Write the required code that converts packed BCD number Pack BCD (29H) to ASCII number. Store the result in registers R4:R3 Given five inputs (a, b, c, d, e) connected to 8051's port P and P, with : P10 = a, P30 = b, P13 = c, P33 = det P14 = e. Outputs So and Sj are connected to P39 and P; 1 respectively as shown in the figure below. We propose to realize the following logic functions. So = abt cd+ e.(ab+ab) Si = G5+d+gak 1. Using 8051 boolean instructions, write subroutines for So and S1. 2. Based on the given flowchart, write the main program for the polling of port P.

Q: A 4-bit carry-look ahead adder (CLA) is used to add the two numbers: (A3A2A¡Ao) = 0110 and B…

A: Given Data : A3A2A1A0 = 0110 B3B2B1B0 = 1001 C0 = 1 Equation : Si = Pi ⊕ Ci Ci+1 = Gi + PiCi Gi =…

Q: Problem_#03] The input waveform below is applied to a two bit full-adder. Determine the output…

A: i can answer only one question only  question 4 post seperately SOLUTION

Q: Write an ALP in 8085 to obtain 10's complement of BCD number Xi where i=0 to 99 . The string of…

A: 1. Initialize pointers to source (STRING) and destination (RESULT) locations.2. Load the first BCD…

Q: Question I have 2 and a half breadboards, and some specific IC's, I need to implement a 4 bit binary…

A: I have 2 and half breadboards,and some specific IC's,i need to implement a 4-bit binary full…

Q: To implement a 1-bit adder, write a Boolean expression for the Sum function. Sum(A, B, C) = Input:…

A: In this question we need to write the Boolean expression for the Sum function while implementing the…

Q: Perform the multiplication of the 4-bit number 1011 (multiplicand) with 1001 (multiplier) using the…

A: Perform the multiplication of the 4-bit number 1011 (multiplicand) with 1001 (multiplier) using the…

Q: you need to design and draw a 3-bit synchronous binary up/down counter for experiment 5. You need to…

A: Given that, Add a bit named "M" for the excitation table that helps it switch between up and down…

Q: Consider the circuit shown below. Notice that it utilizes dataflow Verilog operators that you are…

A: As per the given code, each assign statement that uses addition or subtraction operator will produce…

Q: Subject-Microprocessor Write an ALP in 8085 to convert two digit BCD number into Excess-3 code. (BCD…

A: Below is an example of an 8085 assembly language program to convert a two-digit BCD number stored in…

Q: Implement the following RTL code using n-bit parallel adder and registers a: X+X+Y a': X+X+Y' +1

A: Step 1 The answer is given in the below step

Q: olve and implement using logism Design a 4 bit binary counter using T Flip flops, a 4 bit binary…

A:

Q: you need to design and draw a 3-bit synchronous binary up/down counter for experiment 5. You need to…

A: According to the information given:- We have to design and draw a 3-bit synchronous binary up/down…

Q: Convert in machine code for MIPS LW 55, 33(S2); Add R1, T3, S5;

A:

Q: Homework Write VHDL to generate an N bit adder from a full adder. N should be defined as generic.…

A: Below is the code for n-bit adder from full Adder. I have defined n as generic here and set its…

Q: Let X be number of gates in an 8-bit adder (i.e., adds two 8-bit numbers) and Y be the number of…

A: The above question is solved in step 2 :-

Q: Modify the VHDL code in Figure 7.52 by adding a parameter that sets the number of flip-flops in the…

A: Basically,VHDL is a hardware description language that contains the features of conventional…

Q: Using the attached full adder as a component, write a VHDL code for a an adder that adds two 2-bit…

A: Answer :   FUL ADDER SUB MODULE :