Which of the following describes galvanic corrosion? Select one: a. Two metals/alloys of different compositions are coupled while exposed to an electrolyte. b. Oxidation and reduction reactions occur randomly over the surface. c. Localized corrosion that may be initiated at a surface defect. d. Corrosion that results from a difference in concentration of ions or dissolved gases in the electrolyte. e. Corrosion that occurs preferentially along grain boundaries. f. Corrosion resulting from the combined action of chemical attack and mechanical abrasion or wear. g. One element is preferentially removed as a result of corrosion. h. Corrosion resulting from the combined action of an applied tensile stress and a corrosive environment.

Which of the following describes galvanic corrosion? Select one: a. Two metals/alloys of different compositions are coupled while exposed to an electrolyte. b. Oxidation and reduction reactions occur randomly over the surface. c. Localized corrosion that may be initiated at a surface defect. d. Corrosion that results from a difference in concentration of ions or dissolved gases in the electrolyte. e. Corrosion that occurs preferentially along grain boundaries. f. Corrosion resulting from the combined action of chemical attack and mechanical abrasion or wear. g. One element is preferentially removed as a result of corrosion. h. Corrosion resulting from the combined action of an applied tensile stress and a corrosive environment.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Why is crevice corrosion a problem? O it occurs wherever a local oxygen variation occurs it increases overall corrosion rates and bulk material loss it occurs in aerated solutions O it causes localised and rapid corrosion in the low oxygen region, producing stress concentrations
An aluminum pipe has a length of 54 m at a temperature of 10°C. An adjacent steel pipe at the same temperature is 8 mm longer. At what temperature will the aluminum pipe be 24 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5x10-6/°C and that the coefficient of thermal expansion for the steel is 12.5×10-6/°C.
A magnesium-lead alloy of mass 6.4 kg consists of a solid a phase that has a composition just slightly below the solubility limit at 300°C (570°F). The magnesium-lead phase diagram is shown in Animated Figure 9.20. (a) What mass of lead is in the alloy? i kg (b) If the alloy is heated to 400°C (750°F), how much more lead may be dissolved in the a phase without exceeding the solubility limit of this phase? kg
I need the answer as soon as possible
26) Given the T-T-T curve below, select the process that will result in a microstructure of nearly all bainite. a. Cool to 400°C, hold for 20 seconds, then quench to room temperature b. Cool to 500°C, hold for 10 seconds, then quench to room temperature c. Quench to 125°C, hold for 10 seconds, then reheat to 600°C for more than 100 seconds d. Cool to 725°C, hold for 1,000 seconds, then quench to 125°C e. Cool to 600°C, hold for 1 second, the quench to room temperature Temperature (°C) f. none of the above 900 800 H A+C 1600 1400 700- 1200 A+P 600 P 1000 500H A+B 800 400- Temperature (°F) 4 A 300- M(start) 200 M(50%) 100- M(90%) 600 50% T 0 1 10 102 103 10 105 106 Time (s) 400 200 27) Fatigue failure situations are typically dependent upon which combination of the following factors? a. Slip plane, slip direction, and orientation of the applied load b. Yield strength, elastic modulus, and ductility of the material c. Temperature, time, and applied stress d. Stress amplitude, frequency of…
?WHAT IS THE Fineness Modulus (FM) as mentioned that is to find in the cell?
An aluminum pipe has a length of 69 m at a temperature of 8°C. An adjacent steel pipe at the same temperature is 5 mm longer. At what temperature will the aluminum pipe be 15 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5×10-6/°C and that the coefficient of thermal expansion for the steel is 12.5×10-6/°C.
An aluminum-alloy rod has a length of 8.1814 cm at 14.00°C and a length of 8.1942 cm at the boiling point of water. (a) What is the length of the rod at the freezing point of water? (b) What is the temperature if the length of the rod is 8.1916 cm? prob (a) Number i Units (b) Number i Units
I need the answer as soon as possible