Applied Fluid Mechanics (7th Edition)
7th Edition
ISBN: 9780132558921
Author: Robert L. Mott, Joseph A. Untener
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 1, Problem 1.113PP
A cylindrical tank has a diameter of 38 in with its axis vertical. Determine the depth of fluid in the tank when it is holding 85 gal of fluid.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Continuity equation
A
y
x
dx
D
T
معادلة الاستمرارية
Ly
X
Q/Prove that
ди
хе
+ ♥+ ㅇ?
he
me
ze
ོ༞“༠ ?
Q
Derive (continuity equation)?
I want to derive clear mathematics.
motor supplies 200 kW at 6 Hz to flange A of the shaft shown in Figure. Gear B transfers 125 W of power to operating machinery in the factory, and the remaining power in the shaft is mansferred by gear D. Shafts (1) and (2) are solid aluminum (G = 28 GPa) shafts that have the same diameter and an allowable shear stress of t= 40 MPa. Shaft (3) is a solid steel (G = 80 GPa) shaft with an allowable shear stress of t = 55 MPa. Determine:
a) the minimum permissible diameter for aluminum shafts (1) and (2)
b) the minimum permissible diameter for steel shaft (3).
c) the rotation angle of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b).
Chapter 1 Solutions
Applied Fluid Mechanics (7th Edition)
Ch. 1 - 1.1 Convert 1250 millimeters to meters.Ch. 1 - Convert 1600 square millimeters to square metersCh. 1 - Convert 3.65x103 cubic millimeters to cubic metersCh. 1 - Convert 2.05 square meters to square millimetersCh. 1 - Convert 0.391 cubic meters to cubic millimetersCh. 1 - Convert 55.0 gallons to cubic metersCh. 1 - An automobile is moving at 80 kilometers per hour,...Ch. 1 - Convert a length of 25.3 feet to metersCh. 1 - Convert a distance of 1.36 miles to meters.Ch. 1 - Convert a length of 3.65 inches to millimeters.
Ch. 1 - Convert a distance of 2580 feet to meters.Ch. 1 - Convert a volume of 480 cubic feet to cubic...Ch. 1 - Convert a volume of 7390 cubic centimeters to...Ch. 1 - Convert a volume of 6.35 liters to cubic nneters.Ch. 1 - Convert 6.0 feet per second to meters per secondCh. 1 - Convert 2500 cubic feet per minute to cubic meters...Ch. 1 - A car travels 0.50 km in 10.6 s. Calculate its...Ch. 1 - In an attempt at a land speed record, a car...Ch. 1 - A car travels 1000 ft in 14 s. Calculate its...Ch. 1 - In an attempt at a land speed record, a car...Ch. 1 - A body starting from rest with constant...Ch. 1 - A body starting from rest with constant...Ch. 1 - A body starting from rest with constant...Ch. 1 - A body starting from rest with constant...Ch. 1 - The formula for kinetic energy is KE=mv2, where m...Ch. 1 - The formula for kinetic energy is KE=12mv2, where...Ch. 1 - The formula for kinetic energy is KE=12mv2, where...Ch. 1 - The formula for kinetic energy is KE=12mv2, where...Ch. 1 - The formula for kinetic energy is KE=12mv2, where...Ch. 1 - The formula for kinetic energy is KE=12mv2 where m...Ch. 1 - The formula for kinetic energy is KE=12mv2, where...Ch. 1 - The formula for kinetic energy is KE=12mv2, where...Ch. 1 - The formula for kinetic energy is KE=12mv2, where...Ch. 1 - The formula for kinetic energy is KE=12mv2, where...Ch. 1 - The formula for kinetic energy is KE=12mv2, where...Ch. 1 - The formula for kinetic energy is where m = mass...Ch. 1 - The formula for kinetic energy is KE=12mv2, where...Ch. 1 - The formula for kinetic energy is KE=12mv2, where...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - One measure of a baseball pitcher's performance is...Ch. 1 - Compute the pressure change required to cause a...Ch. 1 - Compute the pressure change required to cause a...Ch. 1 - Compute the pressure change required to cause a...Ch. 1 - For the conditions described in Problem 1.59...Ch. 1 - A certain hydraulic system operates at 3000 psi....Ch. 1 - A certain hydraulic system operates at 20.0 MPa....Ch. 1 - A measure of the stiffness of a linear actuator...Ch. 1 - 1.64 Repeat Problem 1.63 but change the length of...Ch. 1 - Repeat Problem 1.6319 but change the cylinder...Ch. 1 - Using the results of Problems 1.63-1.65, generate...Ch. 1 - Calculate the mass of a can of oil if it weighs...Ch. 1 - Calculate the mass of a tank of gasoline if it...Ch. 1 - '1.69 Calculate the weight of 1m3 of kerosene if...Ch. 1 - Calculate the weight of a jar of castor oil if it...Ch. 1 - Calculate the mass of 1 gal of oil if it weighs...Ch. 1 - Calculate the mass of 1ft3 of gasoline if it...Ch. 1 - Calculate the weight of 1ft3 of kerosene if it has...Ch. 1 - Calculate the weight of 1 gal of water if