Why are reaction between ions in aqueous solutions generally much faster than reactions between covalent molecules?

Q: 4. Find the dimensions of a concrete lined open channel used to convey a discharge of 70 m/s. The…

A: Given data  Discharge  Mannings roughness coefficient  Side slope  Bed slope

Q: 20 IN H 1=3 m 3 d 1=3 m 1-3 m Which of the following most nearly gives the force in member cd due to…

A:

Q: Do, parts d, e, f, h

A: If a body  vibrates without the help of any external force it is said to undergo free vibration The…

Q: b) Determine the transformation matrix of all elements.

A:

Q: Calculate the equivalent concentrated force of distributed force diagram, draw the free body diagram…

A: Consider the free body diagram of the beam,

Q: 1. Find the center of gravity of a semicircular section having outer and inner diameters of 200 mm…

A:

Q: A 40-lb aluminum bar, initially at T₁ = 150°F, is placed in a tank together with 190 lb of liquid…

A: Given data: Weight of aluminium bar=40 lb Temperature of aluminium, Ta=150°F Tank of water with…

Q: A cantilever beam having a 4m span carries a uniformly distributed load throughout its length. The…

A: The values given in the question are as follows: Span of the beam(L)=4 m or 4000 mm A36 steel grade…

Q: Question 1: For the truss below, using the method of joints: a) Calculate the degree of static…

A: Sorry I didn't see that you have asked for only part (b)  Ok but i have solved all the parts in…

Q: 4. A 5/8-in-diameter steel rod AB fitted to a round hole near end Cof the wooden member CD. A…

A:

Q: 3. Calculate the SDI for the following samples. Determine if the water needs to be pretreatment…

A: To calculate the SDI, we use the following formula:SDI = (1 - Ti / Tf) * 100 / Ttwhere:Ti is the…

Q: The figure below shows a shaft of three segments It is restrained (fixed support) at both sides and…

A:

Q: g) At what single point along the beam does this maximum occur? h) What are the values of internal…

A:

Q: PC1 PI1 0+000 Lct PT1 R1 11 STATION NORTHINGS EASTINGS 0+000 11475.55 8927.24 PC2 9291.91 9546.66…

A: To Determine Table 3 ( The Stationing of PC, PT, PC2, PCC, PT2, PC3, PRC, PT3 and End of Project)…

Q: Label the maximum and minimum values on the graph. d) Draw the internal bending moment diagram (BMD)…

A:

Q: A rigid, insulated vessel is divided into two compartments connected by a valve. Initially, one…

A:

Q: '. (a) Compute the runoff from a 7-in rainfall on a 1500-acre watershed that has hydrologic soil…

A:

Q: Problem 2. A well is located in a completely confined aquifer with a hydraulic conductivity of 12…

A:

Q: Water contained in a closed, rigid tank, initially at 100 lbf/in², 800°F, is cooled to a final state…

A:

Q: The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and…

A: Finding out twist developed in steel from support B.

Q: Please do parts d, e, and f.

A: Part d, e and f is to be solved

Q: From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m. PKN L/3 m QkN/m Lm Determine the following;…

A:

Q: If F = 730 lb, F = 380 lb, F 620 lb, determine the magnitude of the resultant force acting on the…

A: Resultant force is the sum of all the forces acting horizontally and vertically.We can calculate…

Q: 4.) Consider the 2D beam supported by a pin at A and a roller at B. EXTERNAL FORCES a) Draw a FBD.…

A: Find:

Q: (Knowing that the linear expansion of steel is a = 15.5×10-6 K¯'). How the change of the beam…

A: Using formula for expansion or contraction due to temperature changes

Q: #3 Classify each of the following trusses as statically determinate, statically indeterminate, or…

A:

Q: 4. A trapezoidal channel of bed width 8.0 m, side slopes are 1:1, longitudinal bed slope = 12 cm/Km,…

A:

Q: Air enters a compressor operating at steady state at 15 lbf/in.², 80°F and exits at 200°F. Stray…

A:

Q: 2. A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial…

A: Note :- as per our guidelines we are supposed to answer first three subparts only. Please repost…

Q: Two rods vertically connect beams AB and CD as shown in the figure Point A is fixed supported while…

A:

Q: The figure below shows a simply supported beam with a vertical spring at the mid-span. The beam is…

A: Given, E=210 GPa To determine, Deflection in mm at B induced by vertical load P of 150kN acting…

Q: Stability and determinacy of structures: give the three sets of criteria of stability and…

A: Stability refers to its ability to maintain equilibrium and resist excessive deformations or…

Q: In an experiment, a bar of 30 mm diameter is subjected to pull. The measured extension on gauge…

A: Given data: Diameter of the bar:  Gauge length:  Extension:  Change in diameter: Concept: Poisson's…

Q: 1) Given the following: COURSE LATITUDE DEPARTURE АВ 40 - 80 BC 80 -40 CD unknown unknown DA -90 50…

A:

Q: Figure A2 shows a beam of negligible mass with flexural rigidity El and length 2L. The beam is…

A: A simply supported beam is given, we need to solve first three questions

Q: Determine the LRFD design strength (kN) of the compression member shown. The distance between the…

A:

Q: NEGLECTING THE MASS OF THE BEAM, COMPUTE THE REACTIONS ΑΤΑ ΑND B. 2 kN 1 kN/m 12 kN - m 3 m 6 m

A: