What will be the strain energy stored in the metallic bar of cross sectional area of 2 cm² and gauge length of 10 cm if it stretches 0.002 cm under the load of 12 kN? 1. 10 N-cm 2. 12 N-cm 3. 14 N-cm 4. 16 N-cm

What will be the strain energy stored in the metallic bar of cross sectional area of 2 cm² and gauge length of 10 cm if it stretches 0.002 cm under the load of 12 kN? 1. 10 N-cm 2. 12 N-cm 3. 14 N-cm 4. 16 N-cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

q7 A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If Poisson's ratio is 0.25 and Young's modulus is 200 GPa, an increase in volume will be (b) 150 mm3 (d) 130 mm3 (a) 160 mm3 (c) 140 mm3
A steel section having a cross section of 20 mm x 30 mm is subjected to an axial force of 240 kN. The steel section has produces a strain of 0.002. If it has a value of Poisson's ratio of 0.30. Which of the following gives the bulk modulus of the steel section. a. 133333 MPa b. 166667 MPa c. 111111 MPa d. 144444 MPa
An aluminum-alloy block (E = 70 GPa) is loaded as shown in the diagram below. The application of this load produces a tensile strain of 500 x 10-6 at A as measured by means of a strain gage. Compute the magnitude of the applied force P and locate the neutral axis. 10 cm 15 cm 30 cm 2.5 cm Gage A
Q.2 The bar is made of an aluminium alloy having a stress-strain diagram that can be approximated by the straight line segment shown. Assuming that this diagram is the same for both tension and compression, determine the moment the bar will support if the maximum strain at the top and bottom fibers of the beam is E max = 0.05. 630 560 420 (MPa) 0.006 0.025 0.05 100mm M € (mm/mm) 75mm
Find the value of strain energy of metallic bar with cross sectional area of 2 cm² and gauge length of 10 cm if it stretches 0.002 cm under the load of 10 kN? 1. 14 N-cm 2. 12 N-cm 3. 16 N-cm 4. 10 N-cm
A prismatic bar has a cross-section of 25 mm x 50 mm and a length of 2 m. If the bar is subjected to an axial tensile force of 90 kN, the bar is elongated by 1.5 mm. What is the tensile stress? (a) 3.6 N/mm² (c) 36 N/mm2 (b) 7.2 N/mm² (d) 72 N/mm²
Question 24 Which one of these microfibrillar angles in the illustration is expected to be stronger in tension? A O a. A O b. B B
Question 1: The piece of plastic is originally rectangular. Given LCD and LAD are 400 and 300 mm, respectively. If the plastic distorts as shown by the dashed lines, a) Determine the average normal strain that occurs along CD. b) Determine the average normal strain that occurs along AD. c) Determine the shear strain Yxy at corner C. 2 mm LCD 2 mm D LAD mm B 12 mm 3 mm mm
A steel bar 30 mm in diameter and 2 m long is encased in a shell of cast iron 5 mm thick. Compute the stress in each material, in MPa, if a compressive axial load of 150 kN is applied to the assembly. For steel, E = 200 MPa and for cast iron, E = 100 %3D GPa ( Select the correct response(s): 29.96 MPa 76.39 MPa 212.21 MPa 106.10 MPa 136.32 MPa 152.79 MPa 59.92 MPa 272.84 MPa
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. P = 10 kN a. What is the stress (MPa) in the Bronze material? b. What is the stress in Aluminum in MPa? c. What is the stress in Steel in MPa?
The state of stress at a point is shown with respect to xy-plane. The state of stress at a point is shown with respect to x'y'-plane? 8 MPa y'v 60° S MPa +S MPa 10 MPa 8 MPa
A steel rod with a cross-sectional area of 0.25in2 is stretched between two fixed points. The tensile force in the rod at 70°F is 1200lb. If a = 6.5x10-6/°F and E = 29x106 psi, What will be the stress at 0°F? At what temperature will the stress be zero? A bronze bar 3m long with a cross-sectional area of 320mm2 is placed between two rigid walls. At ta temperature of -20°c, the gap A = 25mm. Find the temperature at which the compressive stress of the bar will be 35 MPa. Use a = 18x10-6 m/ (m. °C) and E = 80GPA.