Write the given data. Type of bolt=SAE grade 2F=20000 lbn= 50=0.750proof Calculate the load on each bolt. Feach=20000n=200005-4000 lb Write the stress developed on each bolt. o=0.750proof=0.7555×103 psi=41250 p si Calculate the diameter of the bolt. O=FeachA41250=4000π4d2d=0.351 in= 38 inIn case of UNC nad UNF,UNC=16U NF=22so,d=38-16 UNC Therefore, option (a) is correct.

Write the given data. Type of bolt=SAE grade 2F=20000 lbn= 50=0.750proof Calculate the load on each bolt. Feach=20000n=200005-4000 lb Write the stress developed on each bolt. o=0.750proof=0.7555×103 psi=41250 p si Calculate the diameter of the bolt. O=FeachA41250=4000π4d2d=0.351 in= 38 inIn case of UNC nad UNF,UNC=16U NF=22so,d=38-16 UNC Therefore, option (a) is correct.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.31P

See similar textbooks

Similar questions

Statement: The figure below shows three cycles of time-varying loading on a double D-ring held together with a single bolt and nut. The figure shows both the bolt tensile force and the member compressive force. QUESTION 1 - Based on the figure, give the minimum and the maximum of the external load, P?
Hand written plz
Hand written plz asap please...... I'll rate plz asap plzzzzzzz
Need only a handwritten solution only (not a typed one).
mechanical design
A leafs spring contains 4 full-length and 8 graduated leafs. The eyebolts at the support are 20 inches apart and the system should carry a load of 400 lbs. If the thickness of the available bronze plate is 1“ and Sy = 80 ksi, what leaf width is required at FOS = 8?
Kindly answer correctly. Please show all the necessary steps. Thanks in advance
Machine Elements
S-3) In order to carry the 100 KN force safely on the frame in Figure 3, find the diameters of the B and D pins (B single cut D double cut), the thickness t of the BD bar. (Safety Cat.(S)=2, T = 250 Nmm2 o -350 N/mm2) 40.a mm 300 mm ТАКE a-9,6 60.a mm 50 mm D Yatağı 100 mm C t mm |F=100 kN
In the attached picture, you'll see a red circle around a particular triangular feature. What is this feature called?
Question 1: A race car is turning (cornering) on a flat road, as shown in Figure Q1-1. The speed of the car is 300 kph and the turning radius is 260 m. Having the car parameters as below, answer questions a) and b). ● . ● ● m = 890 (kg) (57% of the weight is on the rear axle); Air density = 1.225 (kg/m3); Equivalent aerodynamic lift coefficient for front axle= -0.915 (-); Aerodynamic frontal area= 1.11 (m²); Slip angle of the front tyres= +2.4 (°); Slip angle of rear tyres= +1.2 (°); The steering angle of wheels= -1.9 (°); The efficiency of the drivetrain from the engine to the contact patch of tyres is 100%. 8=-1.9°- ---R=260 m α = +2.4° αR = +1.2° Figure Q1-1 Motion of the vehicle and the angles a) Calculate the engine power delivered to tyres to overcome the total induced drag due to lateral force.
I need answer in 10 minutes please quickly