Answered: Write an assembly code that will…

Write an assembly code that will calculate the value of y in the following equation: y= 2a+ 3b−4c Here, roll= 2019000510221 Microprocessor and Interfacing, Electrical and electronics engineering.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Related questions

Q: Write a MARIE assembly code to perform the following pseudocode excerpt. Input a number Assign this…

A: MARIE (Machine Architecture that is Really Intuitive and Easy) stands out as a simplified…

Q: Convert the high-level code into assembly code if ( i == j || i == k ) i++ ; // if-body else…

A: Assembly Language: An assembly language is a type of low-level programming language made…

Q: Several data sources are used for the various instructions in this classification. a(n): A Several…

A: Multiple Instruction Many Data is the appropriate response. Explanation: many data sets and…

Q: In the Allen-Bradley MOV instruction, constants such as 250, 400, 5.5, etc., can be entered into the…

A: The answer is False.

Q: a. movq (%rdi), %rax movq (%rax), %rax movq (%rax), %rax movq (%rax), %rax addq %rcx, %rax

A: Welcome to the fascinating world of assembly language, where every instruction is a testament to the…

Q: Instruction Type R-Format I-Format D-Format B-Format Percentage of Instructions # of Cycles 50% 20%…

A: Cycles Per Instruction (CPI) is a metric used in computer architecture to measure the average number…

Q: Convert the following program to assembly - using the Assembly syntax. In the table below, enter the…

A: We need to convert the given program to assembly - using the Assembly syntax.

Q: Question 1. Convert the following code into assembly language program while (BX <- X) BX = BX + 2; X…

A: The question is on convert the code in assembly language.

Q: Draw block diagram for 64k * 8 memory

A: Memory is an electronic device used to store data or programs on a temporary or permanent basis. The…

Q: =: MARIE Assembly Language (Simulator)

A: MARIE: a Machine Architecture that is Really Intuitive and Easy, is a simplearchitecture consisting…

Q: One-way programmable read-only memory, or PROM, is a specific kind of computer memory that cannot be…

A: Introduction PROM: PROM, or programmable read-only memory, is a type of computer memory that can be…

Question

Write an assembly code that will calculate the value of y in the following equation:

y= 2a+ 3b−4c

Here, roll= 2019000510221

Microprocessor and Interfacing, Electrical and electronics engineering.

Write an assembly code that will calculate the value of y in the following equation
y = 2a + 3b – 4c
Here,
a is first and second digit of your roll number
b is third and fourth digit of your roll number
c is the last two digits of your roll number.
All the numbers should be considered in decimal format.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

A program consists of 100,000 instructions as follows: Type of Instruction, IC, and CPI Instruction Type Integer arithmetic Data transfer Control transfer Floating-point arithmetic 12,000 Processor Instruction Count Cycles per Instruction M1 - 500 MHz 48,000 M2 850 MHz 32,000 8,000 Determine the program execution time, the effective CPI for the machine, and the MIPS rate for the following processors. (each box is 2 points except CPI) 3 to 5 decimal places) 6 to 5 decimal places) 11 4 Execution Time Type of instruction, IC, and CPI CPI seconds (round seconds (round to 2 decimal places) (round with round up) with round up) MIPS rate (Whole number only (Whole number only
Translate the following C statement sequence into MIPS assembly instructions (x is an integer):
ASSEMBLY The ROR instruction is only suitable for signed integers. True False
Please do parphsing for these parpharphs please because it is 69% palagrisim percentage, see the parpharphs below . 1)Data bus : It is a group of conducting wires which carries Data only. Data moving in and out of the data bus is bi-directional, since the processor reads and writes data .When it is write operation, the processor will put the data (to be written) on the data bus, when it is read operation, the memory controller will get the data from specific memory block and put it into the data bus. The width of the data bus reflects the maximum amount of data that can be processed and delivered at one time.A 64-bit processor has a 64-bit data bus and can communicate 64-bits of data at a time ◆◆Address bus and control bus are◆◆ uni-directional 2)Address bus : It is a group of conducting wires which carries address only. Address bus is unidirectional because data flow in one direction, from microprocessor to memory or from microprocessor to Input/output devices. 3)Control bus :…
Subject name: Microcomputer Principle Application Determine the data in AL after the following sequence of instructions. Assume (DS) = 20H. MOV AL, 25H MOV BX, 0061H AND AL, 21H[BX]
Write LMC assembly code that prints the minimum of two numbers
Computer architecture Please not expert using Ai answer can you use letter and pen design the circuit Q1)= (Draw the circuit of a 1-bit register that can perform the x+y.z: R. € I. microprocess and retains the value in other cases. Note: R, represents 1-bit of the register and I, represents a 1-bit input.) Please use when designing the register Like two and gates and one or gate and D flip flop and that performs x+yz operation
For each of the following lines of assembly language, determine the appropriate instruction suffix based on the operands. (For example, mov can be rewritten as movb, movw, movl, or movq.) Drag the appropriate labels to their respective targets.
THIS IS MY CODE SO FAR: // header #include <stdio.h> // define the IM and DM size #define IM_SIZE 250 #define DM_SIZE 10 // Define the ISA of the Tiny Machine Architecture #define LOAD 1 #define ADD 2 #define STORE 3 #define SUB 4 #define IN 5 #define OUT 6 #define END 7 #define JMP 8 #define SKIPZ 9 // Accurately represented architecture int PC = 0; // PC = Program Counter int IR; // IR = Instruction Register int MAR1, MAR2; // MAR1,MAR2 = Memory Address Registers 1 and 2 int MDR1, MDR2; // MDR1,MDR2 = Memory Data Registers 1 and 2 int A = 0; // A = Accumulator int IM[IM_SIZE]; // IM = Instruction Memory int DM[DM_SIZE]; // DM = Data Memory // opening the file void openProgram(const char* filename) { FILE* file = fopen(filename, "r"); if (file == NULL) { printf("Error opening file.\n"); return; } int opcode, address; int i = 0; while (fscanf(file, "%d %d", &opcode, &address) == 2 && i < IM_SIZE) {…
It has to be ASSEMBLY CODE (like MOV AL, 10)