What steps are required to draw and use Mohr’s circle?

Q: The velocity of a particle moving along the x axis is defined by V = x3 – 4x² + 6x where V is in m/…

A:

Q: Problem #5 The moment of inertia I of a cheap door of mass M=4.00 kg (about an axis going through…

A: given: mass of dart m=0.3 kg speed of dart v= 20 m/s width of dart R= 0.96m I =moment of inertia of…

Q: is this drawing metric or inch?

A: In the given drawing, the screw size is M8 x 1.25 . That means is it 8 mm nominal size screw. That…

Q: With the help of a neat free-hand sketch, explain how to construct the involute of a circle.

A: construct the involve of a circle.

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: Take o, = -400 kPa, Tzy = -330 kPa. (Figure 1) Part A Determine the equivalent normal-stress…

A:

Q: The grains of wood in the board make an angle of 20° with the horizontal as shown. Using Mohr's…

A: Given that:P=280 Nb=25 mmd=60 mmθ=20ο

Q: I want the methode of counting this two drawing L, and J1 and J2 veryy urgent

A: Full joints are the revolute joint and half joints are the sliding pair.

Q: Question 2 At a given point in a machine component, the following stresses were determined: 150 MPa…

A:

Q: For the given state of stress, determine the planes with compressive normal stress equal to 15 MPa.…

A:

Q: Determine (a) the principal stress (and the rotation to the principal planes), (b) the maximum…

A: Given:The stress in  direction is .The stress in  direction is .The shear stress is .Formula…

Q: Why is it called Mohr's circle?

A: Mohr’s  circle is graphical representation which enables us to visualize the relationships between…

Q: Question 2. point J, what is the maximum shear stress the weld has to with- K 700 mm F=3kN Txy

A:

Q: f the crankshaft in the sliding mechanism below has a uniform angular velocity o 1800rpm. Determine…

A: GivenNBO=1800rpmO2B=63.5BC=152

Q: Ø GIVEN THE ORTHOGRAPHIC VIEWS, CREATE AN ISOMETRIC SKETCH OF THE FOLLOWING OBJECT. VISUALIZATION &…

A: Create isometric view from given orthographic projections.

Q: What is the procedure of using the Mohr's circle?

A: The procedure of Mohr's Circle is given as, (1) Draw the vertical and horizontal coordinates. The…

Q: The 40.64 cm. diameter pulley of a gasoline engine is connected by a belt (which is assumed not to…

A:

Q: the center of the circle divided by two. the radius of the circle O the bottommost point of the…

A: Given

Q: If you have a half circle made of steel and the other half of wood, is the center of the circle…

A:

Q: What is the moment's function?

A: Moment deals with the physical quantities situated at some distance relative to the reference point.…

Q: Question 2 Ox 110 MPa = 28 MPa ay = 40 MPa Txy Determine the stresses for an angle of 30 degrees.

A:

Q: A circle of 60 mm diameter rolls on the circumference of another circle of 200 mm diameter and…

A:

Q: Question 1 A material has a stress of 160MPa [tension X direction] and 120 MPa [compression Y…

A:

Q: How can I draw in mohr's circle?

A: Solution:

Q: 50 MPa

A: The Mohr’s circle is used to determine the principal stresses, normal and shear stress at various…

Q: A simply supported beam of circular cross section of 0.15 m diameter with a span of 1m is subjected…

A:

Q: What does the each point on Mohr’s circle represent?

A:

Q: 3. The velocity of the water in the stream is 1.2 m/s. What is the height of the water in the pitot…

A: The height of the water in a pitot tube can be determined using Bernoulli's equation, which relates…

Q: Two buckets are suspended by cables as shown. Bucket A weights 16 lb, and bucket B weighs 7 lb.…

A: According to the question  WA=16 lb WB=7 lb We need to find  Tension in the Cable DE And EF with…

Q: STATICS AND STENGITH OF MATERIALS Question: Express force Fas a Cartesian vector, then determine its…

A: Given: F = 600 lb a = 1.5 ft b = 5 ft c= 3 ft theta = 60 deg

Q: minimum permissible basic circle radius.

A: Given; A cam with a translating flat-face follower is desired to have the follower motion:…

Q: Please only include the sketch mentioned in the question as I have already provided the calculation…

A: Given: σmax,z=166.67 psi σmax,y=333.33 psi   To sketch: The bending stress distribution about the z…

Q: Let a = 4S m/ sec2, Vo = 5 m/ sec, find V and S at the end of 4 sec.

A:

Q: A bead of mass m slides without friction on a straight wire. The wire rotates with constant velocity…

A: According to lagrane’s equation L=T-V T= kinetic energy V= potential energy T= ½ mvr2 + ½ mvθ2 = 1/2…

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.