2- Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on the pressure gage is P kPa, determine the distance between the two fluid levels of the manometer if the fluid is (a) mercury (p = 13,600 kg/m³) or (b) oil (p= 850 kg/m³). First names starting with A to L First names with M to Z P (kPa) -15 starting -35 Gas h = ?

2- Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on the pressure gage is P kPa, determine the distance between the two fluid levels of the manometer if the fluid is (a) mercury (p = 13,600 kg/m³) or (b) oil (p= 850 kg/m³). First names starting with A to L First names with M to Z P (kPa) -15 starting -35 Gas h = ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Example Problem: Venturi meter system. The venturi meter shown in figure blow carries water at 60°C.…

A: P1=PA+γWy+1.18PA-PB=γ0.46-1.18+1.25×γw1.18PA-PBγ=-0.72+1.27×1.18PA-PB9.65=-0.72+1.27×1.18PA-PB9.65=0…

Q: Q3. A sphere is tested for drag resistance in a the wind tunnel. A pressure tapping at the…

A: Given :

Q: A pressure of 10 kPa, gage, is applied to the surface of a liquid with specific gravity of 1.3 in an…

Q: Find the atmospheric pressure when the barometer reading is 800 mmHg. Given the specify gravity of…

Q: ) For the system in figure, the atmospheric pressure is 101.33 kPa and the absolute pressure at the…

Q: Three pipes as per details given are connected in parallel between two points. Diameter Pipe A B C…

Q: Consider the three pipes shown below in cross section. From left to right, they contain water,…

A: Give data,in three pipe cross section contains water, mercury and gasoline respectively.all pipe…

Q: Flow from a tank with falling head. For the tank shown in figure below, find the time required to…

Q: Question 1 5 Marks The air-oil-water system shown below is at 21°C. Gauge A reads 11 kPa and gauge B…

Q: A 300mm by 150mm venturi meter is installed in a vertical pipeline carrying water as shown in the…

A: Our objective in this numerical challenge is to use the provided data to calculate the discharge…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

2- Both a gage and a manometer are attached to a gas tank to
measure its pressure. If the reading on the pressure gage is P
kPa, determine the distance between the two fluid levels of the
manometer if the fluid is (a) mercury (p = 13,600 kg/m³) or (b)
oil (p = 850 kg/m³).
First names starting
with A to L
First names
with M to Z
P (kPa)
-15
starting -35
Gas
h = ?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

6.79 Oil of a specific gravity of 0.90 is flowing downward through the venturi meter shown in the figure below. If the manometer deflection h is 700 mm, calculate the volume flow rate of oil. 100-mm inside diameter 50-mm inside diameter Flow Mercury (sg- 13.54)
Neglecting vapor pressure, what is the pressure of the air at point E in the container shown? The atmospheric pressure is 1.0 atm (14.7 lbf/in², 101300 Pa). 2 in (5 cm) # 3 in (8 cm) 26 in (66 cm) E civilstrupea amail.com T air SG-0.72 SG - 0.87 mercury SG 13.6
Atmospheric pressure at this location is 102.0 kPa and fluid temperature is presently 30°C. Oil (sg = 0.90) C Water 125 mm 475 mm 250 JU mm 50 mm Mercury (sg = 13.54) Figure 1: Compound manometer (note: sg = specific gravity)
Engineering Mechanics- II (Dynamics) Ind. Assignment- 1 1. The velocity of a particle is given by v = 25t² - 80t - 200, where v is in feet per second and t is in seconds. Plot the velocity v and acceleration versus time for the first 6 seconds of motion and evaluate the velocity when acceleration is zero.
Help me - problem of fluid mechanics
Use 4 decimal places in all the computations.
Fluid mechanics -Civil/mechanical. Please give answer in 30min
AAAAAAAAAAAAAAAAAAAA 2 Pa oil with density 706kgf/" and viscosity 4-7×10 7³9 flows out of storage tank below: Determine the minimum diameter that results in a flow rate of 18 litres per minute. Provide answer in cm H = 1.4m L = 7m
The Venturi meter shown in the sketch below, contracts the flow down to one quarter of its original area. Cold air at 0 deg C flows in the pipe through the Venturi meter. The velocity of the air upstream of the Venturi meter is equal to 40 ft/s and the pressure at the same point is equal to 30 psia. What is the manometer reading if the fluid of the manometer is water with density 1000 kg/m3 . Assume that the air behaves as an ideal gas with molecular weight equal to Mw=29 kg/kmol and constant density evaluated at upstream conditions. Use Bernoulli's equation for your calculations. please respond asap!
Problem 1: Clogged Bathtub This bathtub cost a bundle, but even rich people occasionally have to deal with clogged drains. Part A Write the basic equation for volume balance for this system. What property of the fluid allows us to simplify from mass balance (which is always valid) to volume balance (which is not)? Part B The rich person turns on the faucet to flow at 5.0 gal/min for 15 minutes. Meanwhile, the open drain is draining at 1.0 gal/min. How much water is in the bathtub after 15 minutes? Then, how long will it take to completely drain? Part C Make a plot showing the volume of water versus time.
Please design a rapid sand filter that will effectively remove 65% of thesuspended solids in a flow of 10 cubic meters per minute. The suspendedmaterial consists of particles that are perfectly spherical with a diameter of 10microns. Please use sand with an effective size of 1 mm and a porosity of 0.5.You should limit your clean bed head loss to 0.5 meters per meter. (Pease use an attachment efficiency, α of 0.75)Viscosity of water =1.0087x10-3 Ns/m2Density of water =998.23 kg/m3What are the dimensions of this filter (Depth and Surface Area)?
Compute the absolute pressure in kPA of a given tank if a barometer reads 820mmHg and a pressure gage attached to a tank has a reading of 975cm of oil (S.G. of 0.85) Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: KPA abs. Decimal Places required in the final answer: 3