it has a...Ch. 1 - Assume that a man weighs 160 lb (force) Compute...Ch. 1 - In the United States, hamburger and other meats...Ch. 1 - The metric ton is 1000 kg (mass). Compute the...Ch. 1 - Convert the force found in Problem 1.77 to lb.Ch. 1 - Determine your weight in lb and N and your mass in...Ch. 1 - The specific gravity of benzene is 0.876....Ch. 1 - Air at 16 C and standard atmospheric pressure has...Ch. 1 - Carbon dioxide has a density of 1.964kg/m3 at 0 C....Ch. 1 - A certain medium lubricating oil has a specific...Ch. 1 - At 100 C mercury has a specific weight of...Ch. 1 - A cylindrical can 150 mm in diameter is filled to...Ch. 1 - Glycerin has a specific gravity of 1.258. How much...Ch. 1 - The fuel tank of an automobile holds 0.095m3. If...Ch. 1 - The density of muriatic acid is 1200 kg / m3...Ch. 1 - Liquid ammonia has a specific gravity of 0.826....Ch. 1 - Vinegar has a density of 1080 kg / m3 Calculate...Ch. 1 - Methyl alcohol has a specific gravity of 0.789....Ch. 1 - A cylindrical container is 150 mm in diameter and...Ch. 1 - A storage vessel for gasoline ( sg=0.68 ) is a...Ch. 1 - What volume of mercury (sg = 13.54) would weigh...Ch. 1 - A rock has a specific gravity of 2.32 and a volume...Ch. 1 - The specific gravity of benzene is 0.876....Ch. 1 - Air at 59 F and standard atmospheric pressure has...Ch. 1 - Carbon dioxide has a density of 0.003 81 slug/ft3...Ch. 1 - A certain medium lubricating oil has a specific...Ch. 1 - At 212F mercury has a specific weight of 834...Ch. 1 - One gallon of a certain fuel oil weighs 7.50 lb....Ch. 1 - Glycerin has a specific gravity of 1.258. How much...Ch. 1 - The fuel tank of an automobile holds 25.0 gal. If...Ch. 1 - The density of muriatic acid is 1.20 g/cm3....Ch. 1 - Liquid ammonia has a specific gravity of 0.826....Ch. 1 - Vinegar has a density of 1.08 g/cm3. Calculate its...Ch. 1 - Alcohol has a specific gravity of 0.79. Calculate...Ch. 1 - A cylindrical container has a 6.0-in diameter and...Ch. 1 - A storage vessel for gasoline (sg = 0.68) is a...Ch. 1 - How many gallons of mercury (sg = 13.54) would...Ch. 1 - A rock has a specific gravity of 2.32 and a volume...Ch. 1 - A village of 75 people desires a tank to store a...Ch. 1 - A cylindrical tank has a diameter of 38 in with...Ch. 1 - What is the required rate, in N/min, to empty a...Ch. 1 - An empty tank measuring 1.5 m by 2.5 m on the...Ch. 1 - A tank that is 2 ft in diameter and 18 in tall is...Ch. 1 - A standard pump design can be upgraded to higher...Ch. 1 - What is the annual cost to run a 2 HP system if it...Ch. 1 - Determine the displacement, in liters, for one...Ch. 1 - Determine the flow rate, in m3/hr, for another...Ch. 1 - At what speed, in rpm, does a single cylinder pump...Ch. 1 - Prob. 2CAEA
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- First monthly exam Gas dynamics Third stage Q1/Water at 15° C flow through a 300 mm diameter riveted steel pipe, E-3 mm with a head loss of 6 m in 300 m length. Determine the flow rate in pipe. Use moody chart. Q2/ Assume a car's exhaust system can be approximated as 14 ft long and 0.125 ft-diameter cast-iron pipe ( = 0.00085 ft) with the equivalent of (6) regular 90° flanged elbows (KL = 0.3) and a muffler. The muffler acts as a resistor with a loss coefficient of KL= 8.5. Determine the pressure at the beginning of the exhaust system (pl) if the flowrate is 0.10 cfs, and the exhaust has the same properties as air.(p = 1.74 × 10-3 slug/ft³, u= 4.7 x 10-7 lb.s/ft²) Use moody chart (1) MIDAS Kel=0.3 Q3/Liquid ammonia at -20°C is flowing through a 30 m long section of a 5 mm diameter copper tube(e = 1.5 × 10-6 m) at a rate of 0.15 kg/s. Determine the pressure drop and the head losses. .μ= 2.36 × 10-4 kg/m.s)p = 665.1 kg/m³arrow_forward2/Y Y+1 2Cp Q1/ Show that Cda Az x P1 mactual Cdf Af R/T₁ 2pf(P1-P2-zxgxpf) Q2/ A simple jet carburetor has to supply 5 Kg of air per minute. The air is at a pressure of 1.013 bar and a temperature of 27 °C. Calculate the throat diameter of the choke for air flow velocity of 90 m/sec. Take velocity coefficient to be 0.8. Assume isentropic flow and the flow to be compressible. Quiz/ Determine the air-fuel ratio supplied at 5000 m altitude by a carburetor which is adjusted to give an air-fuel ratio of 14:1 at sea level where air temperature is 27 °C and pressure is 1.013 bar. The temperature of air decreases with altitude as given by the expression The air pressure decreases with altitude as per relation h = 19200 log10 (1.013), where P is in bar. State any assumptions made. t = ts P 0.0065harrow_forward36 2) Use the method of MEMBERS to determine the true magnitude and direction of the forces in members1 and 2 of the frame shown below in Fig 3.2. 300lbs/ft member-1 member-2 30° Fig 3.2. https://brightspace.cuny.edu/d21/le/content/433117/viewContent/29873977/Viewarrow_forward
