A constant volume gas thermometer is used to determine the temperature of an unknownfluid. Pressure data for thermometer in the unknown bath (P) and a Triple Point Cell (P)are given below.P[Torr]100.0P [Torr]127.9200.0256.5300.0385.8400.0516.0What is the temperature of the unknown fluid bath?explain and show all work please and writeclearly

A constant volume gas thermometer is typically made up of a bulb filled with a predetermined amount…

A constant volume gas thermometer is used to determine the temperature of an unknown fluid. Pressure data for thermometer in the unknown bath (P) and a Triple Point Cell (P) are given below. P [Tor] 100.0 P [Torr] 127.9 200.0 256.5 300.0 385.8 400.0 516.0 What is the temperature of the unknown fluid bath?

A constant volume gas thermometer is used to determine the temperature of an unknown fluid. Pressure data for thermometer in the unknown bath (P) and a Triple Point Cell (P) are given below. P [Tor] 100.0 P [Torr] 127.9 200.0 256.5 300.0 385.8 400.0 516.0 What is the temperature of the unknown fluid bath?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 7 A model tow-tank test is conducted on a bare hull model at the model design speed in calm water. Determine the effective horsepower (hp) for the ship, including appendage and air resistances. The following parameters apply to the ship and model: Ship 1,100 Model Length (ft) Hull Wetted Surface Area (ft2) Speed (knots) 30 250,000 15 Freshwater Water Seawater 50°F 70°F Projected Transverse Area (ft²) Cair 7,500 0.875 Appendage Resistance (% of bare hull) 10% Hull Resistance (Ibf) 20
Given the following Atmospheric Data: Altitude (m) Pressure (kPa)0 - 101.331000 - 89.872000 - 79.503000 - 70.114000 - 61.66 Use linear interpolation to estimate the atmospheric pressure at: Altitude (m) Pressure (kPa)4MM ?2689 ?3500 ? (where MM is your birth month, so if you were born in December, evaluate at 312 meters)
Please provide Screenshot of the table ,If possible.
4. Referring to the property table below for saturated liquid, using linear interpolation to determine the following values: a. Pat T = 94°C b. U at P = 0.4285 bar C. vat U= 315.67 kJ/kg Internal Energy, Specific Volume, v x 10 (m*/kg) U ("C) (bar) (kJ/kg) 0.3858 1.0259 313.90 75 80 0.4739 1.0291 334.86 85 0.5783 1.0325 355.84 90 0.7014 1.0360 376.85 95 0.8455 1.0397 397.88 100 1.014 1.0435 418.94
i need the answer quickly
• Temperature plot scoped to steam pipe (cast iron) in C° units. Fill in the below table. Compute the temperature drop up to THREE decimal places (see hint given below). Temp drop in Insulator Temp drop in Pipe ANSYS Results • Include the above table in your submission.
1. To determine the dynamic viscosity of a liquid you take repeated measurements of the liquid density and kinematic viscosity. These data are summarized in the following table: Avg. measurement Total Uncertainty P 999 kg/m³ ±0.5% V 1.23 mm²/s ±0.01 mm²/s kg Ns What is the dynamic viscosity? Give dynamic viscosity in units of; which is the same as ms 2. Determine the absolute and relative uncertainties in the dynamic viscosity.
Q1. Honey is a very widely used ingredient in cooking all around the world. Many commercial honey manufacturers heat treat honey to remove harmful bacteria that may be present. The density and viscosity of the honey varies with temperature, as shown in table 1. Temperature K 293 298 303 308 313 318 323 Density kg/m³ 1403 1398 1393 1388 1383 1378 1373 Viscosity Pas 55.66 46.45 37.99 30.28 23.32 17.11 11.65 Table 1: Fluid properties of honey. A particular processing facility heats and sterilises 500 kg of unprocessed honey every 30 minutes. The unpro- cessed honey is stored in large vats, then pumped though pipes into heating units before being pumped through another pipe to be bottled. The pipe carrying the honey from a storage container, which is 11 m tall, to a heating unit is 5 m long and has a diameter of 10 cm. Prior to being heated the honey is kept at 25°C. (a) What is the pressure difference between the top and bottom of a storage vat when it is full? (b) What is the volume flow…
Can you help with both please.
plz ansswer q1 part e velocity is in km/h not in m/s