i) A system for an ordinary toilet tank filling is shown in figure below. The ball floats on the water. As the ball gets closer to the top of the container, the stopper decreases the flow of water. When the container becomes full, the stopper shuts off the flow water. Draw a block diagram for the system described above with clear label of each components. Pulleys Cord Stopper Water Ball Fleat Container Stepeock Water

i) A system for an ordinary toilet tank filling is shown in figure below. The ball floats on the water. As the ball gets closer to the top of the container, the stopper decreases the flow of water. When the container becomes full, the stopper shuts off the flow water. Draw a block diagram for the system described above with clear label of each components. Pulleys Cord Stopper Water Ball Fleat Container Stepeock Water

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 40 psi, determine the gage pressure of the gasoline line. Assume the unit weight of air to be 0.0765 lb/ft3. pls answer asap thank you
A pressure gauge at elevation 12m at the side of an open tank containing a liquid reads 80 kPa. Another gauge at elevation 7m reads 120 kPa. What is the elevation of the liquid surface? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: /Zero
Please only provide the correct answer choices for the following:
Referring to the figure shown below, water contained in a piston-cylinder assembly, initially at 1.5 bar and a quality of 40%, is heated at constant pressure until the piston hits the stops. Heating then continues until the water is saturated vapor. The initial height, L1, is 0.05 m and the change in height, L2, is 0.03 m. Patm-1 bar Piston Water P₁ = 1.5 bar L₁ For the overall process of the water, evaluate the work and heat transfer, each in kJ/kg. Kinetic and potential effects are negligible.
A cylindrical steam boiler is to have a volume of 1340 cu ft. The cost of the metal sheets to make boiler should be a minimum. What is the required base diameter in feet? 11.95 12.31 13.64 18.46
Two steel balls are made to freel fall through two similar containers with one filled with water and other filled with oil. Determine in which container will the ball hit the bottom first. Give reason to support your answer. (Hint: water and oil have different viscosity)
2- Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on the pressure gage is P kPa, determine the distance between the two fluid levels of the manometer if the fluid is (a) mercury (p = 13,600 kg/m³) or (b) oil (p = 850 kg/m³). First names starting with A to L First names with M to Z P (kPa) -15 starting -35 Gas h = ?
Determine the equivalent length of four 90° elbows, two straight-run tees (all wrought), and two gate valves for 1 in diameter copper pipe.
Give the discharge/flow rate in (m3/s) of the system with a constant velocity of 2.5 m/s given the following diameters. 1. d = 1.5 m 2. d = 150 mm note: Please write the final answer in two decimal places. Please write the correct unit Please write legibly It would be better if the solution could be typewritten Thank you
9 PLEASE PROVIDE DETAILED SOLUTION THANKYOU
tiutly futimerged Vertical Plane) Hy drostatic Thrust: Ah キo pgBo td-}) throreticat Dep th of Pressuve: h.HF Trial HI Trial HZ Trial # 3 か0 mg a10 mg l10 mg B 14 cm 1.4 cm I1.4 cm %3D 11.5 cm こし 11.5 cm し 15.5 cm 12.u em D ラ 9.8 cm 22. 8 em 22.8 cm un 8.22 143 cm d= Il.5 cm d 8.0 cm 9.& cm hs 4.5 cm 3.6 cm %3D
4