- Can you solve this for me?arrow_forward5670 mm The apartment in the ground floor of three floors building in Fig. in Baghdad city. The details of walls, roof, windows and door are shown. The window is a double glazing and air space thickness is 1.3cm Poorly Fitted-with Storm Sash with wood strip and storm window of 0.6 cm glass thickness. The thickness of door is 2.5 cm. The door is Poor Installation. There are two peoples in each room. The height of room is 280 cm. assume the indoor design conditions are 25°C DBT and 50 RH, and moisture content of 8 gw/kga. The moisture content of outdoor is 10.5 gw/kga. Calculate heat gain for living room : الشقة في الطابق الأرضي من مبنى ثلاثة طوابق في مدينة بغداد يظهر في مخطط الشقة تفاصيل الجدران والسقف والنوافذ والباب. النافذة عبارة عن زجاج مزدوج وسمك الفراغ الهوائي 1.3 سم ضعيف الاحكام مع ساتر حماية مع إطار خشبي والنافذة بسماكة زجاج 0.6 سم سماكة الباب 2.5 سم. الباب هو تركيب ضعيف هناك شخصان في كل غرفة. ارتفاع الغرفة 280 سم. افترض أن ظروف التصميم الداخلي هي DBT25 و R50 ، ومحتوى الرطوبة 8…arrow_forwardHow do i solve this problem?arrow_forward
- Q4/ A compressor is driven motor by mean of a flat belt of thickness 10 mm and a width of 250 mm. The motor pulley is 300 mm diameter and run at 900 rpm and the compressor pulley is 1500 mm diameter. The shaft center distance is 1.5 m. The angle of contact of the smaller pulley is 220° and on the larger pulley is 270°. The coefficient of friction between the belt and the small pulley is 0.3, and between the belt and the large pulley is 0.25. The maximum allowable belt stress is 2 MPa and the belt density is 970 kg/m³. (a) What is the power capacity of the drive and (b) If the small pulley replaced by V-grooved pulley of diameter 300 mm, grooved angle of 34° and the coefficient of friction between belt and grooved pulley is 0.35. What will be the power capacity in this case, assuming that the diameter of the large pulley remain the same of 1500 mm.arrow_forwardYou are tasked with designing a power drive system to transmit power between a motor and a conveyor belt in a manufacturing facility as illustrated in figure. The design must ensure efficient power transmission, reliability, and safety. Given the following specifications and constraints, design drive system for this application: Specifications: Motor Power: The electric motor provides 10 kW of power at 1,500 RPM. Output Speed: The output shaft should rotate at 150 rpm. Design Decisions: Transmission ratio: Determine the necessary drive ratio for the system. Shaft Diameter: Design the shafts for both the motor and the conveyor end. Material Selection: Choose appropriate materials for the gears, shafts. Bearings: Select suitable rolling element bearings. Constraints: Space Limitation: The available space for the gear drive system is limited to a 1-meter-long section. Attribute 4 of CEP Depth of knowledge required Fundamentals-based, first principles analytical approach…arrow_forward- | العنوان In non-continuous dieless drawing process for copper tube as shown in Fig. (1), take the following data: Do-20mm, to=3mm, D=12mm, ti/to=0.6 and v.-15mm/s. Calculate: (1) area reduction RA, (2) drawing velocity v. Knowing that: ti: final thickness V. Fig. (1) ofthrearrow_forward
- A direct extrusion operation produces the cross section shown in Fig. (2) from an aluminum billet whose diameter 160 mm and length - 700 mm. Determine the length of the extruded section at the end of the operation if the die angle -14° 60 X Fig. (2) Note: all dimensions in mm.arrow_forwardFor hot rolling processes, show that the average strain rate can be given as: = (1+5)√RdIn(+1)arrow_forward: +0 usão العنوان on to A vertical true centrifugal casting process is used to produce bushings that are 250 mm long and 200 mm in outside diameter. If the rotational speed during solidification is 500 rev/min, determine the inside radii at the top and bottom of the bushing if R-2R. Take: -9.81 mis ۲/۱ ostrararrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
Physics 33 - Fluid Statics (1 of 10) Pressure in a Fluid; Author: Michel van Biezen;https://www.youtube.com/watch?v=mzjlAla3H1Q;License: Standard YouTube License, CC-BY