Why does the viscosity of a gas generally decrease with decreasing temperature whereas for a liquid its viscosity generally increases? Calculate and plot using Matlab the variation in the coefficient of dynamic viscosity of air in USC units from 35•F to 120•F. Sutherland's Law can be expressed as 1.5 T To+S µ= µ0 То To T+S

Why does the viscosity of a gas generally decrease with decreasing temperature whereas for a liquid its viscosity generally increases? Calculate and plot using Matlab the variation in the coefficient of dynamic viscosity of air in USC units from 35•F to 120•F. Sutherland's Law can be expressed as 1.5 T To+S µ= µ0 То To T+S

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Mechanical EngineeringFluid Mechanics
! Required information The dynamic viscosity of air at 20°C is u≈ 1.80E-5 Pa-s. Estimate the viscosity of air at various temperatures by the below mentioned methods. Determine the viscosity of air at 500°C by the Law of Corresponding States. E-5 kg/(m.s)
A bullet is to be tested in the laboratory to determine the drag force on it. Dependent parameter the drag force D (Newton) depends on the velocity of the bullet V(m/s), the length of the bullet L(m), sound velocity c(m/s), density of fluid ρ (kg/m3) and dynamic viscosity µ(kg/ms). Solve the problem by making the necessary assumptions and drawing the schematic figure. I-Determine the nondimensional p parameters using repeating variables ii-a bullet with a speed of 96,2 m/s in air may be modelled in a water tunnel with a test section velocity of 262 cm/s. Determine the length of the model, if the length of the bullet is 56,2 mm. The air and water temperature is 20 oC degree at 1 atm. iii- if the drag force on the model is measured to be 2,62 N, then determine the expected drag force on the bullet. Comment on dynamic similarity equivalence?
Please include each and every expression/formulas
Please solve in simplest terms
> | E9 docs.google.com/form تبديل الحساب Questions 7 نقاط Q1/ The power of 6-blade flat blade turbine agitator in a tank is a function of diameter of impeller, number of rotations of the impeller per unit time, viscosity and density of liquid. From a dimensional analysis, obtain a relation between the power and the four variables. 3. صفحة 2 من
When a fluid flows over a surface, the shear stresS I (N/m) at the surface is given by the expression du dy surface where u is the viscosity (N-s/m), u is the velocity parallel to the surface (m/s), and y is the distance normal to the surface (cm). Measurements of the velocity of an air stream flowing above a surface are made with an LDV (laser-Doppler-Velocimeter). The values given below were obtained. y u y и 0.0 0.00 2.0 88.89 1.0 55.56 3.0 100.00 At the local temperature, u = 0.00024 N-s/m. In four decimal places, calculate du/dy at the surface using all the points.
Fluid Statics Please provide a complete and readable solution for the problem if necessary and an explanation. Thank you!
A new thermometer is invented where the temperature scale is in degree G (°G). The boiling point of water is 900°G and the freezing point of water is 120°G. Derive an equation for conversion from °G to °C.
A ship 350 m long moves in sea water whose density is 1030 kg/m3 . A 1:120 model of this ship is to be tested in a wind tunnel. The velocity of the wind tunnel around the model is 35 m/s and the resistance of the model is 65 N. Determine the velocity and also the resistance of the ship in sea water. The density of air is given as 1.24 kg/m3 . Take the kinematic viscosity of air and sea water as 0.012 stokes and 0.018 stokes respectively.
The pressure drops 4P = P₁ P2 through a long section of round pipe can be written in terms of the shear stress Tw along the wall. Shown in Figure 3 is the shear stress acting by the wall on the fluid. The shaded region is a control volume composed of the fluid in the pipe between axial locations 1 and 2. Using the method of repeating variables, generate a relationship for pressure drop as a function of all other parameters Final ans AP = P μ (₁ AP= {(₂17₂) P₁ CV UPL м = (²1 ²² an! VPL O P.H. L V
1. To determine the dynamic viscosity of a liquid you take repeated measurements of the liquid density and kinematic viscosity. These data are summarized in the following table: Avg. measurement Total Uncertainty P 999 kg/m³ ±0.5% V 1.23 mm²/s ±0.01 mm²/s kg Ns What is the dynamic viscosity? Give dynamic viscosity in units of; which is the same as ms 2. Determine the absolute and relative uncertainties in the dynamic viscosity.