner cylmder. Annular gap of width a and height H has
been filled with liquid to be tested. The speed of the falling mass is Vim. Develop an
algebraic expression for the viscosity of the liquid. Evaluate the viscosity of the
liquid using M= 0.1 Kg, R=50mm, H=80 mm, r-25mm, =0.20mm and Vim = 30 +
ww
XX
Cord
Puliey,
Chapter 1 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 1 - A number of common substances are Some of these...Ch. 1 - Give a word statement of each of the five basic...Ch. 1 - The barrel of a bicycle tire pump becomes quite...Ch. 1 - Very small particles moving in fluids are known to...Ch. 1 - In a combustion process, gasoline particles are to...Ch. 1 - In a pollution control experiment, minute solid...Ch. 1 - A rocket payload with a weight on earth of 2000 lb...Ch. 1 - A cubic metre of air at 101 kPa absolute and 15C...Ch. 1 - Calculate the specific weight, specific volume,...Ch. 1 - For Problem 1.6, find the distance the particles...
Ch. 1 - A sky diver with a mass of 70 kg jumps from an...Ch. 1 - The English perfected the longbow as a weapon...Ch. 1 - For each quantity listed, indicate dimensions...Ch. 1 - The density of a sample of sea water is 1.99...Ch. 1 - A pump is rated at 50 hp. What is the rating in kW...Ch. 1 - A fluid occupying 3.2m3 has a mass of 4 Mg....Ch. 1 - If a power plant is rated at 2000 MW output and...Ch. 1 - For each quantity listed, indicate dimensions...Ch. 1 - Derive the following conversion factors: (a)...Ch. 1 - Express the following in SI units: (a) 5 acreft...Ch. 1 - Express the following in SI units: (a) 100...Ch. 1 - Express the following in BG units: (a) 50 m2 (b)...Ch. 1 - While youre waiting for the ribs to cook, you muse...Ch. 1 - Derive the following conversion factors: (a)...Ch. 1 - The kilogram force is commonly used in Europe as a...Ch. 1 - From thermodynamics, we know that the coefficient...Ch. 1 - The maximum theoretical flow rate (slug/s) through...Ch. 1 - The mean free path of a molecule of gas is the...Ch. 1 - A container weighs 3.5 lbf when empty. When filled...Ch. 1 - A parameter that is often used in describing pump...Ch. 1 - Calculate the density of standard air in a...Ch. 1 - The mass of the standard American golf ball is...Ch. 1 - A can of pet food has the following internal...Ch. 1 - The mass flow rate in a water flow system...Ch. 1 - The mass flow rate of water in a tube is measured...Ch. 1 - The mass of the standard British golf ball is 45.9...Ch. 1 - From Appendix A, the viscosity (Ns/m2) of water at...Ch. 1 - An enthusiast magazine publishes data from its...Ch. 1 - The height of a building may be estimated by...Ch. 1 - An American golf ball is described in Problem 1.32...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Find the heat transfer in Problem 4.13.
Fundamentals Of Thermodynamics
What is the source of the welding heat in thermit welding?
DeGarmo's Materials and Processes in Manufacturing
If x = 8 m, vx = 8 m/s, and ax = 4 m/s2 when t = 2 s, determine the magnitude of the particles velocity and acc...
Engineering Mechanics: Dynamics (14th Edition)
If the maximum force in each rod con not exceed 1500 N, determine the greatest mass of the crate that can be su...
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Determine the force developed in the short link BD, and She tension in the cords CE and CF, and the reactions o...
Engineering Mechanics: Statics
Water at 10 C flows at the rate of 900 L/min from the reservoir and through the pipe shown in Fig. 8.16. Comput...
Applied Fluid Mechanics (7th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In medical work, pressures are often measured in units of mm of H2O because body fluids, including the cerebrospinal fluid, typically have nearly the same density as water. The pressure of the cerebrospinal fluid can be measured by means of a spinal tap. A hollow tube is inserted into the spinal column, and the height to which the fluid rises is observed. If the fluid rises to a height of 160 mm, we write its gauge pressure as 160 mm H2O. (a) Express this pressure in pascals, in atmospheres, and in millimeters of mercury.arrow_forwardIn medical work, pressures are often measured in units of mm of H2O because body fluids, including the cerebrospinal fluid, typically have nearly the same density as water. The pressure of the cerebrospinal fluid can be measured by means of a spinal tap. A hollow tube is inserted into the spinal column, and the height to which the fluid rises is observed. If the fluid rises to a height of 160 mm, we write its gauge pressure as 160 mm H2O. a) Sometimes it is necessary to determine whether an accident victim has suffered a crushed vertebra that is blocking the flow of cerebrospinal fluid in the spinal column. In other cases, a physician may suspect that a tumor or other growth is locking the spinal column and inhibiting the flow of cerebrospinal fluid. Such conditions can be investigated by means of the Queckensted test. In this procedure the veins in the patient’s neck are compressed, to make the blood pressure rise in the brain. The increase in pressure in the blood vessels is…arrow_forward! Required information The dynamic viscosity of air at 20°C is u≈ 1.80E-5 Pa-s. Estimate the viscosity of air at various temperatures by the below mentioned methods. Determine the viscosity of air at 500°C by the Law of Corresponding States. E-5 kg/(m.s)arrow_forward
- The viscosity of liquids is appreciably affected by a change in temperature. Select one: True Falsearrow_forwardI need handuwritten solution. Strictly don't use chatgpt.arrow_forwardA capillary rise experiment is proposed for a high school physics class. The students are told that for water in clean glass tubes, the contact angle between liquid and glass (θ)is 90°. The students are asked to measure capillary rise in a series of tube diameters (D=0.02, 0.04, 0.06, 0.08, and 0.10 in.). They are then asked to graph the results and determine the approximate tube diameters that would produce capillary rises of 1.5, 1.0, and 0.5 in. Predict the results if the water used in the experiment is at 20°C. The Provided answers for h=1.5 in D=0.0301 inforh=1.0 in D=0.0452 infor h=0.5 in,D=0.0904 in Can not figure this out .arrow_forward
- At a certain point on the wing of the aircraft, the pressure is 37,803 Pa and the density is 45% of the standard sea level values. Determine the temperature (Kelvin) at that point? Use standard metric units and round off answer to the nearest hundredths.arrow_forwardA single-cylinder rotational viscometer is used to measurea liquid with viscosity of 100 cP using a spindle with 6 cmlength and 1 cm radius. At maximum shear rate (rpm560),the measurements approach a full-scale reading of 100.Determine the spindle dimensions that will allow theviscometer to measure viscosities up to 10,000 cP atmaximum shear rate. Answer is 1.293 cmarrow_forward(Dimensional Analysis) If the velocity V in a fluid flow depends on a dimension 1, the fluid density p, and the viscosity µ, show that this implies that the Reynolds number Vlp/µ is constant.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Properties of Fluids: The Basics; Author: Swanson Flo;https://www.youtube.com/watch?v=TgD3nEO1iCA;License: Standard YouTube License, CC-BY
Fluid Mechanics-Lecture-1_Introduction & Basic Concepts; Author: OOkul - UPSC & SSC Exams;https://www.youtube.com/watch?v=6bZodDnmE0o;License: Standard Youtube License