Which among the following is the equation of the elastic curve for a cantilever beam of length L, modulus of elasticity E, moment of inertia I, and a concentrated force P at the free end? a. El y(x) = P + PL 24 x* b. El y(x) — Р% PL - 24 x3 c. El y(x) = P*-- PL 6. x3 d. El y(x) = P +. O a. Equation B O b. Equation A Oc. Equation D O d. Equation C

Which among the following is the equation of the elastic curve for a cantilever beam of length L, modulus of elasticity E, moment of inertia I, and a concentrated force P at the free end? a. El y(x) = P + PL 24 x* b. El y(x) — Р% PL - 24 x3 c. El y(x) = P*-- PL 6. x3 d. El y(x) = P +. O a. Equation B O b. Equation A Oc. Equation D O d. Equation C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

GIVEN: Bars A and C are made of steel and bar B is made of brass. Each bar has a cross-sectional area of 4 in? Esteel = 30 x 10° ksi Ebrass = 15 x 10³ ksi REQ'D: The force in the brass bars and the forces in the steel bars when P = 10 kips Lo003 in.gap 18 in. steel sleel Ass
A beam is subjected to equal bending moments of M₂ = 4200 N·m. The cross-sectional dimensions are b = 110 mm, c = 33 mm, d = 74 mm, and t = 3 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. Answer: (a) y= i M. mm 1₂ = i mm4 S= i mm³ (b) OH = i MPa (c) OK = i MPa (d) Omax = i MPa (typ) b H K
A massless beam supports two weights as shown. Find W such that the supporting force at A is zero. L- L 4 4 2 826 N A B W Your answer
*2-13. The piece of rubber is originally rectangular. Determine the average shear %y at A if the corners B and D are subjected to the displacements that cause the rubber to distort as shown by the dashed lines. 3 mm- D 400 mm A-300 mm- B 2 mm Answer from the back of the book: Yxy = 0.0412 rads X
The beam is supporting a distributed load of w = 1200 lb/ft. b. 60. 3 ft 30 6ft Part A Determine the magnitudes of the resultant internal loadings acting on section b-b through the centroid C on the beam. Express your answers, separated by commas, to three significant figures. vec ? Vab =, Nob =, Mpb %3D kip, kip, kip-ft
Consider the following beam with overhangs: A B You must provide the value of X. For example, if the answer is PL³ 20-EI C O X. PL³ EI L L Calculate the deflection at A (the end opposite of the load) and at D (under the load). Assume that both deflections are downward. The answers will be of the form L D = P enter "0.05" (1/20) in the Canvas quiz. Here are a few hints. You'll have to break up the integral over three segments (A to B, B to C, and C to D). On several spans, one of the moment diagrams will be zero. Remember that the definite integral of zero is equal to zero, i.e., f Oda 0. All the remaining integrals should involve triangles with integration factors of 1/3 and 1/6.
3 The piece of plastic is originally rectangular. Calculate the shear strain Yxy at corners A and B if the plastic distorts as shown by the dashed lines. 2 mm 300 mm 2 mm D -400 mm- mm, B A 4 mm 72 mm 3 mm X
A beam is subjected to equal bending moments of Mz = 3100 N·m. The cross-sectional dimensions are b = 180 mm, c = 35 mm, d = 70 mm, and t = 7 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative.
Determine the force in each member of the loaded truss. The force is positive if in tension, negative if in compression. AB= 31° 59 Answers: BC= 10 B 218 kg i 1870 AC = i -1870 i -1120 N Z Z Z N N
What is the reaction force at joint A and I. What is the C or T, the X and Y components, the length and the load of each member. Also when you put the answers could you put it like it is on the image.
Problem 1 Find the reaction forces of the supports on the beam and the forces in the articulated joints. Check on the calculations using the principle of virtual works. 91² 2ql B q A *+++ 1 t l 1 21 ^ t 1
A beam is shown with a distributed loading force 3 kN. Determine an equation for the shear force and bending moment as a function of the distance □ from its mounting point at B. Plot the functions from 0 < <3 and determine the magnitude of the maximum value in that interval. 3kN T A B [ V(x) L 3 KN. (Hand written and clean writing please )