You manage a factory that uses many electric motors. The motors create a large inductive load to the electric power line as well as a resistive load. The electric company builds an extra-heavy distribution line to supply you with two components of current: one that is 90° out of phase with the voltage and another that is in phase with the voltage. The electric company charges you an extra fee for "reactive volt-amps" in addition to the amount you pay for the energy you use. You can avoid the extra fee and the need for two components of current by installing a capacitor between the power line and your factory. But, you need to convince the owners of the factory to spend the funds to purchase and install this capacitor. You decide to make a present ion to the owners, using a simple RL circuit as a demonstration device. In your demonstration circuit, you represent the power company with a 120 V (rms), 60.0 Hz source. This source is in series with a series combination of a 21.0 mH inductor and a 16.0 Q resistor. This combination represents the inductive and resistive loads for your factory. (a) To impress the owners, you calculate for them the power factor for the circuit and show that it is not equal to 1. power factor = (b) You then determine the capacitance (in µF) of a capacitor that will bring the power factor to 1. uF (c) Demonstrate to the owners the percentage of increased power delivered to the factory. Pnew Pold x 100% = % Pold

You manage a factory that uses many electric motors. The motors create a large inductive load to the electric power line as well as a resistive load. The electric company builds an extra-heavy distribution line to supply you with two components of current: one that is 90° out of phase with the voltage and another that is in phase with the voltage. The electric company charges you an extra fee for "reactive volt-amps" in addition to the amount you pay for the energy you use. You can avoid the extra fee and the need for two components of current by installing a capacitor between the power line and your factory. But, you need to convince the owners of the factory to spend the funds to purchase and install this capacitor. You decide to make a present ion to the owners, using a simple RL circuit as a demonstration device. In your demonstration circuit, you represent the power company with a 120 V (rms), 60.0 Hz source. This source is in series with a series combination of a 21.0 mH inductor and a 16.0 Q resistor. This combination represents the inductive and resistive loads for your factory. (a) To impress the owners, you calculate for them the power factor for the circuit and show that it is not equal to 1. power factor = (b) You then determine the capacitance (in µF) of a capacitor that will bring the power factor to 1. uF (c) Demonstrate to the owners the percentage of increased power delivered to the factory. Pnew Pold x 100% = % Pold

Similar questions

An electric power station that operates at 15 kV and uses a 20:1 step-up ideal transformer is producing 370 MW (Mega-Watt) of power that is to be sent to a big city which is located 240 km away with only 2.5% loss. Each of the two wires are made of copper (resistivity = 1.68×10−81.68×10−8 Ω.m). What is the diameter of the wires?
A 1.13-mF capacitor is connected to a North American electrical outlet (AVms = 120 V, f = 60.0 Hz). Assuming the energy stored in the capacitor is zero at t = 0, determine the magnitude of the current in the wires at t = S. 174 x Your response differs from the correct answer by more than 10%. Double check your calculations. Al Need Help? Read It Submit Answer
Please asap
Most household power in North America is 120? alternating current (VAC). However, some high-power appliances such as electric ranges and clothes dryers typically require a special 220?circuit. In this problem, you will calculate the energy, power, and current required by a dryer. You will also compare different methods of storing the energy required to run this appliance in a typical drying cycle. Consider a dryer that operates on 220?electricity, and it consumes an average power of 3000?. For this homework, the “Alternating Current” part of the story is irrelevant, so please use our ordinary DC equations (Perhaps this dryer has been specially made for physics experiments so it has a second input that allows it to operate on DC voltage as well!) A cubic meter of “natural gas” (mostly methane) at atmospheric pressure contains about40?? of usable energy. How much natural gas (in m3) would it take to power the dryer for 30minutes? Do some googling, and make an estimate (that means getting…
There is a current of 0.25 A in the circuit of Figure P23.69.a. What is the direction of the current? Explain.b. What is the value of the resistance R?c. What is the power dissipated by R?d. Make a graph of potential versus position, starting from V = 0 V in the lower left corner and proceeding clockwise.See Figure P23.9 for an example.
A 1·21-MF Capacitor is connected to a North American electrical outlet. (AVrms = 120V₁ f = 60.0Hz). Assuming the energy stored in the Capacitor is Zero at + = 0, determine the magnitude & the current in the wires at t = 192 Note: Answer must be in A. S.
In the circuit of the figure suppose that E = 9.00V, R = 15.0 ? and L = 0.060H. At t = 0, switch S1 is closed. What is the initial current through the resistor just after switch S1 is closed? 0 A 0.600 A 150 A Infinite What is the initial rate of change of the current in the circuit just after switch S1 is closed? 0 A/s 150 A/s 0.600 A/s Infinite
The figure below shows a simplified model of a cardiac defibrillator, a device used to resuscitate patients in ventricular fibrillation. R C Riorso + When the switch S is toggled to the left, the capacitor C charges through the resistor R. When the switch is toggled to the right, the capacitor discharges current through the patient's torso, modeled as the resistor Rorso allowing the heart's normal rhythm to be reestablished. HINT (a) If the capacitor is initially uncharged with C = 8.25 µF and E = 1270 V, find the value of R (in ohms) required to charge the capacitor to a voltage of 795 V in 1.20 s. 3.904*10**-6 (b) If the capacitor is then discharged across the patient's torso with Rorso = 1240 0, calculate the voltage (in V) across the capacitor after 4.50 ms. 512.06 V