When a SBIA021 student measured the pH of 1.0M HCI, the student obtained a pH meter and failed to neither check the condition nor the manner of usage of the instrument. The pH meter reading timed out (Did not give a reading) Which of the following problem explanations is most correct? A)The sample in the glass beaker was being swirled vigourously while the electrode was submerged in it for a reading. B)The electrode got submerged much deeper into the solution than it should have. C)All of the above are correct problem explanations O D)The electrode had long direct contact with the environment and the glass membrane got dry.

When a SBIA021 student measured the pH of 1.0M HCI, the student obtained a pH meter and failed to neither check the condition nor the manner of usage of the instrument. The pH meter reading timed out (Did not give a reading) Which of the following problem explanations is most correct? A)The sample in the glass beaker was being swirled vigourously while the electrode was submerged in it for a reading. B)The electrode got submerged much deeper into the solution than it should have. C)All of the above are correct problem explanations O D)The electrode had long direct contact with the environment and the glass membrane got dry.

Basic Clinical Laboratory Techniques 6E

6th Edition

ISBN:9781133893943

Author:ESTRIDGE

Publisher:ESTRIDGE

Chapter6: Basic Clinical Chemistry

Section6.7: Electrolytes

Problem 8RQ

See similar textbooks

Similar questions

Design a serial dilution of a sample to achieve a A) Final dilution of 10-4 using 9.0 mL blanks B) Final dilution of 10-6 using 99 mL blanks C) Final dilution of 10-6 using 9.0 mL blanks
A student performs a serial dilution but is not careful about the correct procedures for using the pipet and volumetric flask. Explain how the following errors would affect the concentrations of the diluted solution: a) The pipet is rinsed with water, but not with the solution that is measured. b) The student uses the rubber bulb to force out the liquid remaining in the tip of the pipet into the volumetric flask. c) After carefully mixing the diluted solution in the volumetric flask, the student pours the solution into a beaker that was not carefully rinsed with solution.
Two students independently determine the volume of water delivered by a 10.00-mL pipet. Each student takes 8 measurements, then computes the average volume delivered and the standard deviation. The results are tabulated below. Average St. Dev. Student A 10.4 mL ±0.7 mL Student B 10.00 mL ±0.02 mL Which statement best describes the results? 1)A: good precision, poor accuracy. B: poor precision, good accuracy. 2)A: poor precision, good accuracy. B: good precision, poor accuracy. 3)A: poor precision, poor accuracy. B: good precision, good accuracy. 4)A: good precision, good accuracy. B: good precision, good accuracy. 5)A: poor precision, poor accuracy. B: poor precision, poor accuracy.
Calculate the CFU present in 150 mL water sample and b) dilution factor up to 5. Consider the following dilution scheme.
Using a P-1000 micropipette, you transfer 800 microliter of ddH2O to a beaker and measure its weight. It turns out to be only 780 milligram; what is the percent error of this micropipette?
The doctor ordered Oxacillin 650mg every 6 hours. The instructions on the 2gm vial states to reconstitute with powder with 11.5ml of sterile water for injection, yielding 220mg/1.5ml. How many ml will you administer? using dimensional analysis and show work
What is the minimum volume of dissolution media required to provide sink condition in dissolution test of a tablet dosage form (its weight: 1350 mg; dose strength: 1000 mg) regarding the following conditions? The molecular weight of an active drug substance is 500 Da; the dissolution media is water and the solubility of active drug substance in water is 10 mg/Ml (4. SLAYT) 500 ml 1000 ml 1350 ml 100 ml 135 ml
How would you perform a 100-fold dilution, if you want the final volume to be 15mL? What volume of sample and volume of dilute would be used?
A nurse reconstituted a vial of 750 mg Cefuroxime Sodium Powder for Injection with 6mL of sterile water for injection. The reconstituted solution was dark amber-colored solution. The package insert states that solution colors range from clear to yellow depending on concentration, diluent, and storage conditions. The nurse was then hesitant to give the patient the solution due to its unusual dark color. Five portions were taken from a batch of cefuroxime sodium. Prior to testing in the instrument, each part was subjected to one of the following conditions: Conditions Specifications Temperature Portion 1: 8°C ± 2°C Portion 2: 30°C ± 2°C Portion 3: 40°C ± 2°C Light Portion 4: Kept in the dark Portion 5: Exposed to direct sunlight 1. Which form of the product – the powder for injection, the reconstituted product, or both – will you subject to the following conditions? Why do you think these forms can best address the problem?
One hundred (100) ml of raw goat's milk bought from a street vendor is added in bottle 1 which initially contains 900 ml diluent. The sample was serially diluted by transferring 10 ml each to the succeeding bottles 2, 3 and 4 all of which contain 90ml diluent. Calculate the final dilution in bottle 4 expressed in decimal number. (Attach a screenshot of your computations at the end of the assessment). 0.01 0.001 0.0001 0.00001 0.000001
In the spread plate method, why is the volume plated usually limited to not more than 0.1 mL?
Explain the color changes observed throughout the peroxide value of oil experiment. Materials:1. Old and fresh oil samples2. Distilled water3. Acetic acid/chloroform solution4. Saturated potassium iodide solution5. Sodium thiosulphate (0.01M)6. 1% Starch indicator: dissolve 1g of starch in 10 ml of water and then add 90 ml of hotwater to it