Convert the following program to assembly - using the Assembly syntax. In the table below, enter the syntax in this format: LDI R19, 24 Instruction Load 5 into register 16 Load 10 into register 17 Load 32 into register 18 Load 2 into register 19 Add register 16 to register 17 Subtract register 19 from register 18 Multiply register 16 by register 19 Divide register 17 by 2 (logical shift) Compare register 16 with register 17 Branch to top if R16 and R17 are equal Assembly Syntax

Convert the following program to assembly - using the Assembly syntax. In the table below, enter the syntax in this format: LDI R19, 24 Instruction Load 5 into register 16 Load 10 into register 17 Load 32 into register 18 Load 2 into register 19 Add register 16 to register 17 Subtract register 19 from register 18 Multiply register 16 by register 19 Divide register 17 by 2 (logical shift) Compare register 16 with register 17 Branch to top if R16 and R17 are equal Assembly Syntax

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Question 4 Provide a code segment, in any Assembly language you choose, that implements the following C++ statement, X = Y + 3. Do not write a full program, just the lines of code, including data declarations if necessary. You may assume that all registers have been cleared prior to your code statements. Please keep it simple.
4. Write an instruction sequence that generates a byte-size integer in the memory location defined as RESULT. The value of the integer is to be calculated from the logic equation (RESULT) = (AL) · (NUM1) + (NUM2) · (AL) + (BL) Assume that all parameters are byte sized. NUM1, NUM2, and RESULT are the offset addresses of memory locations in the current data segment.
Assume that the variables in the following C code are integers that are stored in the following registers: $te = c, $se = x, $s1 = y, $s2 = z Convert the following C code to MIPS instructions. switch (c) { case 1: x = y + z; break; case 2: x - y - z; break; default: x++; break; }
Write an assembly program using MARIE that will do the following: Given three numbers (X, Y, and Z), find the product of X and Y (called PROD for reference)Using this product as a dividend, find the quotient and remainder when divided by Z as thedivisor. Use the values:X = 5, Y = 3, and Z = 4 For the multiplication and division use repetitive addition or subtraction respectively.
Please solve and show all work. For the following C statement, what is the corresponding MIPS assembly code? Assume that the variables f, g, h, i, and j are assigned to registers $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. Assume that the elements of the arrays A and B are 8-byte words: f = (g+i+2) + (h − 8); B[8] = A[i-9] + A[j+8] + 7;
A simple two-pass assembler does the following in the first pass: A. It allocates space for the literals. B. It computes the total length of the program. C. It builds the symbol table for the symbols and their values. D. It generates code for all the load and store register instructions. E. None of the above.
Convert the given hex value to its R-format MIPS instruction by completing the following table. The instruction and letters for registers must be in lower case. DO NOT TYPE DOLLAR SIGNS WITH REGISTERS. Hex Opcode (decimal) rs (decimal) rt (decimal) rd (decimal) funct (decimal) Instruction 02488822 O 18 16 17 34 sub s4 $$1 " $ to " LA
For the RISC-V assembly instructions below, what is the corresponding C statement? Assume that the variables f, g, h, i, and j are assigned to registers x5, x6, x7, x28, and x29, respectively. Assume that the base address of the arrays A and B are in registers x10 and x11, respectively. sub x30, x28, x29 slli x30, x30, 2 add x3, x30, x10 add x4, x30, x11 1w x30, 0 (x3) 1w x31, 0 (x4) add x30, x30, x31 sw x30, 16 (x11)
3. For each instruction in the table, write 8 hexadecimal digits that represent the 32 bits in the destination register after the instruction is executed. Assume s0 is 0x98AB3C6A, s1 is 0x20503666. Instructions to, 50, s1 t1, so, s1 t2, so, s1 t3, 50, 51 addi t4, 50, 0x210 wwwwwww andi t5, 50, -16 add and or xor slli t6, 50, 12 srai s2, 50, 8 Dest. reg. in 8 hexadecimal digits
1) For each of the instructions below, assume the initial conditions shown for r3-r5 and the flags. For each instruction, show the value of any registers that are changed. If the instruction affects flags, show the value for all flags that are affected. Initial conditions: r3 = 0XF0E1 D2B3 r4 = 0x1496 3A40 r5 = 0×47CE 811E NZCV = 1010 a) ADCS r4,r3,r4 b) CMP r3,r5 c) TST r4,#0xF d) MVNS r5,r3 e) ASRS r3, r3, #1
pls help me to convert this c code to ARM assembly code (using branch) int main(){int i;int sum =0; // assume sum is a memory variablefor (int i=0; i<8; i++){if (i<4)sum = sum + 2*i;elsesum = sum + 3*i;}}
Write the MIPS instructions for the following problems using arithmetic and shift instructions. Using a shift operation, write MIPS code that multiplies the number in $t0=16 by 16.