List down the formulas for calculating the shear stress and angle of twist of the following cross section shapes. Include a figure for each. The figure should show the parameters listed in the formula. d. Triangular (Equilateral, Solid) e. Elliptical (Solid) f. Thin-walled open sections (single rectangular bar)

List down the formulas for calculating the shear stress and angle of twist of the following cross section shapes. Include a figure for each. The figure should show the parameters listed in the formula. d. Triangular (Equilateral, Solid) e. Elliptical (Solid) f. Thin-walled open sections (single rectangular bar)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A sprinter practicing for the 200-m dash accelerates uniformly from rest at A and reaches a top speed of 36 km/h at the 76-m mark. He then maintains this speed for the next 61 meters before uniformly slowing to a final speed of 31 km/h at the finish line. Determine the maximum horizontal acceleration which the sprinter experiences during the run. Where does this maximum acceleration value occur? Part 1 Answers: (a) al- Finish line Calculate (a) the magnitude of the tangential acceleration near start of the race and (b) the magnitude of the tangential acceleration near the end of the race. (b) lal- i 0.658 i 0.205 m/s² 39.9 m m/s² A Save for Later Last saved 12 minutes ago. Saved work will be auto-submitted on the due date. Auto- submission can take up to 10 minutes. Attempts: 0 of 3 used Submit Answer Part 2 The parts of this question must be completed in order. This part will be available when you complete the part above.
Draw the 1st and 3rd Angle Orthographic sketch of the following part:
I need question 10 answered please and thank you. Question pertains to the print provided and also the sequence of operations listed in the directions.
USE ALL DECIMAL PLACES IN SOLUTIONS AND ROUND OFF YOUR ANSWERS TO NEAREST WHOLE NUMBER. INPUT NUMERICAL VALUE ONLY.
I need these three parts answered (Multiple Choice). If you can not answer all three parts please leave it for another tutor to answer. Thank you. For the two holes identified as datum D, what is the total size tolerance specified for those holes? (Multiple Choice)a. .002'b. .003'c. .004'd. .006' The two holes identified as datum D have a counterbore on one end. What size toleranceis specified for the counterbore diameter? (Multiple Choice)a. .010″ (±.005″; see title block)b. .020″ (±.010″; see title block)c. .030″ (±.015″; see title block) What letter represents the revision status of this print? (Multiple Choice)ABCD
i) The displacement at point A. Enter your answer in mm to 2 decimal places.
A hole is to be drilled as shown by the circle. Using the part geometry shown below, indicate on the part sketch where locator(s) should be positioned according to the 3-2-1 principle. Use dashed lines to indicate locators on hidden surfaces. Also indicate where clamping force(s) should be applied using arrows. Use the minimum number of clamping forces.
PLEASE DO THIS TYPEWRITTEN AND COMPLETE IT, I WILL UPVOTE. IF NOT COMPLETE AND TYPEWRITTEN, NO UPVOTE. THANK YOU
Need help .Please
! Draw a sketch of the above drawing in A3 (or two A4 paper taped together).
Create a list of operations for the blueprint provided below. The list of operations must be in chronological order. • All units are in millimeters• Drill depth: 15mm• Raw material dimension: o Body: 65mm longo Cap: 30mm long• Note: Some corners are chamfered so don’t forget to include it in operations
Draw front and right-side views of the following object with a completed dimensions. Draw in scale 1:1 on A4 sheet. (Problem is taken from "Graphics for Engineers' by Earle) 78 What can we learm from the drawlng ? 1. The dimension note M10x1.5 means that the hole is a threaded hole. R16 O 16, 2 Holes The letter 'M' means that the threads are made by following a metric thread system. The number "10" Is the major dlameter of the hole and the number 1.5 is the pitch of a thread. However, for coarse threads, it is a common practice to omit specifying the pitches. For example, a note M10 means the pitches of the thread is 1.5 mm. In this book, the pitch is specified in order to facilitate drafting. 2. Drawing symbol of a threaded hole is shown below. - Thin Ine (4H pench The ends of this arc does not meet together but approximately 90 degs, apart. Object Ihe (2i pencil .major dlameter pich2 M10x1 5 3. The circular projection surface at a threaded hole that is raised from a cylinder is…