You are given an S-hydrograph of intensity 0.5 cm/h. How will you use it to develop the 3-hour UH (1 unit = 1cm)? Lag the two S-hydrographs by 3 hours and then multiply the difference by 2/3 Lag the two S-hydrographs by 3 hours and then find the difference. Lag the two S-hydrographs by 3 hours and then multiply the difference by 3/2 Add two S-hydrographs to get an intensity of 1 cm/h. then multiply the resulting sum by 3;

You are given an S-hydrograph of intensity 0.5 cm/h. How will you use it to develop the 3-hour UH (1 unit = 1cm)? Lag the two S-hydrographs by 3 hours and then multiply the difference by 2/3 Lag the two S-hydrographs by 3 hours and then find the difference. Lag the two S-hydrographs by 3 hours and then multiply the difference by 3/2 Add two S-hydrographs to get an intensity of 1 cm/h. then multiply the resulting sum by 3;

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem # 9. A manometer exploration vehicle submerges to a depth of 1000 ft. If the atmospheric pressure at the surface is 1 atm, the water density is 62.4??/??3and ?=32.2??/?2. Determine the pressure on the vehicle in atm.
A discharge of 150 litres per second is to be measured by a V-notch of vertex angle 60°. What would be the head over the vertex ? If the accuracy of the reading of the head is 1 mm, what error in discharge can be expected at this level? Assume C, = 0.62.
The equation k(dQI dt) + Q(t) = I (t) has been used to describe the gradual depletion of flow in a river during a rainless period. In this case, 1(t) = 0 and Q(1) = Qo for t = 0. Solve the differential equation for Q(t) for t>0 and plot the result over a 20-day period if k = 10 days and Qo = 100 cfs. %3D %3|
For a sample of water, EC reading was 208 milli-Siemens/cm, what is the value of TDS in PPM and PPB?
You want to measure velocity in a water tunnel. Due to budgetary restrictions, you were unable afford a pitot-static tube, so you decided to inserts a total-head probe and a static-head probe both in the mainstream away from the wall boundary layers. The two probes are connected to a manometer. Write an expression for tunnel velocity V in terms of the parameters in the figure. Is it critical that the first head be measured accurately? And how does part this differ from a Pitot - static tube formula?
2. An iceberg having a specific gravity of 0.92 floats in saltwater having a specific gravity of 1.03. If the volume of ice above the surface is 540cu.m, what volume will be above the surface of fresh water when it is navigated there? 3. A hydrometer consists of 8-mm diameter cylinder of length 20cm attached to a 25-mm diameter weighted sphere. The cylinder has a mass of 1.20-g and the mass of the sphere is 12.80g. At what level from the junction of the cylinder and sphere will this device float in liquids having the following specific gravities. a. 0.80 b. 1.0 c. 1.20 4. A block of wood floats in water with 6 inches projecting above the water surface. If the same block were placed in alcohol with a specific gravity of 0.82, the block would project 4 inches above the surface of the alcohol. Determine the specific gravity of the wood block.
A vertical 150 mm pipe leaves a water tank of surface elevation 24. Between the tank andelevation 12, on the line, 2.4 m of head are lost when 56 Fs flow through the line. If an openpiezometer tube is attached to the pipe at elevation 12, what will be the elevation of the watersurface in this tube?
Q/ Find P,-Po and Also find h in the figure below if Pa-Pa is 11.5 KN/m. Water h=? Oil R.D= 0.8 0-30m 0-15m 0-30m 0.10m 0.08m Carbon tetrachloride R.D = 1.60 Mercury RD 13-55
Two barometers are put at the same location. The specific weight of liquid of the first barometer is γ1 = 10.77 kN/m3, and the specific weight of the second one is γ2 = 11.06 kN/m3. If the liquid height to the freesurface of the first barometer is h1 = 8.26 m, calculate the liquid height of the second barometer, h2_______m
A Venturi meter with a throat of 15 cm is used to measure the flow rate of water along a horizontal pipe that has an internal diameter of 17 cm. The flowmeter is calibrated using a solution of salt with a concentration of 10 gl–1 fed upstream of the meter at a rate of 50millilitres per second. If the pressure difference between the upstream position and the throat is found to be 759 Nm–2 A when a sample of salt-bearing water was analysed downstream from the flowmeter and found to be 15 mgl–1 , determine the flow rate of waterthrough the pipeline and the coefficient of discharge of the flowmeter.
For the system below, EI is constant. If x = 9.48 m from point A, determine the value of EI(Δ) ? If x = 2.80 m from point A, determine the value of EI(θ) ? If x = 8.32 m from point A, determine the value of EI(Δ) ? If x = 6.13 m from point A, determine the value of EI(θ) ?
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. *12.9517*99.9358*30.4889*39.5136 What gage pressure p1 in kPa, is needed to provide the given flow rate? *1121 kPa*1692 kPa*1328 kPa*1725 kPa Please answer with complete and detailed solutions. thank you. ASAP