Which of the following is normally used for very large discharge flow measurements? (my answer was C) a. Orifice b. Nozzle c. Venturimeter d. Pilot tube 2. Which of the following is used to increase flow velocity from a pipe? (my answer was A) a. Nozzle b. Pilot tube c. Venturimeter d. Orifice 3. A garden hose with diamater of 2cm has a flow velocity of 2 m/s. The end nozzle must have a velocity 4 times the velocity at the hose. Determine the nozzle size in terms

Q: An illegal connection was detected along a water 400 mm water supply line made with cast iron pipe…

A:

Q: PROBLEM: A dry soil is mixed with 17% by mass with water and compacted. The volume of wet soil is…

A:

Q: i) A system for an ordinary toilet tank filling is shown in figure below. The ball floats on the…

A: The block diagram for the system as below,

Q: Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on…

A:

Q: Urgent Hello please answer this problem as soon as possible. Topic is 'Fluid flow measurement' in…

A: Given data- Diameter of orifice d1 =75 mm = 0.075 mOrifice discharge Q = 23.41…

Q: Which of the following best describes a Venturi Meter? an opening having a closed O perimeter in a…

A: Venturimeter are Flow Measurement Instruments Which uses a converging section of pipe where we apply…

Q: (c) Venturi-type flowmeter shown in Figure 5 is used to obtain the flowrate of oil inside a conduit.…

A: ## solution of venturi type flow meter, and calculation of volume flow rate, mass flow rate,

Q: A water sample contains 6.35 mg/L of calcium (Ca), 7.3 mg/L of magnesium (Mg) and sodium (Na) of 21…

A: Gram equivalent=weight/(equivalent wt/ =7.3/(24/2)  =0.608meq/L

Q: Determine the moment of inertia of the cross-sectional area about the z axis. Set a = 120 mm, b= 110…

A: Given Diagram:                     To Find:moment of inertia of the cross-sectional area about the…

Q: Water flows into the Tee at Ve 14 m/s (Figure 1) gure <1 of 1 17 3m Part A Determine the velocity of…

A: The velocity at the inlet at point C, Vc= 14 m/secThe diameter of the jet at C = 50mmThe diameter of…

Q: (c) Which of the following would be considered control volume system? a Tire b. Piston-cylinder…

A: Which of the following would be considered control volume system? e. Mixture of liquid water and air…

Q: If a triangle of height d and base b is vertical and submerged in liquid with its vertex at a…

A:

Q: Urgent, need correct answer as soon as possible with complete solution. Box final answer in 4…

A: Diameter=10mm

Q: Solve and Draw the figure completely labelled with all the notations used in your solution. A 100…

A:

Q: Using the information below, select the correct answers below: CiAna 360 C = 0.60 A (ha) = 70 Time…

A: C=0.6A=70 haLength of travel=8000 mElevation difference= 25mh=1mTo find- Discharge

Q: The height of the fluid inside the tube after immersion is 1⁄8 the height of the cylinder glass…

A:

Q: A 2-foot diameter pipe carries stormwater discharge from a site. The concrete pipe was designed with…

A:

Q: Find the total loss of head between A and F. in m

A:

Q: In testing a fire pump, it is desired to flow 500 gpm (1890 liters per minute) from a 1 3/4-inch (45…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: A 60 mm diameter pipe as shown contains glycerin with a density of 1258 kg/cu.m at 8.5 cu.m/hr. a.…

A: Given, Diameter of the pipe (d) = 60 mm Density of glycerin (ρgly.) = 1258 kg/m3 Flow rate (Q) = 8.5…

Q: The flow of water in a pipe of about 3 meters in diameter can be measured by a. venturimeter b.…

A: Venturimeter:- Venturimetre is a device used for measuring the rate of flow of fluid flowing through…

Q: Given in the table are points in a pipe with some notes: B C F Pressure (kPa) 100 140 140 110 120…

A: According to Bernoulli theorem : Total head= Pressure head +Velocity head +Datum head    Pressure…

Q: Suppose that a = 3.24 m and b = 1.8 m. (Figure 1) Figure y=x¹/2 b 1 of 1 > X Part A Determine the…

A:

Q: Determine the displacement at point D (in the middle of section A) of the overhang white spruce…

A:

Q: Research atleast 4 venturi meter write the problem and solution legibly draw also the diagram if…

A: question -- Figure shows schematic of a venturi meter. The cross sectional area is 100 mm^2 at A and…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.