What will be the length of given mild steel rod after applying 100 kips force/load ?. If the diameter and length of rod are " and 36 inches.

Q: One shaft is in torsion as shown below. If the magnitude of shear stress at point A is 289.5 MPa,…

A: Given data: Shear stress at point A = SA = 269.5 MPa Radius of point A = rA = 40 mm = 0.04 m Shear…

Q: Assume you have a 30 mm in diameter AISI 1040 steel shaft welded on a rigid surface. Forces applied…

A: Given that, AISI 1040 steelDiameter of shaft, D=30 mm,Torque applied on shaft, T=40 N.mBending load…

Q: A 3/8-inch diameter bolt is subjected to a 2,135-lb tensile load. The bolt passes through a very…

A:

Q: If in a tensile loading application, the factor of safety for one member is set as FS = 2.2 based on…

A: Given:Factor of safety, FS=2.2Tensile failure strength, σfail=614 MPaFind:The load member's…

Q: A 1-in.-diameter steel circular rod is subject to a tensile load that reduces its cross-sectional…

A:

Q: Two horizontal metal plates each 30 mm thick are assembled by means of M25 bolt, a nut and washer.…

A: Sectional front view of plates with bolt, nut and washer.

Q: TA 500 Ib buoy, with a 2 ft radius is tied to the bed of a lake using a steel cable. What is the…

A: Mass of the buoy = 500 lb Need to determine the tensile force in the cable.

Q: The more the material is brittle, the higher angle of twist it exhibits before failure in twisting…

A: The given statement is false.

Q: What would be the tensile strength in pounds per square inch of a specimen measuring 0.375 in. thick…

A: Thickness of specimen=0.375 in Width of specimen=1.0 in Load = 27000 lb

Q: A 5⁄8-inch-thick tension member is connected to two 1⁄4-inch splice plates, as shown in Figure The…

A: Bolts are in double shear ϕrn=24.9 kips/bolt      {from the manual table 7-1} The required strength…

Q: An element made of AISI 1020 CD steel is shown, but to shape it, it had to be machined. It must have…

A: The objective of the question is to determine the critical point of the system, apply Mohr's circle…

Q: A frame is being raised on a pivot point. a crane lifts the frame and shows 315 165 at 45⁰. How much…

A:

Q: A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load…

A: A prismatic bar is a straight structural member having constant cross-sectional area throughout its…

Q: find shear and Binding monont dkagr 5KN/m 3m 5m ThT 3m

A:

Q: If a 10" tall stainless steel rod with diameter of %" is receiving 20K lbs tensile load, how much…

A:

Q: 1-A steel rod having a cross-sectional area of 300 mm2 and is 10 m long .The rod is loading by…

A: The given data are: A=300 mm2=300×10-6 m2L=10 mF=30 kN=30×103 NΔL=5 mm=0.005 m Here, A denotes the…

Q: X Your answer is incorrect. A flanged wooden shape is used to support the loads shown on the beam.…

A: Given : The dimensions are, The free body diagram is,

Q: The diameter of the bolt is .500 inches. Force

A: given:diameter of the bolt d=0.500inforce F= 750pound

Q: 300lb -800lb 30 30 -200lb 600lb FORCE Ibs F= F.Cos(e) F = F.Sin(e)

A:

Q: The central plates a in Fig.12 of the text are 9/16 in. thick and 9 in. wide. The diameter of the…

A:

Q: A 2-in.-diameter round steel rod 10 ft long is subjected toa tensile force of 60 kips. How much will…

A: Given Data⇒Diameter of round steeld=2 inLength of round steelL=10 ft=120 inTensile ForceF=60…

Q: Annealing is a process that can release the residual stress and make the grain size grow larger,…

A: Hardness inversely proportional to squere of grain size so option a was wrong.

Q: B 20 mm- 50 mm 20 mm 100 mm 50 mm 100 mm M = 8 kN-m

A:

Q: If you have a rod with an initial diameter 12 mm, final diameter is 10 mm and yield stress 40Mpa, it…

A:

Q: What is allowable load/stress. Give two different equations that determine the allowable load/stress

A: Allowable stress also known as allowable strength is the maximu stress that can be safely applied to…

Q: 1/2-inch thick steel bar is welded to the vertical support A) Calculate the allowable load if the…

A: Given data as per the question h = 3/16 = 4.7625 mm d =4'' = 101.6 mm L =12''=304.8 mm

Q: Which of the materials depicted in the graph: (Answer with Letter ONLY) Tensile Strength

A: The most ductile material is material C because it's ductility is highest.

Q: Resistance of material against external force also refers to; А. Durability Strength C. Toughness D.…

A: Option B  is correct Strength is that mechanical property of a material by virtue of which it…

Q: QUESTION 10 A load of 6kN is supported as shown in the figure. The weight of the pulley is 2kN.…

A:

Q: . For the following diagram, calculate the force needed to is A-36 steel, wire diameter is 0.125…

A:

Q: what would be the the tensile strenght in pounds per square inch of a specimen measuring 0.375 in.…

A:

Q: 0.75 in. 1'in. -20° 1.5 in.1 in. 3 in. 5 lb D 5 lb

A: Given,

Q: QUESTION 7 Consider the circular bent rod with diameter 20 mm. The free-end of the bend is subjected…

A:

Q: A rectangular plate with a hole is shown in fig that carries a tensile load. Stress value calculated…

A: Given that  A rectangular plate with a hole is shown in fig that carries a tensile load. Stress…

Q: 1. You are to design an axially loaded member that is to carry a load of 5,000 lb. The member is to…

A: Given:

Q: What could be the unit of stress? Select all that applies.     Newton     psi     ksi…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.